KaydedilenlerDerginizi ekleyin

Dergiler / Challenge Journal of Concrete Research Letters / 2020 / Cilt: 11 - Sayı: 4

An investigation on the properties of woodcrete exposed to high temperature

Mehmet CANBAZ
İlkay KARA
İlker Bekir TOPÇU
Sayfa
105–111
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

As a result of the study, while determining that the chip-cement ratio can be used as 1, it is recommended to use the chip-cement ratio up to 0.5 when the high temperature effect is taken into consideration.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:By combining wood wastes with various binders, construction materials can be produced.
📊
Temel Bulgular & Veri:In this study, prismatic specimens were taken from the mixtures produced considering the chip-cement ratio as 0.25, 0.5 and 1.
💡
Sonuç & Katkı:As a result of the study, while determining that the chip-cement ratio can be used as 1, it is recommended to use the chip-cement ratio up to 0.5 when the high temperature effect is taken into consideration.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

By combining wood wastes with various binders, construction materials can be produced. These materials can be used in non-bearing parts such as wall block, insulation panel. In this study, prismatic specimens were taken from the mixtures produced considering the chip-cement ratio as 0.25, 0.5 and 1. The unit weight, ultrasonic pulse velocity, bending and compressive strengths of the specimens were determined by using the results of the experiments on these specimens. In addition, specimens were kept at 200 and 400°C for 3 hours in order to determine its behavior under high temperature, which is one of the most important problems for wood composites. With the experiments carried out on the cooled specimens, weight and strength losses, changes in ultrasonic pulse velocity were examined. As a result of the study, while determining that the chip-cement ratio can be used as 1, it is recommended to use the chip-cement ratio up to 0.5 when the high temperature effect is taken into consideration.

🔖

Bu Makaleye Atıf Yap

CANBAZ, M., KARA, İ., TOPÇU, İ. B. (2020). An investigation on the properties of woodcrete exposed to high temperature. Challenge Journal of Concrete Research Letters, Cilt: 11 - Sayı: 4, 105–111. https://ajindex.com/articles/158934

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (14)

  1. Aigbomian EP, Fan M (2013). Development of wood-crete from hardwood and softwood sawdust. The Open Construction and Building Technology Journal, 7, 108-117.
  2. Aras U, Kalaycıoğlu H, Yel H, Çok A (2019). Effect of cement and accelerator types on the physico-mechanical properties of cementbonded particleboards. Journal of Anatolian Environmental and Animal Sciences, 4(4), 627-630.
  3. Aras U, Kalaycıoğlu H (2016). Wood based composites and application areas. International Refereed Journal of Engineering and Sciences, 6(3), 120-136.
  4. Ateş E (2018). Determination of the amount of the waste wood dust and its energy value in the city center of Balıkesir. Technological Applied Sciences, 13(4), 329-346.
  5. Bozkurt Y (1982). Cemented particleboards. Journal of Istanbul University Faculty of Forestry, 32(2), 30-34.
  6. DelaGree GD, Yu QL, Brouwers HJH (2014). Wood-wool cement board: optimized inorganic coating. Proceedings of the 14th International Inorganic-Bonded Fiber Composites Conference (IIBCC), 15-19,
  7. Da Nang, Vietnam. EN 633 (1993). Cement-Bonded Particleboards- Definition and Classification. European Standard, Turkey. İstek A, Gençer A (2014). The effect of pumice usage on cemented chipboard properties. II. National Mediterranean Forest and Environment Symposium, 550-567,
  8. Isparta, Turkey. Jorge FC, Pereira C, Ferreira JM (2004). Wood-cement composites: A review. Holz als Roh- und Werkstoff, 62(5), 370-377.
  9. Kalaycıoğlu H, Yel H, Çavdar AD (2012). Cemented wood wool composites and their usage areas. Kastamonu University Faculty of Forestry Journal, 12(1), 122-133.
  10. Kaya Aİ (2020). Some wood based composite materials. Turkchem News Portal, Turkey. Mengeloğlu F, Alma MH (2002). Using wheat stems in composite plate production. Kahramanmaraş Sütçü İmam University Journal of Science and Engineering, 5(2), 37-48.
  11. Miller DP, Moslemi AA (2007). Wood-cement composites: effect of model compounds on hydration characteristics and tensile strength. Wood and Fiber Science, 23(4), 472-482.
  12. Na B, Wang Z, Wang H, Lu X (2014). Wood-cement compatibility review. Wood Research, 59(5), 813-826.
  13. Onursal FR (1996). Investigation of physical and mechanical properties of wood sawdust cement composite. Graduate School of Science Thesis, Istanbul Technical University, İstanbul,
  14. Turkey. Risbrudt CD, Ritter DMA, Wegner TH (2010). Centennial edition wood handbook wood as an engineering material. University of Wisconsin, Forest Products Laboratory, General Technical Report FPLGTR-190. Madison, WI: U.S. 50