Journals / Artvin Çoruh Üniversitesi Orman Fakültesi Dergisi / 2020 / Cilt: 21 - Sayı: 2

Phpysical properties and formaldehyde emission effect of hot press parameters

Sıcak pres parametrelerinin yongalevhanın fiziksel özellikleri ve formaldehit emisyonuna etkisi

Pages
276–283
Publication Date
2022-10-11
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

It is thought that, these differences were caused by hot press parameterswhich are the press speed, press temperature and 1:1.35 moles of urea-formaldehyde.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In recent years, chipboard producers have aimed to reduce production costs by increasing capacitybecause of market conditions.
📊
Key Findings & Data:In this study, It was used 40% scots pine (Pinus sylvestres L), 30% sessileoak (Quercus petraea L), 20% poplar (Populus alba L), 10% sawdust and 1:1.35 moles of urea formaldehyde glue in the particleboard production line.
💡
Conclusion & Impact:It is thought that, these differences were caused by hot press parameterswhich are the press speed, press temperature and 1:1.35 moles of urea-formaldehyde.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In recent years, chipboard producers have aimed to reduce production costs by increasing capacitybecause of market conditions. In this study, It was used 40% scots pine (Pinus sylvestres L), 30% sessileoak (Quercus petraea L), 20% poplar (Populus alba L), 10% sawdust and 1:1.35 moles of urea formaldehyde glue in the particleboard production line. Production parameters remained stable. TheOnly thing hot press production parameters were changed. It was increased press speed and presstemperature from hot press parameters by 15%, 20%, 25%. Physical test and formaldehyde emissionperformances of the produced boards were measured. Based on these measurements on the referenceboards, test analyzes based on five boards were evaluated in each test group. All physical tests; boarddensity (T; 622 gr/cm³, T2; 624.6 gr/cm³, T3; 630 gr/cm³, T4; 630 gr / cm³), thickness swelling 24 hours(T1; 15.24, T2; 13.8%, T3; 16.46%, T4; 15.46%), water absorption 24 hours (T1; 78.14%, T2; 78.52, T3;79.12, T4; 78.62). TS EN 120 perforator method was applied for measure the formaldehyde emission inthe chipboards. Formaldehyde gas emission (T1; 14.53 mg 100gr, T2; 14.84 mg/100gr, T3; 15.16mg/100gr, T4; 15.36 mg/100gr) were analyzed. As a result of the study, physical experiment boardsindicated a little difference among each other. But boards indicated formaldehyde emission highdifference among each other. It is thought that, these differences were caused by hot press parameterswhich are the press speed, press temperature and 1:1.35 moles of urea-formaldehyde.

Özet

Son yıllarda yongalevha üreticileri piyasa şartlarında rekabet edebilmek için kapasite artırarak üretim maliyetlerini azaltabilmeyi hedeflemiştir. Bu çalışmada, yonga levha üretim hattında %40 sarıçam (Pinus sylvestres L), %30 sapsız meşe (Quercus petraea L), %20 kavak (Populus alba L), %10 talaş ve 1:1.35 mol üre-formaldehit tutkalı kullanılmıştır. Proseste üretim parametreleri sabit kaldı. Tek değişken sıcak pres üretim parametreleridir. Sıcak pres parametrelerinden pres hızını ve pres sıcaklığını %15, %20, %25 artırmıştır. Üretilen levhaların fiziksel test ve formaldehit emisyon performansları ölçüldü. Referans levhalar baz alınarak tüm testler yapılmıştır. Her bir test grubundan beş levha ölçülmüştür. Tüm fiziksel testler; levha yoğunluğu (T; 622 gr/cm³, T2; 624.6 gr/cm³, T3; 630 gr/cm³, T4; 630 gr/cm³), kalınlığına suda şişmesi 24 saat (T1; %15.24, T2; %13.8, T3; %16.46, T4; %15.46), 24 saat su alma (T1; %78.14, T2; 78.52, T3; 79.12, T4; 78.62) değerlerinde ölçülmüştür. Levhalardaki formaldehit emisyonu ölçmek için, TS EN 120 perforatör yöntemi uygulanmıştır. Formaldehit gaz emisyonu (T1; 14.53 mg/100gr, T2; 14.84 mg/100gr, T3; 15.16 mg/100gr, T4; 15,36 mg/100gr) analiz edilmiştir. Çalışmanın sonucunda, fiziksel test sonuçları diğer test grupları arasında küçük bir fark olduğu görülmektedir. Fakat levhaların formaldehit emisyonu test sonucu diğer test grupları arasında önemli farklar ölçülmüştür. Bu farklılıklar sıcak pres parametreleri (pres hızı, pressıcaklığı) ve 1:1.35 mol üre formaldehit tutkalından kaynaklandığı düşünülmektedir.

🔖

Cite This Article

ÇAMLIBEL, O. (2022). Phpysical properties and formaldehyde emission effect of hot press parameters. Artvin Çoruh Üniversitesi Orman Fakültesi Dergisi, Cilt: 21 - Sayı: 2, 276–283. https://ajindex.com/articles/450600

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Akbulut T (2000)
  2. Yonga Levha Endüstrisi, Laminart Mobilya Dekorasyon Sanat Tasarım Dergisi,Nisan-Mayıs sayı 7 s.112-119.
  3. Ashori A, Nourbakhsh A (2008) Effect of Pres Cycle and Resin Content on Physical and Mechanical Properties of Particleboard Panels Made from The Underutilized Low- Quality Materials. Industrial Crops and Products, 28, 225-230.
  4. Bardak S, Nemli G, Sarı B, Baharoǧlu M, Zekoviç E (2011) Effects of Density Profile and Hot Press Diagram on the Some Technological Properties of Particleboard Composite. High Temperature Materials and Processes. Volume 30: Issue 1-2.
  5. Biçer A (2014) Sodyum Karboksimetilselüloz (Na-Cmc) Modifiyeli Yonga Levha Üretimi. Yüksek Lisans Tezi, Bartın Üniversitesi,
  6. Fen Bilimleri Enstitüsü, Orman Endüstri Mühendisliği Anabilim Dalı, Orman Ürünleri Kimyası ve Teknolojisi Bilim Dalı, Bartın, 169 s. Boran S, Usta M (2010) Odun esaslı panellerde açığa çıkan formaldehit ve formaldehit sınırları hakkında bilgiler. 3. Ulusal Karadeniz Ormancılık Kongresi, s. 1968-1975.
  7. Boran S, Usta M, Gümüşkaya E (2011) Decreasing formaldehyde emission from medium density fiberboard panels produced by adding different amine compounds to urea formaldehyde resin. International Journal of Adhesion&Adhesive, 31: 674-678.
  8. Gündüz G, Masraf Y (2005) Üç tabakalı yatık yongalı yonga levha üretiminde üretim şartlarının değiştirilmesinin levhaların mekanik ve fiziksel özellikleri üzerine etkisi. ZKÜ, Bartın Orman Fakültesi Dergisi, 7 (8): 49-57.
  9. Grigsby W J, Carpenter J EP, Sargent, R (2014). Investigating the Extent of Urea Formaldehyde Resin Cure in Medium Density Fiberboard: Resin Extractability and Fiber Effects. Journal of Wood Chemistry and Technology Vol; 34, Issue 3, https://doi.org/10.1080/02773813.2013.861850
  10. Iosifov N, Vlcheva L, Ganev S (1991) The effect of the wood species on the physical and mechanical properties of particleboards, Naukaza-Gorata, 28: 1, 87-92; 7 ref. He Z, Zhang Y, Wei W (2012) Formaldehyde and VOC emissions at different manufacturing stages of wood-based panels. Building and Environment, 47: 197-204.
  11. Eroğlu H, Usta M (2000)
  12. Lif Levha Üretim Teknolojisi, Karadeniz Teknik Üniversitesi,
  13. Orman Fakültesi, Genel Yayın No: 200, Fakülte Yayın No: 30, Trabzon, s. 351 Iswanto A H, Azhar I, Supriyanto, Susilowati A (2014) Effect of resin type, pressing temperature and time particleboard properties made from sorghum bagasse. Agriculture, Forestry and Fisheries, 2014; 3(2): 62-66. doi: 10.11648/j.aff.20140302.12 Kalaycıoğlu H (1991) Sah