Journals / Artvin Çoruh Üniversitesi Orman Fakültesi Dergisi / 2026 / Cilt: 27 Sayı: 4

Anthropometric Accommodation of Fixed-Height Workbenches in Furniture Manufacturing: A Worker-Level Ergonomic Screening Across 11 Factories

Mobilya Üretiminde Sabit Yükseklikteki İş Tezgâhlarının Antropometrik Uygunluğu: 11 Fabrikada Çalışan Düzeyinde Bir Ergonomi Taraması

Taner Taşdemir(ARTVİN ÇORUH ÜNİVERSİTESİ, ARTVİN MESLEK YÜKSEKOKULU)0000-0001-6692-6656
Kemal Üçüncü(KARADENİZ TEKNİK ÜNİVERSİTESİ, ORMAN FAKÜLTESİ, ORMAN ENDÜSTRİSİ MÜHENDİSLİĞİ BÖLÜMÜ)0000-0002-6294-6112
Pages
1–12
Publication Date
2026-11-06
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Leave-one-factory-out sensitivity analyses showed that the overall findings remained consistent; however, the direction of the mismatch was substantially influenced by assumptions regarding the location of the effective working point.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Mismatch between fixed-height production workbenches and workers' anthropometric characteristics may lead to awkward working postures.
📊
Key Findings & Data:The study was based on a secondary analysis of anonymized individual-level data collected in 2010 from 11 large-scale furniture factories located in seven provinces of Türkiye.
💡
Conclusion & Impact:Leave-one-factory-out sensitivity analyses showed that the overall findings remained consistent; however, the direction of the mismatch was substantially influenced by assumptions regarding the location of the effective working point.
🔬Design:Araştırma Makalesi
📍Scope:2010 Verileri
⚙️Variables:Ergonomi · Antropometri · Mobilya üretimi

Abstract

Mismatch between fixed-height production workbenches and workers' anthropometric characteristics may lead to awkward working postures. This study aimed to evaluate the anthropometric suitability of fixed workbench heights among male workers in the Turkish furniture manufacturing industry. The study was based on a secondary analysis of anonymized individual-level data collected in 2010 from 11 large-scale furniture factories located in seven provinces of Türkiye. A total of 15 static anthropometric measurements obtained from 408 male production workers were evaluated. For 396 workers with complete information on production lines and elbow height, a working height 5–10 cm below elbow height was considered the anthropometrically suitable range. In the primary analysis, the effective working point was defined as the midpoint of the average workpiece height for each production line, while the workbench surface and the upper surface of the workpiece were evaluated as alternative scenarios. The mean elbow height was 1069.9 mm, with the 5th and 95th percentiles corresponding to 1001.3 and 1149.7 mm, respectively. Under the primary scenario, the effective working point was below the suitable range for 67.9% of workers (n = 269), within the suitable range for 23.5% (n = 93), and above the suitable range for 8.6% (n = 34). Leave-one-factory-out sensitivity analyses showed that the overall findings remained consistent; however, the direction of the mismatch was substantially influenced by assumptions regarding the location of the effective working point. The results indicate that, under the primary assessment approach, fixed workbench heights were anthropometrically suitable for only a limited proportion of workers. These findings highlight the need for ergonomic assessments of workstations and the consideration of adjustable workbench systems in furniture manufacturing. Nevertheless, the results should not be interpreted as direct indicators of musculoskeletal disorder risk or as nationally representative anthropometric standards.

Özet

Sabit yükseklikteki üretim tezgâhlarının çalışanların antropometrik özellikleriyle uyumsuzluğu, çalışma sırasında uygun olmayan vücut duruşlarına neden olabilmektedir. Bu çalışmada, Türkiye mobilya üretim sektöründe çalışan erkek işçilerde sabit tezgâh yüksekliklerinin antropometrik açıdan uygunluğunun değerlendirilmesi amaçlanmıştır. Araştırmada, 2010 yılında yedi ilde bulunan 11 büyük ölçekli mobilya fabrikasından elde edilen anonimleştirilmiş bireysel veriler ikincil analiz yöntemiyle incelenmiştir. Çalışma kapsamında 408 erkek üretim çalışanına ait 15 statik antropometrik ölçüm değerlendirilmiştir. Üretim hattı ve dirsek yüksekliği bilgileri eksiksiz olan 396 çalışan için, dirsek yüksekliğinin 5–10 cm altındaki çalışma yüksekliği antropometrik uygunluk aralığı olarak kabul edilmiştir. Birincil analizde etkili çalışma noktası, üretim hattındaki ortalama iş parçası yüksekliğinin orta noktası esas alınarak belirlenmiş; tezgâh yüzeyi ve iş parçasının üst yüzeyi alternatif senaryolar olarak değerlendirilmiştir. Çalışanların ortalama dirsek yüksekliği 1069.9 mm, 5. ve 95. yüzdelik değerleri ise sırasıyla 1001.3 ve 1149.7 mm olarak belirlenmiştir. Birincil senaryoya göre çalışanların %67.9'unda (n = 269) etkili çalışma noktası uygunluk aralığının altında, %23.5'inde (n = 93) uygunluk aralığında ve %8.6'sında (n = 34) uygunluk aralığının üzerinde bulunmuştur. Her analizde bir fabrikanın dışarıda bırakıldığı duyarlılık analizlerinde genel bulgular korunmakla birlikte, uyumsuzluğun yönünün çalışma noktasına ilişkin varsayımlardan önemli ölçüde etkilendiği belirlenmiştir. Sonuç olarak, sabit tezgâh yüksekliklerinin, kullanılan birincil değerlendirme yaklaşımı kapsamında çalışanların sınırlı bir bölümünün antropometrik özelliklerine uygun olduğu ortaya konulmuştur. Bulgular, mobilya üretiminde çalışma istasyonlarının ergonomik açıdan değerlendirilmesi ve ayarlanabilir tezgâh sistemlerinin geliştirilmesine yönelik gereksinimleri ortaya koymaktadır. Bununla birlikte, sonuçların kas-iskelet sistemi hastalıklarına ilişkin doğrudan risk göstergesi veya ulusal antropometrik standart olarak değerlendirilmemesi gerektiği vurgulanmaktadır.

🔖

Cite This Article

Taşdemir, T., Üçüncü, K. (2026). Anthropometric Accommodation of Fixed-Height Workbenches in Furniture Manufacturing: A Worker-Level Ergonomic Screening Across 11 Factories. Artvin Çoruh Üniversitesi Orman Fakültesi Dergisi, Cilt: 27 Sayı: 4, 1–12. https://doi.org/10.17474/artvinofd.2036199

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (18)

  1. Anacleto Filho, P. C., da Silva, L., Mattos, D., Pombeiro, A., Castellucci, H.I., Colim, A., Carneiro, P., & Arezes, P. (2023). Establishing an anthropometric database: A case for the Portuguese working population. International Journal of Industrial Ergonomics, 97, 103473. https://doi.org/10.1016/j.ergon.2023.103473
  2. Arkouli, Z., Michalos, G., Kokotinis, G., & Makris, S. (2024). Worker-centered evaluation and redesign of manufacturing tasks for ergonomics improvement using axiomatic design principles. CIRP Journal of Manufacturing Science and Technology, 55, 188-209. https://doi.org/10.1016/j.cirpj.2024.10.001
  3. Barroso, M.P., Arezes, P.M., da Costa, L.G., & Miguel, A.S. (2005). Anthropometric study of Portuguese workers. International Journal of Industrial Ergonomics, 35(5), 401-410. https://doi.org/10.1016/j.ergon.2004.10.005
  4. Castellucci, H.I., Viviani, C.A., Molenbroek, J.F.M., Arezes, P.M., Martínez, M., Aparici, V., & Bragança, S. (2019). Anthropometric characteristics of Chilean workers for ergonomic and design purposes. Ergonomics, 62(3), 459–474. https://doi.org/10.1080/00140139.2018.1540725
  5. Castellucci, H.I., Viviani, C., Arezes, P., Molenbroek, J.F.M., Martínez, M., Aparici, V., & Dianat, I. (2020). Applied anthropometry for common industrial settings design: Working and ideal manual handling heights. International Journal of Industrial Ergonomics, 78, 102963. https://doi.org/10.1016/j.ergon.2020.102963
  6. Dianat, I., Molenbroek, J., & Castellucci, H.I. (2018). A review of the methodology and applications of anthropometry in ergonomics and product design. Ergonomics, 61(12), 1696-1720. https://doi.org/10.1080/00140139.2018.1502817
  7. Güleç, E., Akın, G., Sağır, M., Koca Özer, B., Gültekin, T., & Bektaş, Y. (2009). Anadolu insanının antropometrik boyutları: 2005 yılı Türkiye antropometri anketi genel sonuçları. Ankara Üniversitesi Dil ve Tarih-Coğrafya Fakültesi Dergisi, 49(2), 187–201. https://dergipark.org.tr/tr/pub/dtcfdergisi/article/1044246
  8. Hanson, L., Sperling, L., Gard, G., Ipsen, S., & Olivares Vergara, C. (2009). Swedish anthropometrics for product and workplace design. Applied Ergonomics, 40(4), 797-806. https://doi.org/10.1016/j.apergo.2008.08.007
  9. Macdonald, W.A., & Oakman, J. (2024). Changes needed to reduce risk of musculoskeletal disorders. American Journal of Industrial Medicine, 67(7), 575-581. https://doi.org/10.1002/ajim.23613
  10. National Institute for Occupational Safety and Health. (2024a). About ergonomics and work-related musculoskeletal disorders. Centers for Disease Control and Prevention. https://www.cdc.gov/niosh/ergonomics/about/index.html
  11. National Institute for Occupational Safety and Health. (2024b). Hierarchy of controls. Centers for Disease Control and Prevention. https://www.cdc.gov/niosh/hierarchy-of-controls/about/
  12. Pheasant, S. (2003). Bodyspace: Anthropometry, ergonomics and the design of work (2nd ed.). Taylor & Francis.
  13. Taşdemir, T., Üçüncü, K., Balaban, Y., & Aydın, A. (2011). Mobilya üretim işçilerinin antropometrik verilerine göre tezgâh yüksekliklerinin belirlenmesi (Alan çalışması). In E. Kahya & Y. Buruk (Eds.), 17. Ulusal Ergonomi Kongresi Bildiriler Kitabı (s. 37-42). Eskişehir.
  14. Taşdemir, T. (2018). Türkiye mobilya sanayi çalışanlarının antropometrik verilerinin analizi (Doktora Tezi). Karadeniz Teknik Üniversitesi, Fen Bilimleri Enstitüsü, Orman Endüstri Mühendisliği Anabilim Dalı, Trabzon.
  15. Taşdemir, T., & Üçüncü, K. (2023). Analysis of anthropometric data of Turkish furniture industry employees. In P. Altıok Gürel & K. Beşaltı (Eds.), Ankara International Congress on Scientific Research-IX, Proceedings Book (Vol. 1, ss. 267-268). IKSAD Publications.
  16. Viviani, C., Arezes, P.M., Bragança, S., Molenbroek, J., Dianat, I., & Castellucci, H.I. (2018). Accuracy, precision and reliability in anthropometric surveys for ergonomics purposes in adult working populations: A literature review. International Journal of Industrial Ergonomics, 65, 1-16. https://doi.org/10.1016/j.ergon.2018.01.012
  17. Waters, T.R., & Dick, R.B. (2015). Evidence of health risks associated with prolonged standing at work and intervention effectiveness. Rehabilitation Nursing, 40(3), 148-165. https://doi.org/10.1002/rnj.166
  18. Yang, Y., Zeng, J., Liu, Y., Wang, Z., Jia, N., & Wang, Z. (2022). Prevalence of musculoskeletal disorders and their associated risk factors among furniture manufacturing workers in Guangdong, China: A cross-sectional study. International Journal of Environmental Research and Public Health, 19(21), 14435. https://doi.org/10.3390/ijerph192114435