SavedAdd your journal

Journals / Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi / 2015 / Cilt: 30 - Sayı: 2

EFFECT OF WELDING SPEED ON THE MECHANICAL PROPERTIES AND MICROSTRUCTURE OF LASER WELDED AISI 316L STAINLESS STEEL

KAYNAK İLERLEME HIZININ AISI 316L PASLANMAZ ÇELİK LAZER KAYNAKLI BİRLEŞTİRMELERİNİN MEKANİK VE MİKROYAPI ÖZELLİKLERİNE ETKİSİ

Ceyhun KÖSE
Ramazan KAÇAR
Pages
0
Publication Date
2015-06-30
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

As a result of this study, it was found that the mechanical properties of AISI 316L weldment recovered and the microstructure morphology of weld metal altered by increasing laser welding speed due to high cooling rate.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, AISI 316L (X2CrNiMo17-12-2) austenitic stainless steel plates were joined with CO2 Laser Beam Welding (LBW) method.
📊
Key Findings & Data:The welding process were carried out in 50% Ar+50% He shielding gas atmosphere by using 3500W laser power for 90-180-270 cm/min different welding speeds.
💡
Conclusion & Impact:As a result of this study, it was found that the mechanical properties of AISI 316L weldment recovered and the microstructure morphology of weld metal altered by increasing laser welding speed due to high cooling rate.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Lazer ışın kaynağı · AISI 316L · kaynak ilerleme hızı

Abstract

In this study, AISI 316L (X2CrNiMo17-12-2) austenitic stainless steel plates were joined with CO2 Laser Beam Welding (LBW) method. The welding process were carried out in 50% Ar+50% He shielding gas atmosphere by using 3500W laser power for 90-180-270 cm/min different welding speeds. The samples were joined autogenously in butt welding position without using filler metal. In order to determine the mechanical properties of welded joints, the tensile, charpy impact and three point bending tests were applied. In addition, the hardness of the welded sample was measured on the cross section. The microstructure characterization of welded samples was carried out using with optical microscope, scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDS), elementel mapping and X-ray diffraction (XRD) analysis. As a result of this study, it was found that the mechanical properties of AISI 316L weldment recovered and the microstructure morphology of weld metal altered by increasing laser welding speed due to high cooling rate.

Özet

Bu çalışmada, AISI 316L (X2CrNiMo17-12-2) östenitik paslanmaz çelik levhalar CO2 lazer ışını kaynak yöntemi ile birleştirilmiştir. Kaynak işlemi %50 Ar+%50 He gaz korumalı ortamda, 3500W lazer gücüyle ve 90-180-270 cm/dk farklı kaynak ilerleme hızlarında yapılmıştır. Numuneler otomatik olarak alın alına yatay pozisyonda ve ilave metal kullanılmadan birleştirilmiştir. Kaynaklı birleştirmelerin mekanik özelliklerini belirleyebilmek için çekme, çentik darbe ve üç nokta eğme testleri uygulanmıştır. İlave olarak kaynaklı bağlantıların sertlik ölçümü kaynak yönüne dik kesitten gerçekleştirilmiştir. Mikroyapı karakteristikleri ise Optik mikroskop, Taramalı Elektron Mikroskobu (SEM), Enerji Dağılımlı X-Işını Spektroskopisi (EDS), Elemental haritalama ve X-Işını Difraksiyonu (XRD) vasıtasıyla incelenmiştir. Yapılan bu araştırmanın sonucunda, lazer kaynak ilerleme hızının artmasıyla hızlı soğuma sonucunda mekanik özelliklerin iyileştiği ve kaynak metali mikroyapı morfolojisinin değiştiği tespit edilmiştir.

🔖

Cite This Article

KÖSE, C., KAÇAR, R. (2015). EFFECT OF WELDING SPEED ON THE MECHANICAL PROPERTIES AND MICROSTRUCTURE OF LASER WELDED AISI 316L STAINLESS STEEL. Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, Cilt: 30 - Sayı: 2, 0. https://ajindex.com/articles/20437

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (18)

  1. ASM, Introduction to Stainless Steels, Materials Park, Ohio, USA, 2000.
  2. Davis, J.R., Stainless Steels, ASM International, OHIO, USA, 1994.
  3. Smith, W.F., Paslanmaz Çelikler, Mühendislik Alaşımlarının Yapı ve Özellikleri, Cilt 1, Ankara, 169-214, 2000.
  4. Tülbentçi, K., Kaluç, E., Geçmişten Günümüze Paslanmaz Çelikler, META, No 20, 47-52, 1992.
  5. Cross, H.J., Beach, J., ve Levy, L.S., Manufacture, Processing and Use of Stainless Steel, Institute of Occupational Health, Birmingham University, B 15 2TT, UK., 1999.
  6. Benyounis, K.Y., Olabi, A.G., ve Hashmi, M.S.J., “Multi-Response Optimization of CO2 Laser-Welding Process of Austenitic Stainless Steel”, Optics & Laser Technology, Cilt 40, No 1, 76–87, 2008.
  7. Csele, M., Fundamentals of Light Sources and Lasers, John Wiley & Sons, Hoboken, 2004.
  8. Singh, C.S., Zeng, H., Guo, C., ve Cai, W., Lasers: Fundametals, Types and Operations, Nanomaterials: Processing and Characterization With Lasers, First Edition, Wiley-VCH Verlag GmbH & Co. KGaA, 2012.
  9. Durmuş, H., CO2 Lazer Kaynağıyla Birleştirilmiş Al. Matriksli Kompozitlerin Kaynak Bölgesinin Mekanik Özellikleri, Doktora Tezi, Celal Bayar Üniversitesi, Fen Bilimleri Enstitüsü, 2006.
  10. Kou, S., Welding Metallurgy, Second Editon, A John Wiley & Sons, INC., Publication, Hoboken, 2003.
  11. Çelen, S., “Paslanmaz Çeliklerin Lazer Kaynağında Kaynak Parametrelerinin Bağlantının Dayanım ve Korozyon Özelliklerine Etkisinin İncelenmesi”, Yüksek Lisans Tezi, 9 Eylül Üniversitesi, Fen Bilimleri Enstitüsü, 2006.
  12. El-Batahgy, A., “Effect of Laser Welding Parameters on Fusion Zone Shape and Solidification Structure of Austenitic Stainless Steels”, Materials Letters, Cilt 32, No 2-3, 155-163, 1997.
  13. Cunat, P., The Welding of Stainless Steel, Materials and Applications Series, Cilt 3, Second Edition,
  14. Euro Inox, Cilt, Luxembourg, 2007.
  15. Balasubramanian, K.R., Siva Shanmugam, S., ve Buvanashekaran G., “Numerical and Experimental Investigation of Laser Beam Welding of AISI 304 Stainless Steel, Advences and Production Engineering & Management, Cilt 3, No 2, 93-105, 2008.
  16. Duley, W. W., Laser Processing and Analysis of Materials, Plenum Press, New York, 1983.
  17. Pawlak, S.J. ve Dudek, S., “The High Alloy Precipitation Hardening Martensitic Steels and Their Suitability for Welding”, Archives of Materials Science and Engineering, Cilt 41, No 2, 69-76, 2010.
  18. Ren, D., Liu, L., ve Li, Y., “Investigation on Overlap Joining of AZ61 Magnesium Alloy: Laser Welding, Adhesive Bonding, and Laser Weld Bonding” Int J Adv Manuf