SavedAdd your journal

Journals / Mühendis ve Makina / 2024 / Sayı: 717

INVESTIGATION OF HEAT TRANSFER EFFECTS IN A CONFINED IMPINGING JET ARRAY WITH 60° INCLINED SECONDARY JETS

60° EĞİMLİ İKİNCİL JETLERE SAHİP SINIRLANDIRILMIŞ ÇARPAN JET DİZİSİNDE ISI TRANSFERİ ETKİLERİNİN İNCELENMESİ

Haluk Keleş(ARTVIN CORUH UNIVERSITY, FACULTY OF ENGINEERING, ELECTRICAL AND ELECTRONICS ENGINEERING DEPARTMENT)0000-0002-6562-8902
Yücel Özmen(KARADENİZ TEKNİK ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, MAKİNE MÜHENDİSLİĞİ BÖLÜMÜ)0000-0003-1127-1060
Pages
598–627
Publication Date
2024-12-27
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

It is observed that the Nusselt distributions calculated with both turbulence models are similar and the calculated results in the impingement region agree with the experimental results with a margin of error of 9 % and 11 % for the Standard k-ε and Standard k-ω turbulence models, respectively.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the effects of heat transfer on the impingement surface of a confined impinging array jet flow with 60° inclined secondary jets are investigated both experimentally and numerically.
📊
Key Findings & Data:In the experimental section of the study, temperature distributions were obtained with a thermal camera among the middle axis of the impingement plate for 20000 and 30000 values of Reynolds number and 0.5, 1, 3 and 6 values of the aperture among plates.
💡
Conclusion & Impact:It is observed that the Nusselt distributions calculated with both turbulence models are similar and the calculated results in the impingement region agree with the experimental results with a margin of error of 9 % and 11 % for the Standard k-ε and Standard k-ω turbulence models, respectively.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Çarpan dizi jet · eğimli ikincil jet · sınırlandırıcı levha

Abstract

In this study, the effects of heat transfer on the impingement surface of a confined impinging array jet flow with 60° inclined secondary jets are investigated both experimentally and numerically. In the experimental section of the study, temperature distributions were obtained with a thermal camera among the middle axis of the impingement plate for 20000 and 30000 values of Reynolds number and 0.5, 1, 3 and 6 values of the aperture among plates. In the numerical section of the study, for the same Reynolds number and spacing values, bidimensional solutions were performed with the Kato Launder modified version of the Standard k-ε and Standard k-ω turbulence models and the calculated temperature distributions on the target impingement plate were compared with the experimental results. With measured temperature distributions, the effect of Reynolds number and aperture between plates on the Nusselt distributions on the target impingement plate is investigated. The Nusselt values on the surface of target impingement plate increase with increasing Reynolds number and decrease with increasing aperture between plates. The Nusselt number takes top point values at the impingement positions of the secondary jets on the impingement plate in the direction of their axes, and the positions of the top points shift to larger ±r/D values with increasing inter-plate spacing. It is observed that the Nusselt distributions calculated with both turbulence models are similar and the calculated results in the impingement region agree with the experimental results with a margin of error of 9 % and 11 % for the Standard k-ε and Standard k-ω turbulence models, respectively.

Özet

Bu çalışmada, 60° eğimli ikincil jetlere sahip sınırlandırılmış çarpan dizi jet akışında çarpma yüzeyindeki ısı transferi etkileri hem deneysel hem de sayısal olarak incelenmiştir. Çalışmanın deneysel kısmında, Reynolds sayısı değerleri 20000 ve 30000, levhalar arası açıklık değerleri 0.5, 1, 3 ve 6 için çarpma levhasının merkez ekseni üzerince termal kamera ile sıcaklık dağılımları elde edilmiştir. Çalışmanın sayısal kısmında ise, Reynolds sayısının 30000 değerinde aynı açıklık değerleri için Standard k-ε ve Standard k-ω türbülans modellerinin Kato Launder ile modifiye edilmiş versiyonları kullanılarak 2-boyutlu çözümler gerçekleştirilmiş ve çarpma levhası üzerinde hesaplanan sıcaklık dağılımları deneysel sonuçlarla karşılaştırılmıştır. Ölçümlenen sıcaklık dağılımlarıyla, Reynolds sayısı ve levhalar arası açıklık değerlerinin çarpma levhası üzerindeki Nusselt dağılımlarına etkisi araştırılmıştır. Çarpma levhası boyunca Nusselt değerleri artan Reynolds sayısı ile artmakta, artan levhalar arası açıklık değerleri ile azalmaktadır. Çarpma levhası üzerinde ikincil jetlerin eksenleri doğrultusundaki çarpma konumlarında Nusselt sayısı pik değerler almakta ve oluşan piklerin konumları artan levhalar arası açıklı ile daha büyük ±r/D değerlerine kaymaktadır. Her iki türbülans modeliyle hesaplanan Nusselt dağılımlarının benzer olduğu ve çarpma bölgesinde hesaplanan sonuçların Standard k-ε ve Standard k-ω türbülans modelleri için sırasıyla % 9 ve % 11’lik hata payı ile deneysel sonuçlara uyum sağlandığı görülmektedir.

🔖

Cite This Article

Keleş, H., Özmen, Y. (2024). INVESTIGATION OF HEAT TRANSFER EFFECTS IN A CONFINED IMPINGING JET ARRAY WITH 60° INCLINED SECONDARY JETS. Mühendis ve Makina, Sayı: 717, 598–627. https://doi.org/10.46399/muhendismakina.1599408

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (32)

  1. Abdel-Fattah, A. (2007). Numerical and experimental study of turbulent impinging twin-jet flow. Experimental Thermal and Fluid Science, 31, 1061-1072. Doi: https://doi.org/10.1016/j.expthermflusci.2006.11.006
  2. Aldabbagh, L. B. Y., & Mohamad, A. A. (2007). Effect of jet-to-plate spacing in laminar array jets impinging. Heat and Mass Transfer, 43, 265-273. Doi: https://doi.org/10.1007/s00231-006-0109-7
  3. Aldabbagh, L. B. Y., & Sezai, I. (2002). Numerical simulation of three-dimensional laminar, square twin-jet impingement on a flat plate, flow structure, and heat transfer. Numerical Heat Transfer Part A: Applications, 41, 835-850. Doi: https://doi.org/10.1080/10407780290059378
  4. Al Mubarak, A. A., Shaahid, S. M., & Al-Hadhrami, L. M. (2013). Heat transfer in a channel with inclined target surface cooled by single array of centered impinging jets. Thermal Science, 17, 1195-1206. Doi: https://doi.org/10.2298/TSCI110630010A
  5. Attalla, M., & Specht, E. (2009). Heat transfer characteristics from in-line arrays of free impinging jets. Heat and Mass Transfer, 45, 537-543. Doi: https://doi.org/10.1007/s00231-008-0452-y
  6. Baz, F. B., Elshenawy, E. A., El-Agouz, S. A., El-Samadony, Y. A. F., & Marzouk, S. A. (2024). Experimental study on air impinging jet for effective cooling of multiple protruding heat sources. International Journal of Thermal Sciences, 196, 108707. Doi: https://doi.org/10.1016/j.ijthermalsci.2023.108707
  7. Bergman, T. L., Lavine, A. S., Incropera, F. P., & Dewitt, D. P. (2011). Introduction to Heat Transfer (6th ed.). Wiley.
  8. Buchlin, J. M. (2011). Convective Heat Transfer In Impinging-Gas-Jet Arrangements. Journal of Applied Fluid Mechanics, 4, 137-149. Doi: https://doi.org/10.36884/jafm.4.02.11926
  9. Caliskan, S., Baskaya, S., & Calisir, T. (2014). Experimental and numerical investigation of geometry effects on multiple impinging air jets. International Journal of Heat and Mass Transfer, 75, 685-703. Doi: https://doi.org/10.1016/j.ijheatmasstransfer.2014.04.005
  10. Chuang, S. H., Chen, M. H., Lii, S. W., & Tai, F. M. (1992). Numerical simulation of twin-jet impingement on a flat plate coupled with cross-flow. International Journal of Numerical Methods for Heat & Fluid Flow, 14, 459-475. Doi: https://doi.org/10.1002/fld.1650140406
  11. Chuang, S. H., & Nieh, T. J. (2000). Numerical simulation and analysis of three-dimensional turbulent impinging square twin-jet flow field with no-crossflow. International Journal of Numerical Methods for Heat & Fluid Flow, 33, 475-498. Doi: https://doi.org/10.1002/1097-0363(20000630)33:4%3C475::AID-FLD16%3E3.0.CO;2-Q
  12. Churchill, S. W., & Chu, H. H. S. (1975). Correlating equations for laminar and turbulent free convection from a vertical plate. International Journal of Heat and Mass Transfer, 18, 1323-1329. Doi: https://doi.org/10.1016/0017-9310(75)90243-4
  13. Dagtekin, I., & Oztop, H. F. (2008). Heat transfer due to double laminar slot jets impingement onto an isothermal wall within one side closed long duct. International Communications in Heat and Mass Transfer, 35, 65-75. Doi: https://doi.org/10.1016/j.icheatmasstransfer.2007.05.013
  14. Dong, L. L., Leung, C. W., & Cheung, C. S. (2004). Heat transfer and wall pressure characteristics of a twin premixed butane/air flame jets. International Journal of Heat and Mass Transfer, 47, 489-500. Doi: https://doi.org/10.1016/j.ijheatmasstransfer.2003.07.019
  15. Fernández, J. A., Elicer-Cortés, J. C., Valencia, A., Pavageau, M., & Gupta, S. (2007). Comparison of low-cost two-equation turbulence models for prediction flow dynamics in twin-jets devices. International Communications in Heat and Mass Transfer, 34, 570-578. Doi: https://doi.org/10.1016/j.icheatmasstransfer.2007.02.011
  16. Geers, L. F. G., Hanjalic, K. & Tummers, M. J. Wall imprint of turbulent structures and heat transfer in multiple impinging jet arrays, J. Fluid Mech., 546, 2006, 255-284. Doi: https://doi.org/10.1017/S002211200500710X
  17. Godi, S.C., Pattamatta, A. & Balaji, C. (2020). Heat transfer from a single and row of three dimensional wall jets - A combined experimental and numerical study, Int. J. Heat Mass Transf. 159, 119801, Doi: https://doi.org/10.1016/j.ijheatmasstransfer.2020.119801.
  18. Guoneng, L., Zhihua, X., Youqu, Z., Wenwen, G. & Cong, D. (2016). Experimental study on convective heat transfer from a rectangular flat plate by multiple impinging jets in laminar cross flows, Int. J. Therm. Sci. 108, 123–131, Doi: https://doi.org/10.1016/j.ijthermalsci.2016.05.006.
  19. Kato, M., & Launder, B. E. (1993). The modeling of turbulent flow around stationary and vibrating square cylinders. In Proceedings of the 9th Symposium on Turbulent Shear Flows (pp. 10.4.1–10.4.6).
  20. Kline, S., & McClintock, F. (1953). Describing uncertainties in single-sample experiments. Mechanical Engineering, 75, 3-8.
  21. Maddox, J. F., Knight, R. W., & Bhavnani, S. H. (2015). Liquid Jet Impingement With an Angled Confining Wall for Spent Flow Management for Power Electronics Cooling With Local Thermal Measurements. Journal of Electronic Packaging, 137.Doi: https://doi.org/10.1115/1.4030953
  22. Miao, J. M., Wu, C. Y., & Chen, P. H. (2009). Numerical investigation of confined multiple-jet impingement cooling over a flat plate at different crossflow orientations. Numerical Heat Transfer Part A: Applications, 55, 1019-1050. Doi: https://doi.org/10.1080/10407780903014335
  23. Ozmen, Y. (2011). Confined impinging twin air jets at high Reynolds numbers. Experimental Thermal and Fluid Science, 35, 355-363. Doi: https://doi.org/10.1016/j.expthermflusci.2010.10.006
  24. Ozmen, Y., & Baydar, E. (2013). A numerical investigation on confined impinging array of air jets. Journal of Thermal Science and Technology, 33, 65-74.
  25. Ozmen, Y., & Ipek, G. (2016). Investigation of flow structure and heat transfer characteristics in an array of impinging slot jets. Heat and Mass Transfer, 52, 773-787.Doi: https://doi.org/10.1007/s00231-015-1598-z
  26. Polat, S., Huang, B., Mujumdar, A. S., & Douglas, W. J. M. (1989). Numerical flow and heat transfer under impinging jets: A review. Annual Review of Numerical Fluid Mechanics and Heat Transfer, 2, 157-197. Doi: https://doi.org/10.1615/AnnualRevHeatTransfer.v2.60
  27. San, J. Y. & Chen, J. J. (2014). Effects of jet-to-jet spacing and jet height on heat transfer characteristics of an impinging jet array, Int. J. Heat Mass Transf. 71 (2014) 8–17, Doi: https://doi.org/10.1016/j.ijheatmasstransfer.2013.11.079.
  28. Seyedein, S. H., Hasan, M., & Mujumdar, A. S. (1995). Turbulent flow and heat transfer from confined multiple impinging slot jets. Numerical Heat Transfer Part A: Applications, 27, 35-51. Doi: https://doi.org/10.1080/10407789508913687
  29. Talapati, R. J., Baghel, K., Shrigondekar, H., & Katti, V. V. (2024). Influence of inclined unconfined circular air jet impingement on local heat transfer characteristics of smooth flat plate. International Journal of Thermal Sciences, 197, 108848. Doi: https://doi.org/10.1016/j.ijthermalsci.2023.108848
  30. Tepe, A. Ü. (2019). Gaz Türbin Kanatlarında Jet Çarpmalı Soğutmanın Deneysel ve Sayısal İncelenmesi [Doktora tezi, Karabük Üniversitesi Lisansüstü Eğitim Enstitüsü].
  31. Yang, Y. T., & Shyu, C. H. (1998). Numerical study of multiple impinging slot jets with an inclined confinement surface. Numerical Heat Transfer Part A: Applications, 33, 23-37. Doi: https://doi.org/10.1080/10407789808913926
  32. Yalçınkaya, O., Durmaz, U., Tepe, A. Ü., Benim, A. C., & Uysal, Ü. (2024). Heat and Flow Characteristics of Aerofoil-Shaped Fins on a Curved Target Surface in a Confined Channel for an Impinging Jet Array. Energies, 17(5), 1238. Doi: https://doi.org/10.3390/en17051238