Journals / Mühendis ve Makina / 2026 / Cilt: 66 Sayı: 721

INVESTIGATION OF CNG TANKS OF COMMERCIAL PASSENGER BUS WITH VIRTUAL ANALYSES WITHIN THE SCOPE OF ECE 110 REGULATIONABSTRACT

TEST EDİLMİŞ BİR TİCARİ YOLCU OTOBÜSÜNÜN SANAL ARAÇ DİNAMİĞİ MODELLERİNİN OPTİMİZASYON İLE DOĞRULANMASI

Pages
647–673
Publication Date
2026-01-07
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

As a result of virtual analyses, the virtual vehicle model was verified with test data by providing competencies at certain speeds in wheel center movement, damper displacement, chassis vertical displacement changes, and lateral slip angle values.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In a Class-III commercial vehicle project to be produced by Anadolu Isuzu company, data obtained from lane change and bump pass tests performed with a prototype vehicle, virtual vehicle model verification studies were carried out with a virtual vehicle model created as part of R& D studies.
📊
Key Findings & Data:Vertical displacement values of the chassis were compared and verified with 4-poster virtual analyzes.
💡
Conclusion & Impact:As a result of virtual analyses, the virtual vehicle model was verified with test data by providing competencies at certain speeds in wheel center movement, damper displacement, chassis vertical displacement changes, and lateral slip angle values.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Araç Dinamiği Analizi · Adams/Car · Araç Dinamiği Testleri

Abstract

In a Class-III commercial vehicle project to be produced by Anadolu Isuzu company, data obtained from lane change and bump pass tests performed with a prototype vehicle, virtual vehicle model verification studies were carried out with a virtual vehicle model created as part of R& D studies. In order to be able to perform the physical tests performed on the prototype vehicle in a virtual environment, the same road models were also created in virtual conditions, and virtual tests were performed using the MSC Adams/Car program. Since the characteristics of the wheel installed on the test vehicle have yet to be fully discovered, they will be able to differ depending on the wheel used in the virtual model. Especially in the lane change test, the reaction of the wheels and the driver's behavior will affect the test data. In order to evaluate the data decisively, it is aimed to verify the peaks between the maneuvers. In addition, the method of obtaining values appropriate to the test data by changing the wheel parameter values that most affect the lateral sliding angle of the wheels with the help of pSeven optimization software was followed. The minimum and maximum lateral slip angle values obtained in the test results were determined as the target, and optimization analyses were performed. Vertical displacement values of the chassis were compared and verified with 4-poster virtual analyzes. As a result of virtual analyses, the virtual vehicle model was verified with test data by providing competencies at certain speeds in wheel center movement, damper displacement, chassis vertical displacement changes, and lateral slip angle values.

Özet

Anadolu Isuzu firması tarafından üretilecek olan Class-III ticari araç projesinde, prototip araç ile gerçekleştirilen şerit değiştirme ve tümsek geçiş testlerinden elde edilen veriler, Ar-Ge çalışmaları kapsamında oluşturulan sanal araç modeli ile sanal araç modeli doğrulama çalışmaları gerçekleştirilmiştir. Prototip araç üzerinde gerçekleştirilen fiziksel testlerin sanal ortamda da gerçekleştirilebilmesi için aynı yol modelleri sanal koşullarda da oluşturulmuş ve MSC Adams/Car programı kullanılarak sanal testler gerçekleştirilmiştir. Test aracına takılan tekerleğin özellikleri henüz tam olarak keşfedilmediği için sanal modelde kullanılan tekerleğe göre farklılık gösterebilecektir. Özellikle şerit değiştirme testinde tekerleklerin tepkisi ve sürücünün davranışı test verilerini etkileyecektir. Verilerin kararlı bir şekilde değerlendirilebilmesi için manevralar arasındaki tepe noktalarının doğrulanması hedeflenmektedir. Ayrıca pSeven optimizasyon yazılımı yardımıyla tekerleklerin yanal kayma açısına en çok etki eden tekerlek parametre değerlerinin değiştirilerek test verilerine uygun değerlerin elde edilmesi yöntemi izlenmiştir. Test sonuçlarında elde edilen minimum ve maksimum yanal kayma açısı değerleri hedef olarak belirlenmiş ve optimizasyon analizleri gerçekleştirilmiştir. Şasinin düşey deplasman değerleri 4-poster sanal analizleri ile karşılaştırılmış ve doğrulanmıştır. Sanal analizler sonucunda tekerlek merkez hareketi, damper deplasmanı, şasi dikey deplasman değişimleri ve yanal kayma açısı değerlerinde belirli hızlarda yeterlilikler sağlanarak sanal araç modeli test verileri ile doğrulanmıştır.

🔖

Cite This Article

Yılmaz, A. S., Çifci, E., Canpolat, B., Türkan, Ö., Salman, U. C. (2026). INVESTIGATION OF CNG TANKS OF COMMERCIAL PASSENGER BUS WITH VIRTUAL ANALYSES WITHIN THE SCOPE OF ECE 110 REGULATIONABSTRACT. Mühendis ve Makina, Cilt: 66 Sayı: 721, 647–673. https://doi.org/10.46399/muhendismakina.1619597

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (18)

  1. Albinsson, A., & Routledge, C. (2013). The damper levels influence on vehicle roll, pitch, bounce, and cornering behaviour of passenger vehicle. Master's Thesis in Automotive Engineering, Chalmers University of Technology, Sweden. Erişim Adresi: https://odr.chalmers.se/server/api/core/bitstreams/da15e2f9-a56b-4a24-8901-edacbcdea924/content.
  2. Altair. (t.y.). Introduction into design of experiments DOE with HyperStudy eBook. Erişim Adresi: https://advanced-eng.cz/wp-content/uploads/2021/06/2021_ebook-HyperStudy.pdf
  3. Arslan, A., Kaptanoğlu, M., & Şenocak, E. (2012). Kuzey Amerika pazarı için geliştirilen bir aracın FMVSS 208 regülasyonuna uygunluğunun sanal olarak doğrulanması. 6. Otomotiv Teknolojileri Kongresi (OTEKON 2012), Bursa, Türkiye. Erişim Adresi: https://otekon.org/dokuman/books/6thOtekonBook.pdf
  4. ASTM. (2015). Standard Guide for Conducting Friction Tests for Pavement Surfaces Using the Two-Wheel Brake-Force Trailer (ASTM E1926-15). ASTM International.
  5. Ayçiçek, T. (2002). (Bir taşıt seyir dinamiği modeli.) Yüksek Lisans Tezi, İstanbul Teknik Üniversitesi, Fen Bilimleri Enstitüsü, İstanbul. Erişim Adresi: https://polen.itu.edu.tr:8443/server/api/core/bitstreams/6023e3e9-59ad-4419-bdbb-0479a831e444/content
  6. Demir, A. (2013). Taşıt teknolojisi: Teker dinamiğinin incelenmesi. Marmara Üniversitesi Teknoloji Fakültesi, İstanbul. Erişim Adresi: https://www.abdullahdemir.net/ders-notlari/tasit-teknolojisi/tasit-teknolojisi-tekerlek-dinamiginin-incelenmesi/
  7. Orgül, B. O., Koyuncu, M. L., Dileroğlu, S., & Gökçe, H., (2010). Ticari Araç Geliştirme Projesi Kapsamında Dinamik Modelin Testler İle Doğrulanması. Otekon 5. Otomotiv Teknolojileri Kongresi, Bursa, Turkey. Erişim Adresi: https://www.otekon.org/dokuman/books/2thOtekonBook.pdf
  8. International Organization for Standardization. (2018). ISO 3888-1:2018: Passenger cars—Test track for a severe lane-change manoeuvre—Part 1: Double-lane change. Erişim Adresi: https://cdn.standards.iteh.ai/samples/67973/daa839ed4aca420788d9b4a51cd6cc95/ISO-3888-1-2018.pdf
  9. ISO. (2016). Mechanical vibration – Road surface profiles – Reporting of measured data (ISO 8608:2016). International Organization for Standardization.
  10. ISO. (2018). Road vehicles – Functional safety – Part 1: Vocabulary (ISO 26262-1:2018). International Organization for Standardization.
  11. Kumar, S. (2015). (Suspension design feasibility study of light commercial vehicle in Adams/Car.) Yüksek Lisans Tezi, Politecnico di Milano, School of Industrial and Information Engineering, İtalya. Erişim Adresi: https://www.politesi.polimi.it/handle/10589/112888
  12. Kutluay, E., & Winner, H. (2014). Validation of vehicle dynamics simulation models - A review. Vehicle System Dynamics, 52(2), 186–217.Doi: https://doi.org/10.1080/00423114.2013.868500
  13. MSC Software. (2017). Vehicle modeling and simulation using Adams/Car: Workbook. Erişim Adresi: https://www.scribd.com/document/729784209/Adams-2017-2-Training-740-Workbook
  14. MSC Software. (2019). Adams Tire Help (for Adams 2019.2): Documentation. Erişim Adresi: https://simcompanion.hexagon.com/customers/s/article/adams-configure-help--for-adams-2019-2--doc12082
  15. Trade Delegation of the Russian Federation in the United Kingdom. (2016). Software development company DATADVANCE. Rustrade. Erişim adresi: https://rustrade.org.uk
  16. United Nations Economic Commission for Europe. (2018). Regulation No. 107: Uniform provisions concerning the approval of category M2 or M3 vehicles with regard to their general construction. Official Journal of the European Union, L 42, 1–295. Erişim Adresi: https://op.europa.eu/en/publication-detail/-/publication/d8730fbc-157e-11e5-8817-01aa75ed71a1
  17. Van Gennip, M. (2018). Vehicle dynamic modelling and parameter identification for an autonomous vehicle.
  18. Yüksek Lisans Tezi, Delft University of Technology, Hollanda Scholtz, R. A. (1993). The spread spectrum concept. In N. Abramson (Ed.), Multiple access (pp. 121–123). IEEE Press. Erişim Adresi: https://uwspace.uwaterloo.ca/items/c2aa65f7-1747-4fdb-bdda-3d94acef5935