Dergiler / Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi / 2020 / Cilt: 10 - Sayı: 4

Investigation of the Effect of Cutting Parameters on the Surface Roughness Value in the Machining of AISI 4140 Steel with Taquchi Method

Sayfa
2840–2849
Yayın Tarihi
2020-12-15
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The f on surface roughness values (Ra and Rz) was found to have an effect of 99.34% and 98.47%, respectively.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:AISI 4140 steel material has a wide range of usage in the industry.
📊
Temel Bulgular & Veri:In this experimental study, the effect of cutting parameters on surface roughness (Ra and Rz) during the turning of AISI 4140 steel was analyzed using the Taguchi method.
💡
Sonuç & Katkı:The f on surface roughness values (Ra and Rz) was found to have an effect of 99.34% and 98.47%, respectively.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Taguchi method · Surface roughness · Machinability

Özet

AISI 4140 steel material has a wide range of usage in the industry. Before this material is hardened, rough turning is performed. Besides the surface roughness value is very important in terms of machinability. In this experimental study, the effect of cutting parameters on surface roughness (Ra and Rz) during the turning of AISI 4140 steel was analyzed using the Taguchi method. This study, Taguchi L9 was designed in 3 different cutting speeds (100, 140 and 180 m min-1), 3 different feed rates (0.08, 0.12 and 0.16 mm rev-1), and 3 different depth of cut (0.5, 0.9 and 1.3 mm). In the analysis of experimental data, S/N (signal/noise) ratios and variance analysis were used to analyze the effect of cutting parameters on the surface roughness value. The degrees of influence on Ra according to S/N ratios are the feed rate ( f ), cutting speed (V), and depth of cut (a), respectively, from large to small. On Rz, the effects of cutting parameters respectively were observed to be in f, a, and V. The f on surface roughness values (Ra and Rz) was found to have an effect of 99.34% and 98.47%, respectively.

Abstract

AISI 4140 steel material has a wide range of usage in the industry. Before this material is hardened, rough turning is performed. Besides the surface roughness value is very important in terms of machinability. In this experimental study, the effect of cutting parameters on surface roughness (Ra and Rz) during the turning of AISI 4140 steel was analyzed using the Taguchi method. This study, Taguchi L9 was designed in 3 different cutting speeds (100, 140 and 180 m min-1), 3 different feed rates (0.08, 0.12 and 0.16 mm rev-1), and 3 different depth of cut (0.5, 0.9 and 1.3 mm). In the analysis of experimental data, S/N (signal/noise) ratios and variance analysis were used to analyze the effect of cutting parameters on the surface roughness value. The degrees of influence on Ra according to S/N ratios are the feed rate ( f ), cutting speed (V), and depth of cut (a), respectively, from large to small. On Rz, the effects of cutting parameters respectively were observed to be in f, a, and V. The f on surface roughness values (Ra and Rz) was found to have an effect of 99.34% and 98.47%, respectively.

🔖

Bu Makaleye Atıf Yap

İYNEN, O., ŞAHİNOĞLU, A., ÖZDEMİR, M., YILMAZ, V. (2020). Investigation of the Effect of Cutting Parameters on the Surface Roughness Value in the Machining of AISI 4140 Steel with Taquchi Method. Iğdır Üniversitesi Fen Bilimleri Enstitüsü Dergisi, Cilt: 10 - Sayı: 4, 2840–2849. https://ajindex.com/articles/256437

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (12)

  1. Akkurt M, 1998. Talaş Kaldırma Yöntemleri ve Takım Tezgâhları. Birsen Yayınevi,
  2. İstanbul.
  3. Asiltürk İ, Akkuş H, 2011. Determining the effect of cutting parameters on surface roughness in hard turning using the Taguchi method, Measurement 44:1697-1704.
  4. Asiltürk İ, Çunkaş M, 2011. Modeling and prediction of surface roughness in turning operations using artificial neural network and multiple regression method, Expert Systems with Applications, 38:5826-5832.
  5. Chavoshi SZ, Tajdari M, 2010. Surface roughness modelling in hard turning operation of AISI 4140 using CBN cutting tool, Int J Mater Form 3:233-239.
  6. Daim JP, Gaitonde VN, Karnik SR, 2008. Investigations into the effect of cutting conditions on surface roughness in turning of free machining steel by ANN models, Journal of materials processing technology 205:16-23.
  7. Das SR, Dhupal D, Kumar A, 2015. Study of surface roughness and flank wear in hard turning of AISI 4140 steel with coated ceramic inserts, Journal of Mechanical Science and Technology 29:4329-4340.
  8. Das SR, Panda A, Dhupal D, 2017. Analysis of surface roughness in hard turning with coated ceramic inserts: Cutting parameters effects, prediction model, cutting conditions optimization and cost analysis, Ciência e Técnica Vitivinícola 32:127-154.
  9. Demir H, Özlü B, 2009. Sertleştirilmiş 30MnVS6 mikroalaşımlı çeliğin kesme kuvvetleri ve yüzey pürüzlülüğü açısından işlenebilirliğinin araştırılması. Erciyes Üniversitesi Fen Bilimleri Enstitüsü Dergisi 25:262-271.
  10. Gür AK, Taşkaya S, Özay Ç, 2019. Ramor 500 Çeliğinde Isıl İşlemin Mikroyapı, Mikrosertlik ve Abrasiv Aşınma Direncine Etkisinin Taguchi Metoduyla Değerlendirilmesi, BEÜ Fen Bilimleri Dergisi 8:1045-1056. Günay M, 2013. AISI 316L çeliğinin işlenmesinde takım radyüsü ve kesme parametrelerinin Taguchi yöntemiyle optimizasyonu. Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, 28:437-444.
  11. Hessainia Z, Belbah A, Yallese MA, Mabrouki T, Rigal JF, 2013. On the prediction of surface roughness in the hard turning based on cutting parameters and tool vibrations, Measurement 46:1671-1681. Koçak H, 2011. GGG 90 Küresel Grafitli Dökme Demirin İşlenebilirliğinin Kesme Kuvvetleri Yüzey Pürüzlülüğü ve Takım Aşınması Açısından Değerlendirilmesi, Gazi Üniversitesi Fen Bilimleri Enstitüsü, M. Sc. Thesis, Ankara.
  12. Motorcu AR, Işık Y, Kuş A, Çakır MC, 2016. Analysis of The Cutting Temperature and Surface Roughness During The Orthogonal Machining of AISI 4140 Alloy Steel Via The Taguchi Method, Materials and techn