SavedAdd your journal

Journals / Mühendislik Bilimleri Dergisi / 2009 / Cilt: 15 - Sayı: 2

Basit Mesnetli Kirişlerde Eğilme ve Kaymadan Dolayı Oluşan Sehim Denklemlerinin Bulunması

Derivation of Equations for Flexure and Shear Deflections of Simply Supported Beams

Ümran ESENDEMİR
Pages
187–193
Publication Date
2022-10-18
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The shear effect is the smallest for 45 orientation angle and the biggest for 0 orientation angle

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Shear deflection of wood beams generally is exluded in plannning calculations.
📊
Key Findings & Data:Ignoring shear deflection could cause significant errors, expecially for short and thick beams.
💡
Conclusion & Impact:The shear effect is the smallest for 45 orientation angle and the biggest for 0 orientation angle
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

Shear deflection of wood beams generally is exluded in plannning calculations. Ignoring shear deflection could cause significant errors, expecially for short and thick beams. In this study, two deflection functions due to flexure and shear of simply supported composite beam subjected to single force are obtained analytically. Wood being high shear modulus according to other material is selected for sample problem. The deflections the mid point of the beam are calculated to see the effect of shear by using the obtained functions for 0, 15, 30, 45, 60 and 90 orientation angles. Also, bending stresses at the mid point of the short beam are given for 0, 15, 30, 45, 60 and 90 orientation angles. It is shown that the magnitude of shear deflection depends on force, length and height of the beam. The shear effect is the smallest for 45 orientation angle and the biggest for 0 orientation angle

Özet

Kiriş uygulamalarının genelinde kaymadan dolayı oluşan sehimler ihmal edilir. Fakat; yüksek kayma modülüne sahip, kısa ve kalın kirişlerde kaymadan dolayı oluşan sehimin ihmal edilmesi çok büyük hatalara neden olmaktadır. Bu çalışmada her iki tarafında mesnetlenmiş orta noktasından tekil yüke maruz kompozit kirişlerdeki eğilme ve kaymadan dolayı ortaya çıkan sehim denklemleri analitik olarak elde edilmiştir. Örnek malzeme olarak kayma modülü diğer malzemelere göre yüksek olan ahşap seçilmiştir. Kaymanın etkisini incelemek için, elde edilen fonksiyonlar kullanılarak, kirişin orta noktasındaki maksimum sehimler 0, 30, 45, 60 and 90 oryantasyon açıları için elde edilmiştir. Aynı zamanda kayma etkisinin en fazla olduğu kısa kirişin orta noktasındaki eğilme gerilmeleri 0, 30, 45, 60 ve 90 oryantasyon açıları için verilmiştir. Kaymadan dolayı oluşan sehimin; kirişe uygulanan yüke, kirişin uzunluğuna ve yüksekliğine göre değiştiği tespit edilmiştir. Kayma etkisi; 45 oryantasyon açısında en küçük, 0 oryantasyon açısında ise en büyük olmaktadır

🔖

Cite This Article

ESENDEMİR, Ü. (2022). Basit Mesnetli Kirişlerde Eğilme ve Kaymadan Dolayı Oluşan Sehim Denklemlerinin Bulunması. Mühendislik Bilimleri Dergisi, Cilt: 15 - Sayı: 2, 187–193. https://ajindex.com/articles/583314

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Altenbach, H. 2000. On the determination of trans- verse shear stiffnesses of orthotropic plates, Zeitschrift für Angewandte Mathematik and Physik, 51 (4), 629-649.
  2. Aydoğan, M. 1995. Stiffness-matrix formulation of beams with shear effect on elastic foundation, Journal of Structural Engineering, 121 (9), 1265- 1270. Biblis, E. J. 1997. Shear deflection of two species lami- nated wood beams, Wood Science and Technol- ogy. 1 (3), 231-238.
  3. Esendemir, Ü. 2004. An elastic-plastic stress analysis in a polymer-matrix composite beam of arbi- trary orientation supported from two ends acted upon with a force at the mid point. Journal of Re- inforced Plastics and Composites, 23 (6), 613-623.
  4. Esendemir, Ü. 2005. The effects of shear on the de- flection of linearly loaded composite cantilever beam, Journal of Reinforced Plastics and Compos- ites. 24 (11), 1159-1168.
  5. Esendemir, Ü., Usal, M.R., Usal, M. 2006. The effects of shear on the deflection of simply supported composite beam loaded linearly, Journal of Rein- forced Plastics and Composites. 25 (8), 835-846.
  6. Evangelas, J. Biblis, 1967. Shear deflection of two spe- cies laminated wood beams, Wood Science and Technology. 1 (3), 231-238.
  7. Faella, C., Martinelli, E., and Nigro, E. 2003. Shear con- nection nonlinearity and deflections of steel concrete composite beams: a simplified method, Journal of Structural Engineering. 129 (1), 12-20.
  8. Hiroaki, K., Tohru, N. 1993. Shear deflection of aniso- tropic plates. JSME Internatianal Journal Series A: Mechanics and Material Engineering. 36 (1). 73- 79. Jones, R. M. 1975. Mechanics of composite materials. Mcgraw-Hill, Kogakusha, Tokyo. Kılıç, O., Aktaş, A. and Dirikolu, M.H. 2001. An investi- gating of the effects of shear on the deflection of an orthotropic cantilever beam by use of aniso- tropic elasticity theory. Composites Science and Technology. (61), 2055-2061.
  9. Kubojima, Y., Ohtani, T., and Yoshihara, H. 2004. Effect of shear deflection on vibrational properties of compressed wood, Wood Science and Technol- ogy. 38 (3), 237-244.
  10. Lee, S.J, Reddy, J.N. 2004. Nonlinear deflection con- trol of laminated plates using third-order shear deformation theory, International journal of Me- chanics and Materials Design, 1 (1), 33-61.
  11. Lekhnitskii, S.G. 1968.
  12. Anisotropic Plates, Gordon and Breach Science, New York. Lekhnitskii, S.G. 1981. Theory of Elasticity of an Aniso- tropic Body. Mir Publishers,
  13. Moscow. Liu, J.Y and Rammer, D.R. 2003. Analysis of wood can- tilever loaded at free end