SavedAdd your journal

Journals / International Advanced Researches and Engineering Journal / 2021 / Cilt: 5 - Sayı: 2

Determination of the effect of artificial aging parameters on dry sliding wear resistance of 6013 aluminum alloy (Al-Mg-Si-Cu)

Mehmet AYVAZ
Pages
181–187
Publication Date
2022-10-19
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The lowest specific wear rate was determined as 3.542x10-3 mm3/Nm in the AA6013 sample aged artificially for 2 hours at 200 °C.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the effect of artificial aging parameters, applied to AA6013 aluminum alloys commonly used in the automotive and aerospace sectors, on wear resistance was examined.
📊
Key Findings & Data:For this purpose, AA6013 aluminum alloy samples were solutionized at 575 °C for 60 minutes and then they were artificially aged for 2, 4, and 6 hours at 180 and 200 °C temperatures.
💡
Conclusion & Impact:The lowest specific wear rate was determined as 3.542x10-3 mm3/Nm in the AA6013 sample aged artificially for 2 hours at 200 °C.
🔬Design:Research Article
📍Scope:6013 samples
⚙️Variables:Aluminum · AA 6013 · Artificial aging

Abstract

In this study, the effect of artificial aging parameters, applied to AA6013 aluminum alloys commonly used in the automotive and aerospace sectors, on wear resistance was examined. For this purpose, AA6013 aluminum alloy samples were solutionized at 575 °C for 60 minutes and then they were artificially aged for 2, 4, and 6 hours at 180 and 200 °C temperatures. Mean hardness was measured as 66.6 HV in the solutionized samples taken. It was determined that as a result of artificial aging, α-AlFeMnSi intermetallic phase precipitation were formed between α-Al grains. By the effect of precipitation hardening, an increase in hardness was observed in all artificially aged samples; the highest hardness was found as an average of 149.3 HV in AA6013 samples aged artificially for 2 hours at 200 °C. A general decrease in the friction coefficients of samples aged at both 180 °C and 200 °C was observed along with the artificial aging temperature. The lowest specific wear rate was determined as 3.542x10-3 mm3/Nm in the AA6013 sample aged artificially for 2 hours at 200 °C.

🔖

Cite This Article

AYVAZ, M. (2022). Determination of the effect of artificial aging parameters on dry sliding wear resistance of 6013 aluminum alloy (Al-Mg-Si-Cu). International Advanced Researches and Engineering Journal, Cilt: 5 - Sayı: 2, 181–187. https://ajindex.com/articles/539280

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Atilio I., Braga, V., Siqueira, R. H. M, Carvalho, S. M., Lima, M. S. F., Comparing the weldability of AA6013‑t4 aluminium alloy on DP600 dual‑phase steel with laser welding and resistance spot welding, Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2020. 42(71): p. 1-12
  2. Şimşek, İ., Şimşek, D., Özyürek, D., The effect of different sliding speeds on wear behavior of ZrO2 reinforcement aluminium matrix composite materials. Internatinoal Advanced Researches and Engineering Journal, 2020. 4(1): p. 1-7
  3. Wilm, A., Physico-metallurgical investigations of aluminium alloys containing magnesium. Metallurgie, 1911. 8: p. 255-227
  4. Guinier, A., Structure of age-hardened aluminium-copper alloys. Nature, 1938. 14: p. 569–570
  5. Preston, G. D., The diffraction of x-rays by age-hardening aluminium copper alloys. Proceedings of the Royal Society of London, 1938. 167(931): p. 526-538
  6. Dutta, I., Allen, S.M., A calorimetric of precipitation in commercial aluminum alloy 6061. Journal of Materials Science Letters, 1991. 10: p. 323-326
  7. Pogatscher, S., Antrekowitsch, H., Leitner, H., Ebner, T., Uggowitzer, P. J., Mechanisms controlling the artificial aging of Al–Mg–Si alloys. Acta Materialia, 2011. 59: p. 3352-3363
  8. Kaneko, R.S., Bakow, L., Lee, E.W., Aluminum alloy 6013 sheet for new U.S. navy aircraft. JOM, 1990. 42: p. 16-18
  9. Staab, T.E.M., Krause-Rehberg, R., Hornauer, U., Zschech, E., Study of artificial aging in AlMgSi (6061) and AlMgSiCu (6013) alloys by Positron Annihilation. Journal of Material Science, 2006. 41: p. 1059–1066
  10. Buha, J., Lumley, R.N., Crosky, A.G., Hono, K., Secondary precipitation in an Al–Mg–Si–Cu alloy. Acta Materialia, 2007. 55: p. 3015-3024
  11. Barbosa, C., Rebello, J.M.A., Acselrad, O., Dille, J., Delplancke, J.-L., Identification of precipitates in 6013 aluminum alloy (Al-Mg-Si-Cu). International Journal of Materials Research, 2002. 93(3): p. 208-211
  12. Erdoğan, M., Tekin, R., Kaya, M., Mikrodalga firinda suni yaşlandirilan 6013 alüminyum alaşimin korozyon davranişinin incelenmesi (Investigation of corrosion behavior of 6013 aluminum alloy aged artificially in microwave oven). Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi, 2014. 20(1): p. 25-30
  13. Abo Zeid, E.F., Mechanical and electrochemical characteristics of solutionized AA 6061, AA6013 and AA 5086 aluminum alloys. Journal of Materials Research and Technology, 2019. 8(2): p. 1870-1877
  14. Liu, M., Jiang, T., Wang, J., Liu, Q.