SavedAdd your journal

Journals / Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi / 2009 / Cilt: 24 - Sayı: 3

Investigation of the cutting forces components as experimentally and statistically on hobs

Azdırma freze çakılarında kesme kuvveti bileşenlerinin deneysel ve istatistiksel olarak incelenmesi

Alaattin KAÇAL
Mahmut GÜLESİN
Pages
453–460
Publication Date
2022-10-18
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Cutting forces on experiments performed by coated hob average ratio of % 59 lower than uncoated hobs.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, relations between cutting force components and cutting parameters have been investigated as experimental and statistically during gear hobbing process.
📊
Key Findings & Data:Gears are machined using TiN coated and uncoated hobs, Ç 8620 material in machining test.
💡
Conclusion & Impact:Cutting forces on experiments performed by coated hob average ratio of % 59 lower than uncoated hobs.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In this study, relations between cutting force components and cutting parameters have been investigated as experimental and statistically during gear hobbing process. Gears are machined using TiN coated and uncoated hobs, Ç 8620 material in machining test. Additionally, ANOVA (Analysis of variance) tests of experimental results were carried out using MINITAB R14 software. With respect to the experimental results force component of Fz at direction of feed rate shown that more sensitive to variation of cutting parameters. Cutting forces on experiments performed by coated hob average ratio of % 59 lower than uncoated hobs.

Özet

Bu çalışmada, azdırma yöntemi ile dişli çark açma işlemi sırasında meydana gelen kesme kuvveti bileşenlerinin kesme parametreleri ile ilişkileri deneysel ve istatistiksel olarak incelenmiştir. İşleme deneylerinde TiN kaplamalı ve kaplamasız HSS azdırma çakılar kullanılarak, Ç 8620 malzemeden dişli çarklar işlenmiştir. Ayrıca, MINITAB R14 yazılımı kullanılarak deney sonuçlarının ANOVA (varyans analizi) testleri yapılmıştır. Deney sonuçlarına göre; ilerleme yönündeki Fz-kuvvet bileşeninin kesme parametrelerindeki değişimlere karşı daha duyarlı olduğu görülmüştür. Kaplamalı azdırma ile yapılan deneylerde kesme kuvvetleri kaplamasız azdırmalardan ortalama % 59 oranında daha az çıkmıştır.

🔖

Cite This Article

KAÇAL, A., GÜLESİN, M. (2022). Investigation of the cutting forces components as experimentally and statistically on hobs. Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, Cilt: 24 - Sayı: 3, 453–460. https://ajindex.com/articles/523852

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (19)

  1. İpekçioğlu N., “Frezecilik”, Milli Eğitim Basımevi, 1984
  2. Sel S., “Notlar”, HEMA Dişli Fabrikası, Ankara, 2000
  3. Bouzakis K.D., Kombogiannis S., Antoniadis A., Vidakis N.,, “Gear hobbing cutting process simulation and tool wear prediction models”, Journal of Manufacturing Science and Engineering, Vol. 124, 42-51, 2002
  4. Sulzer G., ‘‘Leistungssteigerung bei der Zylinderradherstellung durch genaue Erfassung der Zerspankinematik,’’ Dissertation, TH Aachen,1974
  5. Bouzakis K. D., and Antoniadis A., ‘‘Optimizing Tool Shift in Gear Hobbing,’’ CIRP Ann., 44, 1995
  6. Cooke D.A.D, Welbourn D.B., “Forces in gear hobbing-1”, Machinery (Lond), Vol. 111, No. 2860, 475-477, 1967
  7. Cooke D.A.D, Welbourn D.B., “Forces in gear hobbing-1”, Machinery (Lond), Vol. 112, No. 2882, 258-261, 1968
  8. Wakuri A.; Ueno, T.; Ainoura M., “Study of gear hobbing” Japan Society of Mechanical Engineers -- Bulletin, Vol. 9, No. 34, 409-416, 1966
  9. Hannam R.G.; Andrew C., “Analysis of geometry of gear hobbing” Institution of Mechanical Engineers -- Proceedings, V 182, N 25, 559- 570, 1967-1968
  10. Thamer “Investigation of the cutting force in hobbing”, Research report, Aachen Polytechnic, 1964
  11. Ziegler “Cutting forces when hobbing straightand helical tooth spur gears”, Research report, Aachen Polytechnic, 1966
  12. Ohtubo T., “Simple equations for cut amount in hobbing”, Nippon Kikai Gakkai Ronbunshu, C Hen/Transactions of the JSME, Part C Vol. 55, Issue 511, 818-819, 1989
  13. Koenig W., Bouzakis K., “Determination of the time course of the cutting force components in gear hobbing”, ASME, (Paper) Issue 80 - C2/DET-75, 9, 1980
  14. Bashkirov, V.N., “Experimental study of the dynamics of hobbing with coarse-module hobs”, Soviet Engineering Research, Vol. 4, Issue 12, 67-69, 1984
  15. Deb Sr., Bhattacharyya A., “Forces in gear cutting”, Journal of the Institution of Engineers (India): Mechanical Engineering Division, Vol. 51, Issue 5 pt ME3, 102-107, 1971
  16. Bhattacharyya A, Deb Sr., “Mechanics of gear hobbing”, ASME- 69-WA/Prod-7, 6 1969
  17. Ohtubo T., “Study on designing gear cutting fixtures”, Nippon Kikai Gakkai Ronbunshu, C Hen/Transactions of the JSME, Part C Vol.55, Issue 515, 1820-1822, 1989
  18. Ali K. A., “Experimental determination of relatıonship of cutting force wıth cutting parameters”, Mechanical Engineering Research Bulletin (Dhaka), Vol. 7, 29-32, 1984
  19. Ohtubo T., “Simple equations for predictıon of cutting forces in gear hobbing”, Nippon Kikai Gak