Journals / El-Cezeri / 2021 / Cilt: 8 - Sayı: 2

The Effect of Afşin-Elbistan Fly Ash with Different Particle Size As Geopolymer Raw Material

Farklı Tane Boyutuna Sahip Afşin-Elbistan Uçucu Külünün Geopolimer Hammaddesi Olarak Kullanımı

Journal
El-Cezeri
Pages
751–765
Publication Date
2021-05-31
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

These results are also supported by XRD and TGA analysis.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:It is aimed to be used as a raw material in the production of geopolymer mortars containing Afşin - Elbistan fly ash with a high rate of calcium oxide in two different grain sizes.
📊
Key Findings & Data:In the design of these mortar mixtures, the activator/binder ratio was kept constant as 0.55, the water/binder ratio as 0.50 and the sand/ binder ratio as 0.30.
💡
Conclusion & Impact:These results are also supported by XRD and TGA analysis.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Afşin-Elbistan uçucu külü · geopolimer harç · ultrasonik ses hızı

Abstract

It is aimed to be used as a raw material in the production of geopolymer mortars containing Afşin - Elbistan fly ash with a high rate of calcium oxide in two different grain sizes. In the design of these mortar mixtures, the activator/binder ratio was kept constant as 0.55, the water/binder ratio as 0.50 and the sand/ binder ratio as 0.30. Sodium silicate (SS) and sodium hydroxide (SH) were used together as activators. SS/SH ratio is 1 and 1.5, the molarity of sodium hydroxide is 10 and 14 M, and the curing temperature is 60 ºC and 90 ºC for 24 hours. The fresh and hardened unit weight, ultrasonic velocity and compressive strength properties of these samples were investigated. In addition, changes in the microstructure were investigated by thermogravimetric analysis and X-ray diffraction analysis. The highest compressive strength 14GF0.55/1.5-90 (14M SH, use of ground fly ash, activator/binder ratio 0.55, SS/SH ratio 1.5 and 90 ºC curing temperature) was given and this value was 10.30 MPa. The increase in the molarity from 10 to 14 and the SS / SH from 1 to 1.5 increased the mechanical properties due to the increase in geopolymerization reactions. Also, the UPV results have increased due to the denser structure. These results are also supported by XRD and TGA analysis.

Özet

İki farklı tane boyutuna sahip yüksek oranda kalsiyum oksit içeren Afşin – Elbistan uçucu külü içeren geopolimer harçların üretilmesinde hammadde olarak değerlendirilmesi amaçlanmıştır. Bu harç karışımlarının tasarımında aktivatör/bağlayıcı oranı 0,55 su/bağlayıcı oranı 0,50 ve kum/bağlayıcı oranı 0,30 olarak sabit tutulmuştur. Aktifleştirici olarak sodyum silikat (SS) ve sodyum hidroksit (SH) beraber kullanılmıştır. SS/SH oranı 1 ve 1,5, sodyum hidroksitin molaritesi 10 ve 14 M ve kür sıcaklığı ise 24 saat boyunca 60 ºC ve 90 ºC sıcaklık seçilmiştir. Bu numunelerin yayılma, taze ve sertleşmiş birim ağırlık, ultrasonik geçiş hızı ve basınç dayanımı özellikleri incelenmiştir. Ayrıca mikroyapıda meydana gelen değişiklikler, termogravimetrik analizi (TGA) ve X-ışını kırınım analizi (XRD) ile araştırılmıştır. En yüksek basınç dayanımı 14GF0,55/1,5-90 (14M SH, öğütülmüş uçucu kül, aktivatör/bağlayıcı oranı 0,55, SS/SH oranı 1,5 ve 90 ºC kür sıcaklığı) numunesi vermiş ve bu değer 10,30 MPa’dır. Molaritenin 10'dan 14'e ve SS/SH'nin 1'den 1,5'e yükselmesi, geopolimerizasyon reaksiyonlarındaki artıştan dolayı mekanik özellikleri de artmıştır. Ayrıca daha yoğun yapı nedeniyle UPV sonuçları da artmıştır. Bu sonuçlar aynı zamanda XRD ve TGA analizleri ile de desteklenmektedir.

🔖

Cite This Article

SEVİNÇ, A. H. (2021). The Effect of Afşin-Elbistan Fly Ash with Different Particle Size As Geopolymer Raw Material. El-Cezeri, Cilt: 8 - Sayı: 2, 751–765. https://ajindex.com/articles/252198

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Kantarcı, F., Türkmen, İ., Ekinci, E., “Optimization of Production Parameters of Geopolymer Mortar and Concrete: A Comprehensive Experimental Study”, Construction and Building Materials, 2019, 228; 116770. Yaşar, B.A., Köse, M.M., Avğın, S., Temiz, H., “Düşük Dayanımlı Betonların Elastisite Modülünün Bulunması”, El-Cezerî Fen ve Mühendislik Dergisi, 2020, 7 (3); 1384-1397.
  2. Saka, R.C., Gökdemir, A., Subaşı, S., “Sepiyolit İkameli Çimentolu Karışımların Mekanik ve Fiziksel Özelliklerinin İncelenmesi”, El-Cezerî Fen ve Mühendislik Dergisi 2018, 5(2); 681-692.
  3. Özdemir, İ., Koçak, Y., “Pirinç Kabuğu Külü İkameli Çimentoların Fiziksel Ve Mekanik Özelliklerinin Araştırılması”, El-Cezerî Fen ve Mühendislik Dergisi 2020, 7(1); 160-168.
  4. Toniolo, N., Boccaccini, A. R.,” Fly Ash-Based Geopolymers Containing Added Silicate Waste. A Review”, Ceramics International, 2017, 43(17); 14545–14551.
  5. Topçu, İ. B., Sofuoğlu, T., “Pres Filtre Atığı ve Uçucu Kül ile Elde Edilen Geopolimer Harçların Farklı Koşullar Altında Birim Ağırlığı ve Basınç Dayanımının Değerlendirilmesi”, El-Cezerî Fen ve Mühendislik Dergisi 2020, 7 (2); 806-823.
  6. Liew, K. M., Sojobi, A. O., Zhang, L. W., “Green Concrete: Prospects and Challenges”, Construction and Building Materials, 2017, 156; 1063–1095.
  7. Meesala, C. R., Verma, N. K., Kumar, S., “Critical Review On Fly‐Ash Based Geopolymer Concrete”, Structural Concrete, 2019, 1–16.
  8. Chindaprasirt, P., Chareerat, T., Sirivivatnanon, V., “Workability and Strength of Coarse High Calcium Fly Ash Geopolymer”, Cement and Concrete Composites, 2017, 29(3); 224–229.
  9. Davidovits, J., “Geopolymer Chemistry and Application”, 2nd Ed., Institute Geopolymer, Saint-Quentin, France, 585s, 2008.
  10. Khale D., Chaudhary R., “Mechanism of Geopolymerization and Factors Influencing its Development: A Review”, Journal of Materials Science, 2007, 42; 729–746.
  11. Chindaprasirt, P., Chareerat, T., Hatanaka, S., Cao, T., “High-Strength Geopolymer Using Fine High-Calcium Fly Ash”, Journal of Materials in Civil Engineering, 2011, 23(3); 264–270.
  12. Siddique, R, “Performance Characteristics of High-Volume Class F Fly Ash Concrete”, Cement and Concrete Research, 2004, 34; 487–493.
  13. Siddique, R., Khatib, J.M., “Abrasion Resistance and Mechanical Properties of High-Volume Fly Ash Concrete”, Materials and Structures, 2010; 43; 709–718.
  14. Chindaprasirt, P., De Silva, P., Sagoe-Crentsil, K., Hanjitsuwan, S., “Effect of SiO2 and Al2O3 on the Setting and Hardening of High Calcium Fly Ash-Based Geopolymer Syste