Journals / Artvin Çoruh Üniversitesi Orman Fakültesi Dergisi / 2026 / Cilt: 27 Sayı: 4

Effects of Some Machining Parameters on Cutting Power in CNC Milling of Oriental Beech (Fagus orientalis L.) and Scots pine (Pinus sylvestris L.) woods

Doğu Kayını (Fagus orientalis L.) ve Sarıçam (Pinus sylvestris L.) Odunlarının CNC Frezelenmesinde Bazı İşleme Parametrelerinin Kesme Gücü Üzerine Etkileri

Ali Cakmak(KARADENİZ TEKNİK ÜNİVERSİTESİ, FEN BİLİMLERİ ENSTİTÜSÜ, ORMAN ENDÜSTRİ MÜHENDİSLİĞİ (DR))0000-0002-0827-022X
Pages
1–14
Publication Date
2026-10-30
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results indicated that the statistical models were highly significant (p < 0.001) with explanatory powers of 82.5% for Oriental beech and 87.2% for Scots pine.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This study focused on the influence of machining parameters and wood properties on cutting power in the CNC milling of Oriental beech and Scots pine.
📊
Key Findings & Data:The results indicated that the statistical models were highly significant (p < 0.001) with explanatory powers of 82.5% for Oriental beech and 87.2% for Scots pine.
💡
Conclusion & Impact:Therefore, the findings of this study could help to select suitable cutting conditions and maintain the sharpness of cutting tools to reduce energy consumption, improve machining quality, and develop sustainable wood manufacturing.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:CNC freze · Kesme gücü · İşleme parametreleri

Abstract

This study focused on the influence of machining parameters and wood properties on cutting power in the CNC milling of Oriental beech and Scots pine. The results indicated that the statistical models were highly significant (p < 0.001) with explanatory powers of 82.5% for Oriental beech and 87.2% for Scots pine. The cutting power of Oriental beech was greater than that of Scots pine because of the higher density and compact structure of Oriental beech. The order of importance of the machining parameters on the cutting power was spindle speed, depth of cut, feed rate, and cutting direction for both species, respectively. Width of cut had a greater effect on Scots pine than on Oriental beech. The species-specific machining behavior was observed between Oriental beech and Scots pine, and cutting power generally increased with increasing spindle speed, feed rate, and depth of cut. There were significant interactions between the machining parameters, especially feed rate × depth of cut and spindle speed × width of cut, which suggested that the machining parameters should be optimized as a whole instead of individually. Therefore, the findings of this study could help to select suitable cutting conditions and maintain the sharpness of cutting tools to reduce energy consumption, improve machining quality, and develop sustainable wood manufacturing.

Özet

Bu çalışmada, Doğu kayını ve sarıçamın CNC frezelenmesinde işleme parametrelerinin ve odun özelliklerinin kesme gücü üzerindeki etkisine odaklanılmıştır. Sonuçlar, istatistiksel modellerin son derece anlamlı olduğunu (p < 0,001) ve modellerin açıklayıcılık gücünün Doğu kayını için %82,5, sarıçam için %87,2 olduğunu göstermiştir. Doğu kayınının kesme gücü, yüksek yoğunluğu ve kompakt yapısı nedeniyle sarıçamdan daha yüksek çıkmıştır. Her iki tür için de işleme parametrelerinin kesme gücü üzerindeki önem sırası sırasıyla; devir, kesme derinliği, besleme hızı ve kesme yönü şeklinde olmuştur. Kesiş genişliği, sarıçam üzerinde kayına göre daha büyük bir etki göstermiştir. Doğu kayını ve sarıçam arasında türe özgü işleme davranışları gözlemlenmiş ve kesme gücü genel olarak devir, besleme hızı ve kesiş derinliğindeki artışla birlikte artmıştır. İşleme parametreleri arasında, özellikle besleme hızı × kesiş derinliği ve devir × kesiş genişliği arasında önemli etkileşimler olduğu görülmüştür. Bu durum, işleme parametrelerinin tek tek değil, bir bütün olarak optimize edilmesi gerektiğini ortaya koymuştur. Bu nedenle, bu çalışmanın bulguları; enerji tüketimini azaltmak, işleme kalitesini artırmak ve sürdürülebilir ahşap üretimini geliştirmek için uygun işleme koşullarının seçilmesine ve kesici takım keskinliğinin korunmasına yardımcı olabilir.

🔖

Cite This Article

Cakmak, A. (2026). Effects of Some Machining Parameters on Cutting Power in CNC Milling of Oriental Beech (Fagus orientalis L.) and Scots pine (Pinus sylvestris L.) woods. Artvin Çoruh Üniversitesi Orman Fakültesi Dergisi, Cilt: 27 Sayı: 4, 1–14. https://doi.org/10.17474/artvinofd.1989109

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (47)

  1. Atanasov, V. (2021). Experimental research on the cutting force during longitudinal milling of solid wood and wood-based composites. Acta Facultatis Xylologiae Zvolen res Publica Slovaca, 63(2), 73-84. https://doi.org/10.17423/afx.2021.63.2.06
  2. Ayari, O., Bouali, A., & Méausoone, P.J. (2020). Cutting forces and accuracy characterization during wood machining with serial robots. European Journal of Wood and Wood Products, 78(4), 767-775. https://doi.org/10.1007/s00107-020-01539-4
  3. Bal, B.C., Mengeloğlu, F., Akçakaya, E., & Gündeş, Z. (2022). Effects of cutter parameters on surface roughness of fiberboard and energy consumption of CNC machine. Kastamonu University Journal of Forestry Faculty, 22(3), 264-272. https://doi.org/ 10.17475/kastorman.1215347
  4. Caceres, C. B., Uliana, L., & Hernández, R.E. (2018). Orthogonal cutting study of wood and knots of white spruce. Wood Fiber Science, 50(1), 55-65. https://doi.org/10.22382/wfs-2018-006
  5. Cakmak, A. (2022). Odun ve odun kökenli malzemelerde işleme mekaniklerini etkileyen faktörler. Turkish Journal of Forest Science, 6(2), 629-649. https://doi.org/10.32328/turkjforsci.1167080
  6. Cakmak, A., Malkocoglu, A., & Ozsahin, S. (2023). Optimization of wood machining parameters using artificial neural network in CNC router. Materials Science and Technology, 39(14), 1728-1744. https://doi.org/10.1080/02670836.2023.2180901
  7. Chladil, J., Sedlák, J., Rybářová, E.Š., Kučera, M., & Dado, M. (2019). Cutting conditions and tool wear when machining wood-based materials. BioResources, 14(2), 3495-3505. https://doi.org/10.15376/biores.14.2.3495-3505
  8. Chuchala, D., Orlowski, K.A., Sandak, A., Sandak, J., Pauliny, D., & Barański, J. (2014). The effect of wood provenance and density on cutting forces while sawing Scots pine (Pinus sylvestris L.). BioResources, 9(3), 5349-5361. https://doi.org/10.15376/biores.9.3.5349-5361
  9. Cristóvão, L. (2013). Machining properties of wood: tool wear, cutting force and tensioning of blades (Doctoral Thesis). Luleå Tekniska Universitet, Skellefteå, Sweden.
  10. Curti, R., Marcon, B., Denaud, L., & Collet, R. (2018). Effect of grain direction on cutting forces and chip geometry during green beech wood machining. BioResources, 13(3), 5491-5503. https://doi.org/10.15376/biores.13.3.5491-5503
  11. Curti, R., Marcon, B., Denaud, L., Togni, M., Furferi, R., & Goli, G. (2021). Generalized cutting force model for peripheral milling of wood, based on the effect of density, uncut chip cross section, grain orientation and tool helix angle. European Journal of Wood and Wood Products, 79(3), 667-678. https://doi.org/10.1007/s00107-021-01667-5
  12. Çakıroğlu, E.O., Demir, A., Aydın, İ., & Büyüksarı, Ü. (2022). Prediction of optimum CNC cutting conditions using artificial neural network models for the best wood surface quality, low energy consumption, and time savings. BioResources, 17(2), 2501-2524. https://doi.org/10.15376/biores.17.2.2501-2524
  13. Dado, M., Koleda, P., Vlašic, F., & Salva, J. (2025). Investigation of the applicability of acoustic emission signals for adaptive control in CNC wood milling. Applied Sciences, 15(12), 6659. https://doi.org/10.3390/app15126659
  14. Demir, A., Cakiroglu, E.O., & Aydin, I. (2022). Determination of CNC processing parameters for the best wood surface quality via artificial neural network. Wood Material Science & Engineering, 17(6), 685-692. https://doi.org/10.1080/17480272.2021.1929466
  15. Demirci, S. (2013). Effect of the number of knives, feed rate and cutting depth on surface roughness of some wood species processed with planer. Kastamonu University Journal of Forestry Faculty, 13(1), 84-99.
  16. Dong, W., Xiong, X., Ma, Y., & Yue, X. (2021). Woodworking tool wear condition monitoring during milling based on power signals and a particle swarm optimization-back propagation neural network. Applied Sciences, 11(19), 9026. https://doi.org/10.3390/app11199026
  17. Durković, M., & Danon, G. (2017). Comparison of measured and calculated values of cutting forces in oak wood peripheral milling. Wood Research, 62(2), 293-306.
  18. Fekiač, J., Svoreň, J., Gáborík, J., & Němec, M. (2022). Reducing the energy consumption of circular saws in the cutting process of plywood. Coatings, 12(1), 55. https://doi.org/10.3390/coatings12010055
  19. Feng, J., Zhu, J., Guo, M., Li, X., & Wang, X. (2026). Efficient prediction of cutting force and stability in five-axis machining of complex surfaces based on dimensional compression. Journal of Manufacturing and Materials Processing, 10(6), 213. https://doi.org/10.3390/jmmp10060213
  20. Goli, G., Bléron, L., Marchal, R., Uzielli, L., & Negri, M. (2002). Measurment of cutting forces in routing wood at varous grain angles: initial results with Douglas-fir. Wood Science Engineering in the Third Millennium, 123-130.
  21. Goli, G., Curti, R., Marcon, B., Scippa, A., Campatelli, G., Furferi, R., & Denaud, L. (2018). Specific cutting forces of isotropic and orthotropic engineered wood products by round shape machining. Materials, 11(12), 2575. https://doi.org/10.3390/ma11122575
  22. Guedes, T.O., Moreira da Silva, J.R., Hein, P.R.G., & Ferreira, S.C. (2020). Cutting energy required during the mechanical processing of wood species at different drying stages. Maderas. Ciencia Y Tecnología, 22(4), 477- 482. https://doi.org/10.4067/S0718-221X2020005000406
  23. Hanincová, L., Procházka, J., & Novák, V. (2024). Comparative analysis of cutting forces in CNC milling of MDF: the role of tool coatings, cutting speed, and feed per tooth. Coatings, 14(9), 1085. https://doi.org/10.3390/coatings14091085
  24. Hortobágyi, Á., Koleda, P., Koleda, P., & Kminiak, R. (2023). Effect of milling parameters on amplitude spectrum of vibrations during milling materials based on wood. Applied Sciences, 13(8), 5061. https://doi.org/10.3390/app13085061
  25. Huang, Y., Chuchala, D., Buck, D., Orlowski, K.A., Fredriksson, M., & Svensson, M. (2024). Analysis of the relationship between cutting forces and local structural properties of Scots pine wood aided by computed tomography. The International Journal of Advanced Manufacturing Technology, 135(9), 4975-4987. https://doi.org/10.1007/s00170-024-14797-w
  26. Jiang, S., Buck, D., Tang, Q., Guan, J., Wu, Z., Guo, X., Zhu, Z., & Wang, X. (2022). Cutting force and surface roughness during straight-tooth milling of Walnut wood. Forests, 13(12), 2126. https://doi.org/10.3390/f13122126
  27. Koleda, P., Barcík, Š., Svoreň, J., Naščák, Ľ., & Dobrík, A. (2019). Influence of cutting wedge treatment on cutting power, machined surface quality, and cutting edge wear when plane milling oak wood (cutting edge wear; cutting power; plane milling; surface roughness). BioResources, 14(4), 9271-9286. https://doi.org/10.15376/biores.14.4.9271-9286
  28. Koleda, P., Čuchor, T., Koleda, P., & Rajko, Ľ. (2024). Prediction models for the milling of heat-treated beech wood based on the consumption of energy. Applied Sciences, 14(20), 9539. https://doi.org/https://doi.org/10.3390/app14209539
  29. Kopecký, Z., Hlásková, L., Solař, A., & Nesázal, P. (2019). Cutting forces in quasi-orthogonal CNC milling. Wood Research, 64(5), 879-890.
  30. Krenke, T., Frybort, S., & Müller, U. (2018). Cutting force analysis of a linear cutting process of spruce. Wood Material Science & Engineering, 13(5), 279-285. https://doi.org/10.1080/17480272.2017.1324916
  31. Kubš, J., Gašparík, M., Gaff, M., Kaplan, L., Čekovská, H., Ježek, J., & Štícha, V. (2017). Influence of thermal treatment on power consumption during plain milling of Lodgepole pine (Pinus contorta subsp. murrayana) (plain milling; thermal treatment; cutting power; lodgepole pine; cutting speed; feed speed; rake angle). BioResources, 12(1), 407-418. https://doi.org/10.15376/biores.12.1.407-418
  32. Li, R., Yang, F., & Wang, X. (2022). Modeling and predicting the machined surface roughness and milling power in Scot’s pine helical milling process. Machines, 10(331), 1-13. https://doi.org/10.3390/machines10050331
  33. Li, R., Yao, Q., Xu, W., Li, J., & Wang, X.A. (2022). Study of cutting power and power efficiency during straight-tooth cylindrical milling process of particle boards. Materials, 15(3), 879. https://doi.org/10.3390/ma15030879
  34. Malkocoglu, A. (2007). Machining properties and surface roughness of various wood species planed in different conditions. Building and Environment, 42(7), 2562-2567. https://doi.org/10.1016/j.buildenv.2006.08.028
  35. Marchal, R., Mothe, F., Denaud, L.-E., Thibaut, B., & Bleron, L. (2009). Cutting forces in wood machining–basics and applications in industrial processes. a review. COST Action E35 2004-2008: Wood machining - Micromechanics and fracture, Holzforschung, 63(2), 157-167. https://doi.org/10.1515/HF.2009.014
  36. Meng, Y., Dong, S., Sun, X., Wei, S., & Liu, X. (2024). Cutting energy consumption modeling by considering tool wear and workpiece material properties for Multi-Objective optimization of machine tools. Coatings, 14(6), 691. https://doi.org/10.3390/coatings14060691
  37. Nasir, V., & Cool, J. (2019). Optimal power consumption and surface quality in the circular sawing process of Douglas-fir wood. European Journal of Wood and Wood Products, 77(4), 609-617. https://doi.org/10.1007/s00107-019-01412-z
  38. Orlowski, K.A., Ochrymiuk, T., Hlaskova, L., Chuchala, D., & Kopecky, Z. (2020). Revisiting the estimation of cutting power with different energetic methods while sawing soft and hard woods on the circular sawing machine: A Central European case. Wood Science and Technology, 54(2), 457-477. https://doi.org/10.1007/s00226-020-01162-9
  39. Piernik, M., Pinkowski, G., & Krauss, A. (2023). Effect of chip thickness, wood cross-sections, and cutting speed on surface roughness and cutting power during up-milling of beech wood. BioResources, 18(4), 6784-6801. https://doi.org/10.15376/biores.18.4.6784-6801
  40. Pimenov, D.Y., Der, O., Patel, G.M., Giasin, K., & Ercetin, A. (2025). State-of-the-art review of energy consumption in machining operations: challenges and trends. Renewable and Sustainable Energy Reviews, 224, December 2025, 116073. https://doi.org/10.1016/j.rser.2025.116073
  41. Pinkowski, G., Piernik, M., Wołpiuk, M., & Krauss, A. (2024). Effect of chip thickness and tool wear on surface roughness and cutting power during up-milling wood of different density. BioResources, 19(4), 9234–9248. https://doi.org/10.15376/biores.19.4.9234-9248
  42. TS ISO. (2021). 13061-2, Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 2: Determination of density for physical and mechanical tests. Ankara, Türkiye: TSE.
  43. Wang, J., Wu, Z., Zhang, F., Song, C., Hu, W., Zhu, Z., Guo, X., & Cao, P. (2024). Research on the end-milling surface quality of paulownia based on response surface model in terms of force and chip morphology. Forests, 15(2), 325. https://doi.org/10.3390/f15020325
  44. Xu, W., Wu, Z., Lu, W., Yu, Y., Wang, J., Zhu, Z., & Wang, X. (2022). Investigation on cutting power of wood–plastic composite using response surface methodology. Forests, 13(9), 1397. https://doi.org/10.3390/f13091397
  45. Yao, T.X., & Boh, T.K. (2019). Energy reduction by optimizing sharpness angle and feed per knife in wood planing operation. International Journal of Agriculture, 8(June), 40-47.
  46. Yu, Y., Buck, D., Yang, H., Du, X., Song, M., Wang, J., & Zhu, Z. (2023a). Cutting power, temperature, and surface roughness: a multiple target assessment of beech during diamond milling. Forests, 14, 1163. https://doi.org/10.3390/f14061163
  47. Yu, Q., Pan, X., Yang, Z., Zhang, L., & Cao, J. (2023b). Effects of the surface roughness of six wood species for furniture production on the wettability and bonding quality of coating. Forests, 14(5), 996. https://doi.org/10.3390/f14050996