Journals / Sağlık Bilimleri Dergisi / 2017 / Cilt: 26 - Sayı: 1

Evalution of Stress Amounts on Different Length Cylindric Implants via Finite Element Analysis

FARKLI UZUNLUKTAKİ SİLİNDİRİK İMPLANTLARDA OLUŞAN STRES MİKTARININ SONLU ELEMANLAR ANALİZİ İLE İNCELENMESİ

Pages
64–70
Publication Date
2017-03-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In conclusion, the length is not a main factor to determine the stress levels on the implants and bone in 8 and 10 mm length cylindric implants.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The aim of this study was to investigate stress amounts on different length cylindric implants with finite element analysis.
📊
Key Findings & Data:In our study 3,2 mm diameter 8 mm and 10 mm length cylindric implants were compared.
💡
Conclusion & Impact:In conclusion, the length is not a main factor to determine the stress levels on the implants and bone in 8 and 10 mm length cylindric implants.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Silindirik implantlar · sonlu elemanlar analizi · biyomekanik analiz

Abstract

The aim of this study was to investigate stress amounts on different length cylindric implants with finite element analysis. In our study 3,2 mm diameter 8 mm and 10 mm length cylindric implants were compared. We analyzed stress-strain amounts of implants and bone, under 150 N oblique loads with finite element analysis. According to finite element analysis results, Von Mises stres on implants were within durability limits of grade 4 titanium. However, strain amounts on bone were out of range according to the Frost’s “Mekanostat” theory . In conclusion, the length is not a main factor to determine the stress levels on the implants and bone in 8 and 10 mm length cylindric implants.

Özet

Bu çalışmanın amacı, eşit yükler altında farklı uzunluktaki silindirik implantlarda oluşan stres dağılımının sonlu elemanlar stres analizi ile değerlendirilmesidir. Çalışmamızda 3,2 mm çapında 8 mm ve 10 mm uzunluğunda silindirik implantlar karşılaştırılmıştır. Çalışmamızda sonlu elemanlar stres analizi ile 150 N oblik yük altında implantlarda ve kemikte oluşan stres- gerinim miktarları incelenmiştir. Sonlu elemanlar analizi sonuçlarına bakıldığında; implantlar üzerinde oluşan Von Mises stresin istenilen aralıkta olduğu ve 4. sertlik titanyumun dayanım sınırları içerinde yer aldığı fakat kemikte oluşan asal gerinim miktarının ise Frost’un “Mekanostat” teorisinde belirtilen sınırlardan yüksek olduğu gözlenmiştir. Sonuç olarak 8 ve 10 mm uzunluğa sahip silindirik implantlarda, aradaki uzunluk farkının ne implantlarda ne de kemikte oluşan stres miktarını önemli ölçüde etkilemediği görülmüştür.

🔖

Cite This Article

YAŞAR, M. T., KILIÇ, E., ALKAN, A. (2017). Evalution of Stress Amounts on Different Length Cylindric Implants via Finite Element Analysis. Sağlık Bilimleri Dergisi, Cilt: 26 - Sayı: 1, 64–70. https://ajindex.com/articles/155417

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (11)

  1. Testori T, Weinstein R, Wallace S. Maxillary sinus surgery and alternatives in treatment, Quintessence Publishing Co, London, 2009.
  2. Renouard F, Nisand D. Impact of implant length and diameter on survival rates. Clin Oral Implants Res 2006; 17(S2): 35-51.
  3. Chen ST, Buser D. Clinical and esthetic outcomes of implants placed in postextraction sites. Int J Oral Maxillofac Implants 2009;24: 13-18.
  4. Block MS, Kent JN. Sinus augmentation for dental implants: The use of autogenous bone. J Oral Maxillofac Surg 1997; 55(11): 1281-1286.
  5. Stevens P, Fredrickson E, Gres M. Implant prosthodontics: Clinical and laboratory procedures, Mosby, St Louis, 1994: 35. Friberg B, Ekestubbe A, Sennerby L. Clinical Outcome of Brånemark System Implants of Various Diameters: A Retrospective Study. Int J Oral Maxillofac 2002; 17(5): 32-38.
  6. Gotfredsen K, Karlsson U. A prospective 5‐year study of fixed partial prostheses supported by implants with machined and TiO2‐blasted surface. J Prosthodont 2001; 10(1): 2-7.
  7. Baggi L, Cappelloni I, Di Girolamo M, Maceri F, Vairo G. The influence of implant diameter and length on stress distribution of osseointegrated implants related to crestal bone geometry: A three -dimensional finite element analysis. J Prosthet Dent 2008; 100(6): 422-431.
  8. Chun HJ, Cheong SY, Han JH, et al. Evaluation of design parameters of osseointegrated dental implants using finite element analysis. J Oral Rehabil 2002; 29(6): 565-574.
  9. Hansson S, Werke M. The implant thread as a retention element in cortical bone: The effect of thread size and thread profile: A finite element study. J Biomech 2003; 36(9): 1247-1258. Frost HM. A 2003 update of bone physiology and Wolff's Law for clinicians. Angle Orthod 2004; 74 (1): 3-15. Frost HM. Bone “mass” and the “mechanostat”: A proposal. Anatomic Rec 1987; 219(1): 1-9.
  10. Frost HM. The laws of bone structure, CC Thomas, Springfield, 1964.
  11. Romeo E, Lops D, Amorfini L, Chiapasco M, Ghisolfi M, Vogel G. Clinical and radiographic evaluation of small‐diameter (3.3‐mm) implants followed for 1–7 years: A longitudinal study. Clin Oral Implants Res 2006; 17(2): 139-148. Weinberg LA. The biomechanics of force distribution in implant-supported prostheses. Int J Oral Maxillofac Implants 1993; 8(1): 33-58. Kirsch A. The IMZ endosseous two phase implant system: a complete oral rehabilitation treatment concept. J Oral Implantol 1986; 12: 576-589. Lavelle CL. Biomechanical considerations of prosthodontic therapy: The urgency of research into alveolar bone r