Journals / DSİ Teknik Bülteni / 2018 / Sayı: 128

DETERMINATION OF A FORCE ACTING ON A PELTON TURBINE BUCKET FOR A VARIETY OF JET VELOCITY AND SPLITTER ANGLES USING COMPUTATIONAL FLUID DYNAMICS

HESAPLAMALI AKIŞKANLAR DİNAMİĞİ KULLANILARAK ÇEŞİTLİ JET HIZLARI VE AYIRICI AÇILARI İÇİN BİR PELTON TÜRBİN KEPÇESİNE ETKİ EDEN KUVVETLERİN BELİRLENMESİ

Pages
11–21
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

It was revealed that there was a linear relationship between force on the bucket and jet inlet velocity; therefore, a higher force on the bucket could be obtained for higher jet velocities for both Models 1 and 2.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In the present study, the two-phase flow volume of fluid approach was utilized in a numerical analysis performed with the ANSYS-Fluent program.
📊
Key Findings & Data:The study utilized two diverse bucket models at various inlet velocities of 20, 25, 30, 35 and 40 m/s, four diverse splitter angles of 55, 75, 90 and 115° and two jet diameters of 30 and 40 mm for the identification of every single parameter’s impact on the effective force generated on the bucket surface.
💡
Conclusion & Impact:It was revealed that there was a linear relationship between force on the bucket and jet inlet velocity; therefore, a higher force on the bucket could be obtained for higher jet velocities for both Models 1 and 2.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In the present study, the two-phase flow volume of fluid approach was utilized in a numerical analysis performed with the ANSYS-Fluent program. The effects of bucket splitter angles, inlet velocity values and jet diameters of two different bucket-shape models were investigated to determine the force existed on the Pelton turbine bucket for the evaluation of power generation. The study utilized two diverse bucket models at various inlet velocities of 20, 25, 30, 35 and 40 m/s, four diverse splitter angles of 55, 75, 90 and 115° and two jet diameters of 30 and 40 mm for the identification of every single parameter’s impact on the effective force generated on the bucket surface. It was revealed that there was a linear relationship between force on the bucket and jet inlet velocity; therefore, a higher force on the bucket could be obtained for higher jet velocities for both Models 1 and 2.

Özet

Bu çalışmada, ANSYS-Fluent programı ile gerçekleştirilen sayısal analizlerde iki fazlı akışkan ile akış hacim modeli kullanılmıştır. Güç üretiminin değerlendirilmesi için Pelton türbin kepçesinde mevcut olan kuvveti belirlemek amacıyla, iki farklı kepçe şeklindeki modelin kepçe ayırıcı açıları, giriş hız değerleri ve jet çapları üzerindeki etkileri araştırılmıştır. Her bir parametrenin, kepçe yüzeyinde oluşturduğu kuvvetin üzerindeki etkisinin belirlenmesi için çalışmada; 20, 25, 30, 35 ve 40 m / s'lik çeşitli giriş hızlarındaki iki farklı kova modelinin 55, 75, 90 ve 115 ° 'lik dört farklı ayırıcı açısına sahip 30 ve 40 mm'lik iki jet çapı kullanmıştır. Kova üzerindeki kuvvet ve jet giriş hızı arasında doğrusal bir ilişki olduğu ortaya çıkmıştır; bu nedenle Model 1 ve 2 için daha yüksek jet hızları için kova üzerinde daha yüksek bir kuvvetin elde edilebileceği sonucuna ulaşılmıştır.

🔖

Cite This Article

YAYLA, S., ABDULLAH, A., ORUÇ, M. (2018). DETERMINATION OF A FORCE ACTING ON A PELTON TURBINE BUCKET FOR A VARIETY OF JET VELOCITY AND SPLITTER ANGLES USING COMPUTATIONAL FLUID DYNAMICS. DSİ Teknik Bülteni, Sayı: 128, 11–21. https://ajindex.com/articles/150611

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (15)

  1. Barstad, L.F., ‘’CFD analysis of a Pelton turbine’’, Master of Science in Product Design Manufacturing, Norwegian University of Science and Technology, 2012
  2. Noor, A.I., ‘’Modeling of micro-hydroelectric system design’’, Faculty of Electrical and Electronic Engineering University Tun Hussein Onn Malaysia, 2012
  3. George, N.J., Sabu, S., Joseph, K.R., Alex, A.C., ‘’Static analysis on Pelton wheel bucket structural deformation and material property study’’, International Journal of Engineering Research & Technology, 3, p. 2278-0181, 2014
  4. Hana, M.A., ‘’Discussion on numerical simulation in Pelton turbines’’, Proceedings of 19th IAHR Symposium, Singapore, Sept. 9–11, and Paper Presented at SingaporeWorld Scientific, p. 306–315, 1998
  5. Sick, M., Keck, H., Parkinson, E., Vullioud, G., ‘’New challenges in Pelton research’’, Paper presented at Hydro 2000
  6. Conference, Bern Switzerland, 2000.
  7. Janetzky, B., Göde E., Ruprecht A., Keck H., Schärer C., ‘’Numerical simulation of the flow in a Pelton bucket’’, Paper Presented at Proceedings of 19th IAHR Symposium, Singapore, Sept. 9–11, p. 276–284, 1998
  8. Mack, R., Moser, W., ‘’Numerical investigations of the flow in a Pelton turbine’’, Proceedings of XXI st IAHR Symposium on Hydraulic Machinery and Systems, Sept. 9–12,
  9. Lausanne, Laboratory For Hydraulic Machines, Lausanne, p. 373–378, 2002
  10. Gotfred, S.B., ‘’Numerical analysis of the two-phase Pelton jet flow using a single-phase model and analytical discussions of the Pelton jet surface break-up phenomenon’’, Ph.D. thesis, Norwegian University of Science and Technology, 2003
  11. Zoppe, B., Pellone, C., Maitre, T., Leroy, P., ‘’Flow analysis inside a Pelton turbine bucket ‘’, Journal of Turbomachinery, 128, p. 500-511, 2006
  12. Gupta, V., Prasad, V., ‘’Numerical investigations for jet flow characteristics on Pelton turbine bucket ’’, International Journal of Emerging Technology and Advanced Engineering, 2, p. 2250-2459, 2012
  13. Kvicinsky, S., ‘’Méthoded’analysedesécoulements 3d à surface libre application auxturbinespelton [j], EcolePolytechnique Fédérale de Lausanne, p. 2526, 2002
  14. Pudasaini, S., Neopane, H.P., Panthee, A., Pathak, A., Chaudhary, B.B., ‘’Computational fluid dynamic analysis of Pelton runner of khimti hydropower project of Nepal’’, Paper Presented at Reattach Symposium Compendium, 4, p. 91-94, 2014
  15. Yadav, S., ‘’Some aspects of performance improvement of Pelton wheel turbine with reengineered blade and auxiliary attachments‘’, International Journal of Scientific and Engineering