SavedAdd your journal

Journals / İmalat Teknolojileri ve Uygulamaları / 2026 / Cilt: 7 Sayı: 2

Optimization and Prediction of Mechanical Properties of PLA: Effects of Infill Pattern, Printing Temperature and Annealing Duration Using Taguchi and Artificial Neural Networks

PLA'nın Mekanik Özelliklerinin Optimizasyonu ve Tahmini: Taguchi ve Yapay Sinir Ağları Kullanılarak Dolgu Deseni, Baskı Sıcaklığı ve Tavlama Süresinin Etkileri

İsmail Aykut Karamanlı(BOZOK UNIVERSITY, SORGUN VOCATIONAL SCHOOL)0000-0002-6725-2662
Pages
79–92
Publication Date
2026-08-30
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results indicated that the highest tensile strength was achieved with sample H-230-90 at 45.33 MPa.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This study experimentally and statistically examined the effects of infill pattern, printing temperature, and annealing duration on the mechanical properties of PLA tensile samples produced using the fused filament fabrication method (FFF).
📊
Key Findings & Data:The samples were produced in three different infill patterns (grid, zigzag, and honeycomb) and at two different printing temperatures (200 and 230 ℃).
💡
Conclusion & Impact:The results indicated that the highest tensile strength was achieved with sample H-230-90 at 45.33 MPa.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Eklemeli İmalat · Mekanik özellikler · Çekme dayanımı

Abstract

This study experimentally and statistically examined the effects of infill pattern, printing temperature, and annealing duration on the mechanical properties of PLA tensile samples produced using the fused filament fabrication method (FFF). The samples were produced in three different infill patterns (grid, zigzag, and honeycomb) and at two different printing temperatures (200 and 230 ℃). The samples were annealed for 90 and 180 minutes according to the experimental design created using the DoE (Design of Experiment) approach. The surface hardness of the samples was measured and tensile tests were performed. The results were analyzed using Taguchi and ANOVA methods, so that the values and parameters effective on the results and obtaining the optimum results were determined. Additionally, a prediction model was created using the Artificial Neural Network method (ANN). Control samples were produced under different manufacturing parameters and tested. The accuracy of the model was tested by comparing the experimental results to the predicted values. The results indicated that the highest tensile strength was achieved with sample H-230-90 at 45.33 MPa. The honeycomb achieves the highest tensile strength and hardness values due to its homogeneous stress distribution, while zigzag patterned samples exhibit the highest ductility. It was found that the annealing process increased tensile strength and surface hardness, but decreased elongation. According to the ANOVA results, the most effective parameter on tensile strength was the infill pattern with 96.06%. The model yielded successful results in predicting grid and zigzag infill pattern samples but had high error rates in predicting honeycomb samples.

Özet

Bu çalışmada, ergimiş filament imalatı (FFF) yöntemi kullanılarak üretilen PLA çekme numunelerinin mekanik özelliklerinin dolgu deseni, baskı sıcaklığı ve tavlama süresi değişimine göre etkileri deneysel ve istatistiksel olarak incelenmiştir. Numuneler üç farklı dolgu deseni (ızgara, zikzak ve bal peteği) ve iki farklı baskı sıcaklığında (200 ve 230 ℃) üretilmiştir. Numuneler, DoE (Deney Tasarımı) yaklaşımı kullanılarak oluşturulmuş ve yine deney tasarımına göre 90 ve 180 dakika tavlanmıştır. Numunelerin yüzey sertliği ölçülmüş, çekme testleri yapılmış ve gerilme-gerinim eğrilerinden tokluk değerleri hesaplanmıştır. Sonuçlar Taguchi ve ANOVA yöntemleri kullanılarak analiz edilmiş, böylece sonuçlar üzerinde etkili olan ve optimum sonuçların elde edilmesini sağlayan değerler ve parametreler belirlenmiştir. Ek olarak, Yapay Sinir Ağları (YSA) yöntemi kullanılarak bir tahmin modeli oluşturulmuştur. Farklı üretim parametreleri ile kontrol numuneleri üretilmiş ve test edilmiştir. Modelin doğruluğu, deney sonuçları ile tahmin edilen değerler karşılaştırılarak test edilmiştir. Sonuçlar, en yüksek çekme mukavemetinin 45.33 MPa ile H-230-90 numunesi ile elde edildiğini göstermiştir. Bal peteği desenli numunelerde homojen gerilme dağılımları nedeniyle en yüksek çekme mukavemeti ve sertlik değerlerini elde ederken, zikzak desenli numuneler en yüksek süneklik ve tokluk performansını sergilemiştir. Tavlama işleminin çekme mukavemetini ve yüzey sertliğini artırdığı, ancak uzamayı azalttığı bulunmuştur. ANOVA sonuçlarına göre, çekme mukavemeti üzerinde en etkili parametre %96.06 ile dolgu deseni olmuştur. Model, ızgara ve zikzak dolgu desenli numunelerin tahmininde başarılı sonuçlar vermiş, ancak bal peteği numuneleri için yüksek tahmin hataları elde edilmiştir.

🔖

Cite This Article

Karamanlı, İ. A. (2026). Optimization and Prediction of Mechanical Properties of PLA: Effects of Infill Pattern, Printing Temperature and Annealing Duration Using Taguchi and Artificial Neural Networks. İmalat Teknolojileri ve Uygulamaları, Cilt: 7 Sayı: 2, 79–92. https://doi.org/10.52795/mateca.1949982

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (42)

  1. S. Bhandari, R.A. Lopez-Anido, D.J. Gardner, Enhancing the interlayer tensile strength of 3D printed short carbon fiber reinforced PETG and PLA composites via annealing, Addit. Manuf. 30 (2019) 100922. https://doi.org/10.1016/j.addma.2019.100922.
  2. F. Kartal, A. Kaptan, Effects of annealing temperature and duration on mechanical properties of PLA plastics produced by 3D Printing, Eur. Mech. Sci. 7 (2023) 152–159. https://doi.org/10.26701/ems.1290961.
  3. İ.A. Karamanlı, V. Neccaroğlu, Influence of Printing Parameters on Flexural Strength and Hardness Properties of PLA-CF Composites: An Experimental and Statistical Approach, İmalat Teknol. ve Uygulamaları 6 (2025) 272–286. https://doi.org/10.52795/mateca.1724130.
  4. S. Dağlı, Investigation of the Bonding Performance of Parts Produced by FDM and SLA 3D Printing Methods, İmalat Teknol. ve Uygulamaları 6 (2025) 100–110. https://doi.org/10.52795/mateca.1635653.
  5. Y. Srithep, P. Nealey, L.-S. Turng, Effects of annealing time and temperature on the crystallinity and heat resistance behavior of injection‐molded poly(lactic acid), Polym. Eng. Sci. 53 (2013) 580–588. https://doi.org/10.1002/pen.23304.
  6. Z. Kaya, B. Aksoy, K. Özsoy, Eklemeli İmalat Yöntemiyle Üretilen Altı Eksenli Robot Kol ile Görüntü İşleme ve Yapay Zeka Tabanlı Ürünlerin Tasniflemesi, J. Mater. Mechatronics A 4 (2023) 193–210. https://doi.org/10.55546/jmm.1256366.
  7. A.R. de M. Costa, C.B.B. Luna, E.P. do Nascimento, E. da S.B. Ferreira, C. de M. Costa, Y.M.B. de Almeida, E.M. Araújo, Tailoring PLA/ABS Blends Compatibilized with SEBS-g-MA through Annealing Heat Treatment, Polymers (Basel). 15 (2023) 3434. https://doi.org/10.3390/polym15163434.
  8. J. Liesenfeld, J.J. Jablonski, J.R.F. da Silva, A.A. Buenos, C.J. Scheuer, Impact of annealing on the characteristics of 3D-printed graphene-reinforced PLA composite, J. Manuf. Process. 128 (2024) 133–157. https://doi.org/10.1016/j.jmapro.2024.08.025.
  9. A. Zennaki, L. Zair, K. Arabeche, L. Benkraled, U. Maschke, A. Berrayah, Effect of annealing on thermal and dynamic mechanical properties of poly(lactic acid), J. Appl. Polym. Sci. 139 (2022) e53095. https://doi.org/10.1002/app.53095.
  10. M. Pastorek, A. Kovalcik, Effects of thermal annealing as polymer processing step on poly(lactic acid), Mater. Manuf. Process. 33 (2018) 1674–1680. https://doi.org/10.1080/10426914.2018.1453153.
  11. V. Slavković, B. Hanželič, V. Plesec, S. Milenković, G. Harih, Thermo-Mechanical Behavior and Strain Rate Sensitivity of 3D-Printed Polylactic Acid (PLA) below Glass Transition Temperature (Tg), Polymers (Basel). 16 (2024) 1526. https://doi.org/10.3390/polym16111526.
  12. Y.C. Niranjan, S. Krishnapillai, R. Velmurugan, S.K. Ha, Effect of Annealing Time and Temperature on Dynamic Mechanical Properties of FDM Printed PLA BT - Composite Materials for Extreme Loading, in: S. Krishnapillai, V. R., S.K. Ha (Eds.), Springer Singapore, Singapore, 2022: pp. 143–160.
  13. Ç. Kahya, O. Tunçel, O. Çavuşoğlu, K. Tüfekci, Thermal annealing optimization for improved mechanical performance of PLA parts produced via 3D printing, Polym. Test. 144 (2025) 108735. https://doi.org/10.1016/j.polymertesting.2025.108735.
  14. T. Tabi, I.E. Sajo, F. Szabo, A.S. Luyt, J.G. Kovacs, Crystalline structure of annealed polylactic acid and its relation to processing, Express Polym. Lett. 4 (2010) 659–668. https://doi.org/10.3144/expresspolymlett.2010.80.
  15. M. Behzadnasab, A.A. Yousefi, D. Ebrahimibagha, F. Nasiri, Effects of processing conditions on mechanical properties of PLA printed parts, Rapid Prototyp. J. 26 (2019) 381–389. https://doi.org/10.1108/RPJ-02-2019-0048.
  16. M.U. Alabd, A. Temiz, Optimization of Annealing and 3D Printing Process Parameters of PLA Parts, Int. J. 3D Print. Technol. Digit. Ind. 8 (2024) 185–201. https://doi.org/10.46519/ij3dptdi.1451666.
  17. S. Yaisun, T. Trongsatitkul, PLA-Based Hybrid Biocomposites: Effects of Fiber Type, Fiber Content, and Annealing on Thermal and Mechanical Properties, Polymers (Basel). 15 (2023) 4106. https://doi.org/10.3390/polym15204106.
  18. İ.A. Karamanlı, K. Tahnal, Optimization of Printing Parameters of PLA and ABS Produced by FFF, J. Mater. Mechatronics A 5 (2024) 286–302. https://doi.org/10.55546/jmm.1566700.
  19. J. Lluch-Cerezo, M.D. Meseguer, J.A. García-Manrique, R. Benavente, Influence of Thermal Annealing Temperatures on Powder Mould Effectiveness to Avoid Deformations in ABS and PLA 3D-Printed Parts, Polymers (Basel). 14 (2022) 2607. https://doi.org/10.3390/polym14132607.
  20. R.A. Wach, P. Wolszczak, A. Adamus‐Wlodarczyk, Enhancement of Mechanical Properties of FDM‐PLA Parts via Thermal Annealing, Macromol. Mater. Eng. 303 (2018) 1800169. https://doi.org/10.1002/mame.201800169.
  21. D.G. Zisopol, A.I. Portoaca, I. Nae, I. Ramadan, A Comparative Analysis of the Mechanical Properties of Annealed PLA, Eng. Technol. Appl. Sci. Res. 12 (2022) 8978–8981. https://doi.org/10.48084/etasr.5123.
  22. N. Jayanth, K. Jaswanthraj, S. Sandeep, N.H. Mallaya, S.R. Siddharth, Effect of heat treatment on mechanical properties of 3D printed PLA, J. Mech. Behav. Biomed. Mater. 123 (2021) 104764. https://doi.org/10.1016/j.jmbbm.2021.104764.
  23. J. Butt, R. Bhaskar, Investigating the Effects of Annealing on the Mechanical Properties of FFF-Printed Thermoplastics, J. Manuf. Mater. Process. 4 (2020) 38. https://doi.org/10.3390/jmmp4020038.
  24. ESUN, ESUN PLA+ Mechanical Properties, (2024). https://www.esun3d.com/tr/pla-pro-product/ (accessed September 24, 2024).
  25. ASTM, ASTM D638-14 Test Method for Tensile Properties of Plastics, (2022). https://doi.org/10.1520/D0638-14.
  26. H. Gürbüz, M.E. Demir, Ş. Baday, İ.H. Akcan, Yapay Sinir Ağı ile Mikro Parçacık Dolgulu Kompozitlerin Tribolojik Özelliklerinin Tahmini, J. Mater. Mechatronics A 6 (2025) 68–82. https://doi.org/10.55546/jmm.1581662.
  27. S. Uslu, M.B. Celik, Prediction of engine emissions and performance with artificial neural networks in a single cylinder diesel engine using diethyl ether, Eng. Sci. Technol. an Int. J. 21 (2018) 1194–1201. https://doi.org/10.1016/j.jestch.2018.08.017.
  28. L. Yu, H. Liu, F. Xie, L. Chen, X. Li, Effect of annealing and orientation on microstructures and mechanical properties of polylactic acid, Polym. Eng. Sci. 48 (2008) 634–641. https://doi.org/10.1002/pen.20970.
  29. P. Janmanee, P. Ratchapakdee, Effect of Annealing on Tensile Strength of 3D Printed PLA with Material Extrusion, Mech. Adv. Compos. Struct. 12 (2025) 465–472. https://doi.org/10.22075/macs.2024.33892.1662.
  30. J. Suder, Z. Bobovsky, Z. Zeman, J. Milotek, M. Vocetka, The Influence of Annealing Temperature on Tensile Strength of Polylactic Acid, MM Sci. J. 2020 (2020) 4132–4137. https://doi.org/10.17973/MMSJ.2020_11_2020048.
  31. C. Zeng, L. Liu, W. Bian, J. Leng, Y. Liu, Compression behavior and energy absorption of 3D printed continuous fiber reinforced composite honeycomb structures with shape memory effects, Addit. Manuf. 38 (2021) 101842. https://doi.org/10.1016/j.addma.2021.101842.
  32. S. Ahn, M. Montero, D. Odell, S. Roundy, P.K. Wright, Anisotropic material properties of fused deposition modeling ABS, Rapid Prototyp. J. 8 (2002) 248–257. https://doi.org/10.1108/13552540210441166.
  33. B.M. Tymrak, M. Kreiger, J.M. Pearce, Mechanical properties of components fabricated with open-source 3-D printers under realistic environmental conditions, Mater. Des. 58 (2014) 242–246. https://doi.org/10.1016/j.matdes.2014.02.038.
  34. A.H. Kadhum, S. Al-Zubaidi, S.S. Abdulkareem, Effect of the Infill Patterns on the Mechanical and Surface Characteristics of 3D Printing of PLA, PLA+ and PETG Materials, ChemEngineering 7 (2023) 46. https://doi.org/10.3390/chemengineering7030046.
  35. C.K. Yeoh, C.S. Cheah, R. Pushpanathan, C.C. Song, M.A. Tan, P.L. Teh, Effect of infill pattern on mechanical properties of 3D printed PLA and cPLA, IOP Conf. Ser. Mater. Sci. Eng. 957 (2020) 012064. https://doi.org/10.1088/1757-899X/957/1/012064.
  36. T.J. Coogan, D.O. Kazmer, Healing simulation for bond strength prediction of FDM, Rapid Prototyp. J. 23 (2017) 551–561. https://doi.org/10.1108/RPJ-03-2016-0051.
  37. Q. Sun, G.M. Rizvi, C.T. Bellehumeur, P. Gu, Effect of processing conditions on the bonding quality of FDM polymer filaments, Rapid Prototyp. J. 14 (2008) 72–80. https://doi.org/10.1108/13552540810862028.
  38. M. Majdak, P. Baranowski, J. Małachowski, Numerical studies of the energy absorption capacities and deformation mechanisms of 2D cellular topologies, Arch. Civ. Mech. Eng. 24 (2024) 111. https://doi.org/10.1007/s43452-024-00926-5.
  39. Ö. Öz, F.H. Öztürk, Yazdırma Açısının 3B Yazıcıda Üretilen PLA Numunenin Mekanik Özellikleri Üzerine Etkisinin Deneysel ve Sonlu Elemanlar Metodu ile İncelenmesi, Politek. Derg. 26 (2023) 529–540. https://doi.org/10.2339/politeknik.882313.
  40. M. Eryıldız, Effect of Build Orientation on Mechanical Behaviour and Build Time of FDM 3d-Printed PLA Parts: An Experimental Investigation, Eur. Mech. Sci. 5 (2021) 116–120. https://doi.org/10.26701/ems.881254.
  41. M.F. Gibson, L. J. and Ashby, Cellular Solids, 2nd ed., Cambridge University Press, Cambridge, 1997.
  42. S. Farah, D.G. Anderson, R. Langer, Physical and mechanical properties of PLA, and their functions in widespread applications — A comprehensive review, Adv. Drug Deliv. Rev. 107 (2016) 367–392. https://doi.org/10.1016/j.addr.2016.06.012.