SavedAdd your journal

Journals / Türkiye Ormancılık Dergisi / 2024 / Cilt: 25 Sayı: 4

Moisture dependent bending properties of poplar

Kavak odununun rutubete bağlı eğilme özellikleri

Tuğba Yılmaz Aydın(Isparta Uygulamalı Bilimler Üniversitesi)0000-0002-6792-9602
Uğur Özkan(Isparta Uygulamalı Bilimler Üniversitesi Orman fakültesi)0000-0003-0147-9976
Pages
514–519
Publication Date
2024-12-28
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The R² values ranged from 0.187 (VLL vs MOR at 85% RH) to 0.94% (VLL vs Edyn at 65% RH).

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The influence of moisture on the physical (density) and mechanical (modulus of rupture-MOR, modulus of elasticity-MOE) properties of Populus x canadensis M. were figured out by three three-point bending tests and ultrasonic testing .
📊
Key Findings & Data:Samples were conditioned at 20±1 °C and 45, 65, and 85% relative humidity.
💡
Conclusion & Impact:The R² values ranged from 0.187 (VLL vs MOR at 85% RH) to 0.94% (VLL vs Edyn at 65% RH).
🔬Design:Araştırma Makalesi
📍Scope:Comprehensive Sample
⚙️Variables:Populus x canadensis · Eğilme direnci · Elastikiyet modülü

Abstract

The influence of moisture on the physical (density) and mechanical (modulus of rupture-MOR, modulus of elasticity-MOE) properties of Populus x canadensis M. were figured out by three three-point bending tests and ultrasonic testing . Samples were conditioned at 20±1 °C and 45, 65, and 85% relative humidity. The calculated ultrasonic longitudinal wave velocity (VLL) was used to determine dynamic MOE (4549 to 4735 MPa) and compared to static MOE (5461 to 5910 MPa). Static MOE values are around 15.3% to 28.1% higher than dynamic values. MOR values, the most influenced properties, decreased from 70.1 MPa to 51.3 MPa with the increase in moisture. Pearson correlation coefficients ranged from 0.52 (MOR vs VLL) to 0.94 MOEdyn vs VLL). The R² values ranged from 0.187 (VLL vs MOR at 85% RH) to 0.94% (VLL vs Edyn at 65% RH).

Özet

Rutubetin, Populus x canadensis M.'in fiziksel (yoğunluk) ve mekanik (Eğilme direnci-MOR, Elastikiyet modülü-MOE) özellikleri üzerindeki etkisi üç nokta eğme testi ve ultrasonik test yöntemi ile belirlenmiştir. Örnekler 20±1 °C'de ve %45, 65 ve 85 bağıl nemde şartlandırılmıştır. Hesaplanan ultrasonik boyuna dalga hızı (VLL) dinamik MOE'yi (4549 ila 4735 MPa) belirlemek için kullanılmış ve statik MOE (5461 ila 5910 MPa) ile karşılaştırılmıştır. Statik MOE değerleri dinamik değerlerden yaklaşık %15.3 ila %28.1 daha yüksektir. Rutubetten en çok etkilenen özellik olan MOR değerleri, rutubetteki artışla birlikte 70.1 MPa'dan 51.3 MPa'ya düşmüştür. Pearson korelasyon katsayıları 0.52 (MOR vs VLL) ile 0.94 MOEdyn vs VLL) arasında değişmektedir. R² değerleri 0.187 (%85 bağıl nemde VLL vs MOR) ile %0.94 (%65 bağıl nemde VLL vs Edyn) arasında değişmiştir.

🔖

Cite This Article

Aydın, T. Y., Özkan, U. (2024). Moisture dependent bending properties of poplar. Türkiye Ormancılık Dergisi, Cilt: 25 Sayı: 4, 514–519. https://doi.org/10.18182/tjf.1547421

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (26)

  1. Aydın, M., Aydın, T.Y., 2023. Influence of growth ring number and width on elastic constants of poplar. Bioresources, 18(4): 8484–8502. https://doi.org/10.15376/biores.18.4.8484-8502
  2. Baar, J., Tippner, J., Rademacher, P., 2015. Prediction of mechanical properties - modulus of rupture and modulus of elasticity - of five tropical species by nondestructive methods. Maderas. Ciencia y tecnología, 17(2): 239-252. https://doi.org/10.4067/ S0718-221X2015005000023
  3. Bachtiar, E. V., Sanabria, S.J., Mittig, J.P., Niemz, P., 2017. Moisture-dependent elastic characteristics of walnut and cherry wood by means of mechanical and ultrasonic test incorporating three different ultrasound data evaluation techniques. Wood Science and Technology, 51: 47–67. https://doi.org/10.1007/ s00226-016-0851-z
  4. Balatinecz, J.J., Kretschmann, D.E., 2002. Properties and utilization of poplar wood. In: Poplar Culture in North America (Eds: Dickmann, D.I., Isebrands, J.G., Eckenwalder, J.E., Richardson, J.),. NRC Research Press, Dickmann, Donald I., pp. 277–291.
  5. Casado, M., Acuña, L., Vecilla, D., Relea, E., Basterra, A., Ramón, G., López, G., 2010. The influence of size in predicting the elastic modulus of Populus x euramericana timber using vibration techniques, In: Structures & Architecture (Ed: Cruz), CRC Press, London, pp. 579–579. https://doi.org/10.1201/ b10428-282
  6. Davis, P.H., 1982. Flora of Turkey and East Aegean Islands, Volume 7, Edinburg Universty Press, Edinburg, 947 p.
  7. Ettelaei, A., Layeghi, M., Zarea Hosseinabadi, H., Ebrahimi, G., 2019. Prediction of modulus of elasticity of poplar wood using ultrasonic technique by applying empirical correction factors. Measurement, 135: 392–399. https://doi.org/10.1016/j. measurement.2018.11.076
  8. Gallego, A., Ripoll, M.A., Timbolmas, C., Rescalvo, F., Suarez, E., Valverde, I., Rodríguez, M., Navarro, F.B., Merlo, E., 2021. Modulus of elasticity of I-214 young poplar wood from standing trees to sawn timber: Influence of the age and stand density. European Journal of Wood and Wood Products, 79: 1225–1239. https://doi.org/10.1007/s00107-021-01675-5
  9. Gerhards, C.C., 1982. Effect of moisture content and temperature on the mechanical properties of wood: An analysis of immediate effects. Wood and Fiber Science, 14(1): 4–36. Gray, J.D., Grushecky, S.T., Armstrong, J.P., 2008. Stress wave velocity and dynamic modulus of elasticity of yellow-poplar ranging from 100 to 10 percent moisture content. Proceedings of the 16th Central Hardwoods Forest Conference, 8-9 April, West Lafayette, USA, pp. 139–142.
  10. Hodoušek, M., Dias, A.M.P.G., Martins, C., Marques, A.F.S., Böhm, M., 2017. Comparison of non-destructive methods based on natural frequency for determining the modulus of elasticity of Cupressus lusitanica and Populus x canadensis. Bioresources, 12(1): 270–282.
  11. Koman, S., Feher, S., Abraham, J., Taschner, R., 2013. Effect of knots on the bending strength and the modulus of elasticity of wood. Wood Research, 58(4): 617–626.
  12. Kurt, R., 2010. Suitability of three hybrid poplar clones for laminated veneer lumber manufacturing using melamine urea formaldehyde adhesive. Bioresources, 5(3): 1868–1878.
  13. Longo, R., Laux, D., Pagano, S., Delaunay, T., Le Clézio, E., Arnould, O., 2018. Elastic characterization of wood by Resonant Ultrasound Spectroscopy (RUS): A comprehensive study. Wood Science and Technology, 52: 383–402. https://doi.org/10.1007/ s00226-017-0980-z
  14. Meija, A., Irbe, I., Morozovs, A., Spulle, U., 2020. Properties of Populus genus veneers thermally modified by two modification methods: wood treatment technology and vacuum thermal treatment. Agronomy Research, 18(3): 2138–2147. https://doi.org/ 10.15159/AR.20.184
  15. Papandrea, S.F., Cataldo, M.F., Bernardi, B., Zimbalatti, G., Proto, A.R., 2022. The predictive accuracy of modulus of elasticity (MOE) in the wood of standing trees and logs. Forests, 13(8): 1273. https://doi.org/10.3390/f13081273
  16. Pierre, F., Almeida, G., Huber, F., Jacquin, P., Perré, P., 2013. An original impact device for biomass characterisation: results obtained for spruce and poplar at different moisture contents. Wood Science and Technology, 47: 537–555. https:// doi.org/10.1007/s00226-012-0512-9
  17. TS 2472, 2005. Wood - Determination of density for physical and mechanical tests, Wood, sawlogs and sawn timber (ICS 79.040). Turkish Standard Institution, Ankara.
  18. TS ISO 13061-2, 2021. Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 2: Determination of density for physical and mechanical tests. Turkish Standard Institution, Ankara.
  19. TS ISO 13061-3, 2021. Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 3: Determination of ultimate strength in static bending. Turkish Standard Institution, Ankara.
  20. Varivodina, I., Mashkina, O., Varivodin, V., 2018. Technical characteristics of poplar wood as raw material for wide use in timber industry. ProLigno, 14: 20–27.
  21. Villasante, A., Vignote, S., Fernandez-Serrano, A., Laina, R., 2021. Simultaneous treatment with oil heat and densification on physical properties of Populus × Canadensis wood. Maderas. Ciencia y tecnología, 24(5): 1-12. https://doi.org/10.4067/ S0718-221X2022000100405
  22. Yılmaz Aydın, T., Aydın, M., 2018. Effect of density and propagation length on ultrasonic longitudinal wave velocity in some important wood species grown in Turkey. Turkish Journal of Forestry, 19(4): 413–418. https://doi.org/10.18182/tjf.459005
  23. Yılmaz Aydın, T., Aydın, M., 2020. Influence of temperature and exposure duration on the bending properties of oak wood. Journal of Bartin Faculty of Forestry, 22(3): 871–877. https://doi.org/10.24011/barofd.792268
  24. Yılmaz Aydın, T., 2021. Evaluation of heating temperature and time on bending properties of Taurus cedar wood. Turkish Journal of Forestry, 22(4): 432–438. https://doi.org/10.18182/tjf.1019032
  25. YingJie, Z., DeJun, F., YanGuang, D., 2017. Wood physical and mechanical properties of Populus × canadensis Moench and Populus × euramericana (Dode) Guinier cv. Gelrica. Agricultural Science and Technology, 18(12): 2532–2535.
  26. Zahedi, M., Kazemi Najafi, S., Füssl, J., Elyasi, M., 2022. Determining elastic constants of poplar wood (Populus deltoides) by ultrasonic waves and its application in the finite element analysis. Wood Material Science and Engineering, 17(6): 668–678. https://doi.org/10.1080/17480272.2021.1925962