Dergiler / Konya Journal of Engineering Sciences / 2017 / Cilt: 5 Sayı: 2

PMN-PT-PMS SERAMİKLERİNDE SİNTERLEME SICAKLIĞI ETKİSİYLE YAPISAL VE ELEKTRİKSEL ÖZELLİKLERİN OPTİMİZASYONU

Optimizing Structural and Electrical Properties of PMN-PT-PMS Ceramics via Sintering Temperature

Sayfa
144–152
Yayın Tarihi
2017-06-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

PMS [Pb(Mn1/3Sb2/3)O3] ile katkılanmış PMN-PT [Pb(Mg1/3Nb2/3)O3-PbTiO3] üçlü piezoelektrik

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:PMS [Pb(Mn1/3Sb2/3)O3] ile katkılanmış PMN-PT [Pb(Mg1/3Nb2/3)O3-PbTiO3] üçlü piezoelektrik
📊
Temel Bulgular & Veri:PMS [Pb(Mn1/3Sb2/3)O3] ile katkılanmış PMN-PT [Pb(Mg1/3Nb2/3)O3-PbTiO3] üçlü piezoelektrik
💡
Sonuç & Katkı:PMS [Pb(Mn1/3Sb2/3)O3] ile katkılanmış PMN-PT [Pb(Mg1/3Nb2/3)O3-PbTiO3] üçlü piezoelektrik
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Piezoelektrik özellikler · Sinterleme · PMN-PT

Özet

PMS [Pb(Mn1/3Sb2/3)O3] ile katkılanmış PMN-PT [Pb(Mg1/3Nb2/3)O3-PbTiO3] üçlü piezoelektrik

Abstract

Pseudo-ternary piezoelectric ceramics of PMN-PT [Pb(Mg1/3Nb2/3)O3-PbTiO3] compositionmodified with PMS [Pb(Mn1/3Sb2/3)O3] were produced by solid-state sintering method using differenttemperatures in a range of 1100-1250 °C. The effect of sintering temperature on the crystal phases,microstructure and electrical properties were systematically investigated. Microstructural andcompositional analyses have been carried out using scanning electron microscope (SEM) and X-raydiffraction (XRD). Besides, electrical characterization was performed using an inductance-capacitanceresistance(LCR) meter, impedance analyzer and a Berlincourt d33-piezometer. XRD and SEM resultsindicated that the sintering temperature was effective on the formation of a homogeneousmicrostructure and a pure perovskite structure. Densification during sintering could not be completedand pure perovskite structure was not o tained at 1150 °C and lower sintering temperatures.Furthermore, sintering at temperatures higher than 1200 °C resulted in heterogeneous microstructure.The high dielectric and piezoelectric response of PMN-PT-PMS ceramics is considered to be a result oftheir high densities and homogeneous microstructure obtained via proper sintering condition. Theresults showed that the ceramic samples sintered at 1175 °C for 2 h possessed the optimum properties(d33=265 pC/N, KT=4745, kp=0.417, tanδ=2.5%, Qm=222).

🔖

Bu Makaleye Atıf Yap

DÜZEN, O., KALEM, V. (2017). PMN-PT-PMS SERAMİKLERİNDE SİNTERLEME SICAKLIĞI ETKİSİYLE YAPISAL VE ELEKTRİKSEL ÖZELLİKLERİN OPTİMİZASYONU. Konya Journal of Engineering Sciences, Cilt: 5 Sayı: 2, 144–152. https://ajindex.com/articles/906151

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

  1. Aydın H.S., 2016, PMN-PT[Pb(Mg1/3Nb2/3)O3-PbTiO3] Esaslı Piezoelektrik Seramiklerin Üretimi ve Karakterizasyonu, Yüksek Lisans Tezi, Selçuk Üniversitesi,
  2. Fen Bilimleri Enstitüsü, Konya. Aydın H.S., Kalem V., 2016, ‚PMN-PT [Pb(Mg1/3Nb2/3)O3-PbTiO3] Esaslı Seramiklerde Kompozisyonun Yapısal ve Elektriksel Özelliklere Etkisi‛, Selçuk Üniversitesi Mühendislik Bilim ve Teknoloji Dergisi, Vol. 4, No. 2, pp. 100-110.
  3. Bouquin, O., Lejeune, M., Boilot, J.P., 1991, ‚Formation of The Perovskite Phase in the PbMg1/3Nb2/3O3- PbTiO3 system‛, Journal of the American Ceramic Society, Vol.74, No. 5, pp. 1152-56.
  4. Carter, C.B., Norton, M.G., 2007, Ceramic Materials: Science and Engineering, Springer, New York. Choi, S.W., Shrout, T.R., Jang, S.J., Bhalla, A.S., 1989, ‚Dielectric and Pyroelectric Properties in The Pb(Mg1/3Nb2/3)O3-PbTiO3 system‛, Ferroelectrics, Vol. 100, pp. 29-38.
  5. Guha, J.P., 1999, ‚Reaction Chemistry and Subsolidus Phase Equilibria in Lead-based Relaxor Systems: Part I - Formation and Stability of The Perovskite and Pyrochlore Compounds in The System PbO-MgO-Nb2O5‛, Journal of Materials Science, Vol. 34, No. 20, pp. 4985-94.
  6. Hai, L., Bo-Ping, Z., Yu, P., Lei, Z., Kai-sheng, W., Yan-tao, L., 2015, ‚Effects of Sintering Temperature on Structure and Properties of BY-PT-PMN Ternary Piezoelectric Ceramics‛, Journal of Materials Research, Vol. 30, No. 6, pp. 782-790.
  7. Hoffmann, M.J., Hammer M., Endriss A., Lupascu D.C., 2001, ‚Correlation Between Microstructure, Strain Behavior, and Acoustic Emission of Soft PZT Ceramics‛, Acta Materialia, Vol.49, pp. 1301–1310.
  8. Inada, M., 1977, ‚Analysis of The Formation Process of the Piezoelectric PCM Ceramics‛, National Technical Report (Matsushita Elect. Ind. Co.), Vol. 27, No. 1, pp. 95-102.
  9. Ketsuwan, P., Ngamjarurojana, A., Laosiritaworn, Y., Ananta, S., Yimnirun, R., 2007, ‚Effect of Sintering Temperature on Phase Formation, Dielectric, Piezoelectric, and Ferroelectric Properties of Nb- Doped Pb(Zr0.52Ti0.48)O3 Ceramics‛, Ferroelectrics, Vol. 358, pp. 35-41.
  10. Liu, L., Fan, H., Ke, S., Chen, X., 2008, ‚Effect of Sintering Temperature on The Structure and Properties of Cerium-Doped 0.94(Bi0.5Na0.5)TiO3–0.06BaTiO3 Piezoelectric Ceramics‛, Journal of Alloys and Compounds, Vol. 458, pp. 504-508.
  11. Naceur, H., Megriche, A., El Maaoui, M., 2014, ‚Effect of Sintering Temperature on Microstructure and Electrical Properties of Sr1-x(Na0.5Bi0.5)xBi2Nb2O9 Solid Solutions‛, Journal of Advanced Ceramics, Vol. 3, No. 1, pp. 17-30. Shrout,