Dergiler / Current Research in Dental Sciences / 2021 / Cilt: 31 Sayı: 2

FARKLI ZİRKONYA ALTYAPILI KURONLARIN MARJİNAL UYUM VE KIRILMA DİRENÇLERİNİN DEĞERLENDİRİLMESİ

Sayfa
247–255
Yayın Tarihi
2021-04-15
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Bulgular: Everest grubuna ait örnekler marjinal uyum açısından hem simantasyon öncesi (24,80 ± 4,77 µ) hem de simantasyon sonrası (41,86 ± 5,41 µ) en düşük değerleri verdi (p<0.001).

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Amaç: Bu çalışmanın amacı 5 farklı yöntemle hazırlanan zirkonya altyapılı porselen kuronların marjinal uyum ve kırılma dirençlerini in vitro olarak değerlendirmektir.
📊
Temel Bulgular & Veri:Gereç ve yöntem: Prepare edilmiş molar dişi temsilen 30 adet paslanmaz çelik güdük her grupta 6 adet olacak şekilde 5 gruba ayrıldı.. 1. grup slip-casting yöntemi ile hazırlanan In-Ceram Zirconia, 2. grup electrodepositing yöntemi ile hazırlanan Wol-Ceram, 3. grup manuel dizayn ve manuel kopya üretim ile hazırlanan ZirkonZahn, 4. grup manuel dizayn ve dijital üretim ile hazırlanan Cercon ve 5. grup dijital dizayn ve dijital üretim ile hazırlanan Everest örneklerden oluşturuldu.
💡
Sonuç & Katkı:Bulgular: Everest grubuna ait örnekler marjinal uyum açısından hem simantasyon öncesi (24,80 ± 4,77 µ) hem de simantasyon sonrası (41,86 ± 5,41 µ) en düşük değerleri verdi (p<0.001).
🔬Tür:Araştırma Makalesi
📍Kapsam:30 adet
⚙️Değişkenler:Zirkonya · marjinal uyum · kırılma direnc

Özet

Amaç: Bu çalışmanın amacı 5 farklı yöntemle hazırlanan zirkonya altyapılı porselen kuronların marjinal uyum ve kırılma dirençlerini in vitro olarak değerlendirmektir. Gereç ve yöntem: Prepare edilmiş molar dişi temsilen 30 adet paslanmaz çelik güdük her grupta 6 adet olacak şekilde 5 gruba ayrıldı.. 1. grup slip-casting yöntemi ile hazırlanan In-Ceram Zirconia, 2. grup electrodepositing yöntemi ile hazırlanan Wol-Ceram, 3. grup manuel dizayn ve manuel kopya üretim ile hazırlanan ZirkonZahn, 4. grup manuel dizayn ve dijital üretim ile hazırlanan Cercon ve 5. grup dijital dizayn ve dijital üretim ile hazırlanan Everest örneklerden oluşturuldu. Kuronlar simante edilmeden önce ve sonra optik mikroskop ile marjinal uyum açısından değerlendirildi. Verilerin değerlendirilmesinde Student t testi uygulandı. Simantasyon sonrası termal siklus uygulanan kuronların kırılma dirençleri, 0.5 mm/dakika başlık hızına ayarlı universal test cihazında ölçüldü. Veriler tek yönlü varyans analizi (ANOVA) ile değerlendirildi. Bulgular: Everest grubuna ait örnekler marjinal uyum açısından hem simantasyon öncesi (24,80 ± 4,77 µ) hem de simantasyon sonrası (41,86 ± 5,41 µ) en düşük değerleri verdi (p<0.001). Bunu, her iki ölçümde, sırası ile Cercon, Wol-Ceram, ZirkonZahn ve In-ceram Zirconia gruplarına ait örnekler takip etti. En yüksek kırılma direnci değerini Everest grubuna ait örnekler gösterdi (1653,33 ± 53,54 N) (p<0.01). Bunu Cercon, ZirkonZahn, Wol-Ceram ve In-Ceram Zirconia grubuna ait örnekler takip etti. Sonuçlar: Zirkonya altyapılı kuronların kırılma direnci ve marginal adaptasyonu üzerinde farklı hazırlama yöntemlerinin etkisi önemlidir. Dijital hazırlama yöntemi marginal uyum ve kırılma direnci açısından daha iyi sonuç vermiştir. İstatistiksel farklılıklara rağmen çalışmada kullanılan materyaller klinik olarak kabul edilir değerler sağlamıştır. Anahtar kelimeler: Zirkonya, marjinal uyum, kırılma direnci EVALUATION OF MARGINAL ADAPTATION AND FRACTURE STRENGTH OF DIFFERENT ZIRCONIA BASED CROWNS ABSTRACT Aim: The purpose of this study was in-vitro evaluation of marginal adaptation and fracture strength of zirconia based ceramic crowns prepared in five different ways. Material and Methods: 30 stainless steel dies representing a molar crown were formed. 5 groups containig 6 dies each were formed. Groups were as follows: group 1. In-Ceram Zirconia prepared by slipcasting, group 2. Wol-Ceram prepared by electro-depositing, group 3. ZirkonZahn prepared by manual design and manufacturing, group 4. Cercon prepared by manuel design and digital manufacturing, group5. Everest prepared by digital design and digital manufacturing. All the crowns were evaluated for marginal adaptation before and after cementation by using stereo microscope. Data were statistically evaluated by Student t test. Fracture strengths of crowns were measured by a universal testing machine at a cross-head speed of 5mm/minute after thermo-cycling. One way ANOVA test were used to evaluate the data. Results: Everest group showed the lowest marginal adaptation values before (24,80 ± 4,77 µ) and after cementation (41,86 ± 5,41 µ) (p<0.001). This was followed by Cercon, Wol-Ceram, Zirkonzahn, In-Ceram Zirconia groups in both measurements. The highest fracture strength value was obtained from Everest group (1653,33 ± 53,54 N) (p<0.01). This was followed by Cercon, ZirkonZahn, Wol-Ceram and In-Ceram Zirconia groups. Conclusion: Different preparation methods have important effect on marginal adaptation and fracture strength of zirconia based crowns. Digital manufacturing technique showed better marginal adaptation and fracture strength results. Despite the statistical differences all of the materials used in this study showed clinically accepted values. Key words: Zirconia, marginal adaptation, fracture strength

🔖

Bu Makaleye Atıf Yap

YILMAZ, B., YANIKOĞLU, N. (2021). FARKLI ZİRKONYA ALTYAPILI KURONLARIN MARJİNAL UYUM VE KIRILMA DİRENÇLERİNİN DEĞERLENDİRİLMESİ. Current Research in Dental Sciences, Cilt: 31 Sayı: 2, 247–255. https://ajindex.com/articles/900928

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (15)

  1. Samorodnitzky-Naveh GR, Geiger SB, Levin L. Patients’ satisfaction with dental esthetics. Journal of the American Dental Association 2007;138:805-808
  2. Zhang Y, Kelly JR. Dental ceramics for restoration and metal veneering. Dent Clin North Am 2017; 61: 797–819
  3. Touati B, Miara P, Nathanson D. Esthetic Dentistry And Ceramic Restorations. London, Martin Dunitz Ltd., 1999: 25-26
  4. Vagkopoulou T, Koutayas SO, Koidis P, Strub JR. Zirconia in dentistry: Part 1. Discovering the nature of an upcoming bioceramic. Eur J Esthet Dent. 2009; 4:130-151
  5. Raigrodski AJ, Hillstead MB, Meng GK, Chung KH. Survival and complications of zirconia-based fixed dental prostheses: a systematic review. J Prosthet Dent. 2012; 107:170-177
  6. Rimondini L, Cerroni L, Carrassi A, Torricelli P. Bacterial colonization of zirconia ceramic surfaces: an in vitro and in vivo study. Int J Oral Maxillofac Implants. 2002; 17: 793- 798
  7. Özyer EK, Kahramanoğlu E, Akmansoy CŞ, Özkan YK. Zirkonyum Destekli Sabit Protetik Restorasyonlarda Klinik Başarı Değerlendirme Kriterleri. European Journal of Research in Dentistry 2019; 3: 53–62
  8. Yüksel G, Çekiç C, Özkan P. Metal desteksiz porselen sistemleri. Atatürk Üniv Diş Hek Fak Derg. 2000; 10(2): 79- 89
  9. Hummert T, Barghi N, Berry T. Postcementation Marginal fit of a new ceramic foil crown system. J Prosthet Dent. 1992; 68(5): 766-770
  10. Holmes JR, Sulik WD, Holland GA, Bayne SC. Marginal fit of castable ceramic crowns. J Prosthet Dent. 1992; 67(5): 594-599
  11. Sulaiman F, Chai J, Jameson LM, Wozniak WT. A comparison of the marginal fit of ın-ceram, IPS empress and procera crowns. Int J Prosthodont. 1997; 10(5): 478-484
  12. Schmitter M, Mueller D, Rues S. In vitro chipping behavior of all-ceramic crowns with a zirconia framework and feldspathic veneering: comparison of CAD/CAM-produced veneer with manually layered veneer. Journal of Oral Rehabilitation 2013; 40:519-525
  13. Lopez-Suarez C, Tobar C, Sola-Ruiz MF, Pelaez J, Suarez MJ. Effect of thermomechanical and static loading on the load to fracture of metal-ceramic, monolithic, and veneered zirconia posterior fixed partial dentures. Journal of Prosthodontics 2019; 28(2):171-178
  14. Güngör MB, Nemli SK. Fracture resistance of CAD-CAM monolithic ceramic and veneered zirconia molar crowns after aging in a mastication simulator. Journal of Prosthetic Dentistry 2018;119(3):473-480
  15. Kheradmandan S, Koutayas SO, Bernhard M, Strub JR. Fracture strength of four different types of