Dergiler / Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji / 2023 / Cilt: 11 - Sayı: 1

Vakum İnfüzyon Yöntemi ile Üretilen Parçalarda Jelkot Kullanımı ve Elyaf Laminasyonunun Mekanik Özelliklere Etkisi

The Effect of Gelcoat Usage and Fiber Lamination on Mechanical Properties in Parts Produced by Vacuum Infusion Method

Sayfa
197–209
Yayın Tarihi
2023-03-25
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Test sonuçlarına göre yapıda bez ayağı dokuma oranı artmasıyla birlikte eğme mukavemetinde %11,2-18,7 arasında; çekme mukavemetinde ise %11,7-16,6 arasında artış gözlemlenmiştir.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışmada vakum infüzyon yöntemi ile üretilen kompozit yapılarda yüzey katmanında kullanılan jelkotun mekanik özelliklere etkisi ve laminasyon planının nihai ürün üzerindeki etkileri araştırılmıştır.
📊
Temel Bulgular & Veri:İki farklı laminasyon planı belirlenmiş ve bu iki farklı laminasyonun jelkotlu ve jelkotsuz plakaları üretilmiştir.
💡
Sonuç & Katkı:Test sonuçlarına göre yapıda bez ayağı dokuma oranı artmasıyla birlikte eğme mukavemetinde %11,2-18,7 arasında; çekme mukavemetinde ise %11,7-16,6 arasında artış gözlemlenmiştir.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Jelkot · Laminasyon · Kompozit Malzemeler

Özet

Bu çalışmada vakum infüzyon yöntemi ile üretilen kompozit yapılarda yüzey katmanında kullanılan jelkotun mekanik özelliklere etkisi ve laminasyon planının nihai ürün üzerindeki etkileri araştırılmıştır. İki farklı laminasyon planı belirlenmiş ve bu iki farklı laminasyonun jelkotlu ve jelkotsuz plakaları üretilmiştir. Laminasyonlarda 300 gr/m2 keçe ve 300 gr/m2 bezayağı dokuma cam elyaf takviyeler kullanılmıştır. Çalışma kapsamında mekanik özellikleri araştırmak için çekme, üç nokta eğme ve barcol sertlik testleri yapılmıştır. Test sonuçlarına göre yapıda bez ayağı dokuma oranı artmasıyla birlikte eğme mukavemetinde %11,2-18,7 arasında; çekme mukavemetinde ise %11,7-16,6 arasında artış gözlemlenmiştir. Jelkot kullanımının mekanik özelliklere etkisinin büyük olduğu tespit edilmiştir. Jelkot kullanımı ile birlikte eğme mukavemetinde %24,3’e kadar düşüş gözlemlenirken; çekme mukavemetinde %17,8’e kadar düşüş gözlemlenmiştir. Bezayağı dokuma cam elyaf katmanının yüzeye daha yakın olduğu laminasyonlarda %5’e kadar daha yüksek barcol sertlik değerleri elde edilmiştir.

Abstract

In this study, the effect of the gelcoat on the surface layer of the composite structures produced by vacuum infusion method on the mechanical properties and the effects of the lamination plan on the final product were investigated. Two different lamination plans were determined and gelcoat and non-gelcoat plates of these two different laminations were produced. In laminations, 300 gr/m2 discontinious mat and 300 gr/m² plain woven glass fiber reinforcements were used. Within the scope of the study, tensile, three-point bending and barcol hardness tests were carried out to investigate the mechanical properties. According to the test results, with the increase in the plain woven ratio in the structure, the bending strength is between 11.2-18.7%; an increase of 11.7-16.6% was observed in the tensile strength. It has been determined that the use of gelcoat has a great effect on the mechanical properties. With the use of gelcoat, a decrease of up to 24.3% was observed in the flexural strength; A decrease of up to 17.8% was observed in tensile strength. Up to 5% higher barcol hardness values were obtained in laminations where the plain woven glass fiber layer is closer to the surface.

🔖

Bu Makaleye Atıf Yap

KELEŞ, M., YILDIRIM, K., TOPBAŞOĞLU, M. C. (2023). Vakum İnfüzyon Yöntemi ile Üretilen Parçalarda Jelkot Kullanımı ve Elyaf Laminasyonunun Mekanik Özelliklere Etkisi. Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji, Cilt: 11 - Sayı: 1, 197–209. https://ajindex.com/articles/886045

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (15)

  1. Tong, L., Mouritz, A., & Bannister, M.K. (2002). 3D Fibre Reinforced Polymer Composites
  2. Bakis, C.E., Bank, L.C., Brown, V.L., Cosenza, E., Davalos, J.F., Lesko, J.J., Machida, A., Rizkalla, S.H., & Triantafillou, T.C. (2002). Fiber-Reinforced Polymer Composites for Construction—State-of-the-Art Review. Journal of Composites for Construction, 6, 73-87
  3. Saheb, D. N., & Jog, J. P. 1999. Natural fiber polymer composites: a review. Advances in Polymer Technology: Journal of the Polymer Processing Institute, 18(4), 351-363 [4] Zheng, Y., Wang, W., Mosalam, K.M., & Zhong-feng, Z. (2018). Mechanical behavior of ultra-high toughness cementitious composite strengthened with Fiber Reinforced Polymer grid. Composite Structures, 184, 1-10
  4. Wilson, A. (2017). Vehicle weight is the key driver for automotive composites. Reinforced Plastics, 61, 100-102
  5. Markets and Market, (2021), Composites Market by Fiber Type, Resin Type, Manufacturing Process, End-Use Industry and Region – Global Forecast to 2026,
  6. Sezgin, H., & Berkalp, O.B. (2017). The effect of hybridization on significant characteristics of jute/glass and jute/carbon-reinforced composites. Journal of Industrial Textiles, 47, 283 - 296
  7. Campbell, F.C. (2010). Structural Composite Materials
  8. Lee, D.G. (2005). Axiomatic Design and Fabrication of Composite Structures: Applications in Robots, Machine Tools, and Automobiles
  9. Shahzad, A. (2014). Impact and Fatigue Properties of Natural Fibre Composites
  10. Wallenberger, F.T., Macchesney, J.B., Naslain, R.R., & Ackler, H.D. (1999). Advanced inorganic fibers: Processes, structures, properties and applications
  11. Lee, H., Jung, K.H., & Park, H. (2021). Study on Structural Design and Analysis of Composite Boat Hull Manufactured by Resin Infusion Simulation. Materials, 14
  12. Sakin, R. (2021). Layup Design Optimization for E-glass Woven Roving Fabric Reinforced Polyester Composite Laminates Produced by VARTM. Fibers and Polymers, 22, 509-527
  13. Demircan, G., Ozen, M., & Kısa, M. (2020). Flexural Properties of Glass Fiber Reinforced Epoxy Composites at Different Strain Rates
  14. Ertan, R., Kuş, A., & Durgun, I. (2019). ÜÇ BOYUTLU DOKUMA KUMAŞ TAKVİYELİ SANDVİÇ KOMPOZİTLERDE YÜZEYLERDEKİ ELYAF KATMAN SAYISININ EĞİLME DAVRANIŞINA ETKİSİ. Uludağ University Journal of The Faculty of Engineering, 24, 231-240
  15. Çakir, M.C., & Berberoğlu, B. (2018). E-Cam Elyaf Takviyel