Dergiler / Politeknik Dergisi / 2022 / Cilt: 25 - Sayı: 4

LDPE ve C/LDPE Ambalaj Atıklarının Pirolizi ve Farklı Parametrelerin Sıvı Ürüne Etkisi

Effects of Different Parameters on Pyrolytic Liquid Product of Waste LDPE and C/LDPE Packages

Sayfa
1575–1585
Yayın Tarihi
2022-12-16
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Sonuçlara göre, atık C/LDPE’den elde edilen ürün ticari ‘heavy wax’ ile benzerlik göstermektedir.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışma; poliolefin plastik sınıfında en fazla atık hacmine sahip olan düşük yoğunluklu polietilen (LDPE) ve ambalajlamada sıkça kullanılan alüminyum içerikli kompozitlerinin (C/LDPE), katma değerli ürünler elde etmek için pirolizi ve elde edilen ürünlerin karakterizasyonunu içermektedir.
📊
Temel Bulgular & Veri:LDPE ve C/LDPE atıkları, kısa analiz, elementel analiz ve TGA ile incelenmiş; ardından farklı sıcaklık (400-600-800 ℃) ve ısıtma hızlarında (5-10-20 ℃/dk) sabit yataklı reaktörde piroliz edilmiştir.
💡
Sonuç & Katkı:Sonuçlara göre, atık C/LDPE’den elde edilen ürün ticari ‘heavy wax’ ile benzerlik göstermektedir.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:LDPE · C/LDPE · katalizör

Özet

Bu çalışma; poliolefin plastik sınıfında en fazla atık hacmine sahip olan düşük yoğunluklu polietilen (LDPE) ve ambalajlamada sıkça kullanılan alüminyum içerikli kompozitlerinin (C/LDPE), katma değerli ürünler elde etmek için pirolizi ve elde edilen ürünlerin karakterizasyonunu içermektedir. LDPE ve C/LDPE atıkları, kısa analiz, elementel analiz ve TGA ile incelenmiş; ardından farklı sıcaklık (400-600-800 ℃) ve ısıtma hızlarında (5-10-20 ℃/dk) sabit yataklı reaktörde piroliz edilmiştir. Sonrasında atıklar, zeolit katalizörlüğünde 600 °C sıcaklık ve 20 °C/dk ısıtma hızında piroliz edilerek, katalizörün sıvı ürün üzerindeki etkisi değerlendirilmiştir. Elde edilen sıvı ürünün vaks olarak değerlendirilme potansiyelini belirlemek için, sıvı ürünlerin ve temin edilen ticari vaksların GC-MS, FT-IR ve 1H-NMR analizleri yapılmıştır. Sonuçlara göre, atık C/LDPE’den elde edilen ürün ticari ‘heavy wax’ ile benzerlik göstermektedir.

Abstract

This study is about the thermal pyrolysis of low-density polyethylene (LDPE), which has the highest waste volume in the polyolefins plastic class, and aluminum-containing composites (C/LDPE), which are frequently used in packaging, to recover value-added products and then characterize the products obtained. LDPE and C/LDPE wastes were examined by proximate analysis, elemental analysis and TGA, and then pyrolyzed in a fixed bed reactor at different temperatures (400-600-800 ℃) and different heating rates (5-10-20 ℃/min). Afterwards, the wastes were pyrolyzed at 600 °C and 20 °C/min heating rate with zeolite catalysis and the effect of the catalyst on the liquid product was evaluated. GC-MS, FT-IR and 1H-NMR analyzes of the pyrolytic liquid products and commercial waxes were performed to determine the potential of the obtained liquid product to be used as a wax. According to the results, the product obtained from waste C/LDPE is similar to commercial heavy wax.

🔖

Bu Makaleye Atıf Yap

YAPICI, E., AKGÜN, H., ÖZKAN, A., GÜNKAYA, Z., BANAR, M. (2022). LDPE ve C/LDPE Ambalaj Atıklarının Pirolizi ve Farklı Parametrelerin Sıvı Ürüne Etkisi. Politeknik Dergisi, Cilt: 25 - Sayı: 4, 1575–1585. https://ajindex.com/articles/880112

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (14)

  1. Arabiourrutia, M., Elordi, G., Lopez, G., Borsella, E., Bilbao, J., & Olazar, M., ‘Characterization of the waxes obtained by the pyrolysis of polyolefin plastics in a conical spouted bed reactor’, J. Anal. Appl. Pyrolysis, 94: 230-237, (2012)
  2. Rodríguez, E., Palos, R., Gutiérrez, A., Trueba, D., Arandes, J. M., & Bilbao, J., ‘Towards waste refinery: Co-feeding HDPE pyrolysis waxes with VGO into the catalytic cracking unit’, Energy Convers. Manage., 207, 112554, (2020)
  3. Mukherjee, A., Ruj, B., Gupta, P., & Sadhukhan, A. K., ‘A study on pyrolysis of plastic wastes for product recovery and analysis’ Urban Mining and Sustainable Waste Management, Springer, Singapore, (2020)
  4. PAGEV, Türkiye Plastik Sektör İzleme Raporu 2020/3 (2020)
  5. Sogancioglu, M., Yel, E., & Ahmetli, G., ‘Pyrolysis of waste high density polyethylene (HDPE) and low density polyethylene (LDPE) plastics and production of epoxy composites with their pyrolysis chars’ J. Cleaner Prod., 165, 369-381, (2017)
  6. Muralisrinivasan Subramanian, N., ‘Plastics waste management: processing and disposal’ Shawbury, Shrewsbury, Shropshire, UK: Smithers Rapra, (2016)
  7. Park, J. J., Park, K., Park, J. W., & Kim, D. C., "Characteristics of LDPE pyrolysis", Korean J. Chem. Eng.,19(4), 658, (2002)
  8. Sharuddin S.D.A., Abnisa F., Daud W., Aroua M.K., ‘A Review On Pyrolysis Of Plastic Wastes’, Energy Convers. Manage., 115, 308–326, (2016)
  9. Oliveux, G., Dandy, L. O., & Leeke, G. A., ‘Current status of recycling of fibre reinforced polymers: Review of technologies, reuse and resulting properties’ Prog. Mater Sci., 72, 61-99, (2015)
  10. Dewangan, A., Pradhan, D., & Singh, R. K., ‘Co-pyrolysis of sugarcane bagasse and low-density polyethylene: influence of plastic on pyrolysis product yield’ Fuel, 185, 508-516, (2016)
  11. Zattini, G., Leonardi, C., Mazzocchetti, L., Cavazzoni, M., Montanari, I., Tosi, C.,. & Giorgini, L., ‘Pyrolysis of Low-Density Polyethylene’ In International Conference on Sustainable Design and Manufacturing (pp. 480-490). Springer, Cham. (2017)
  12. Papuga, S. V., Gvero, P. M., & Vukić, L. M., ‘Temperature and time influence on the waste plastics pyrolysis in the fixed bed reactor’ Thermal science, 20(2), 731-741, (2016)
  13. Sharuddin S.D.A., Abnisa F., Daud W., Aroua M.K., ‘A Review On Pyrolysis Of Plastic Wastes’, Energy Convers. Manage., 115, 308–326, (2016)
  14. Gao, F., ‘Pyrolysis of Waste Plastics into Fuels’, Yayımlanmamış Doktora Tezi. Canterbury: Un