Dergiler / Afyon Kocatepe Üniversitesi Fen ve Mühendislik Bilimleri Dergisi / 2022 / Cilt: 22 - Sayı: 5

Kesme Parametrelerinin Haynes 242 Nikel Bazlı Süper Alaşım Malzemenin Tornalamasında Güç Tüketimi Üzerindeki Etkilerinin RSM ve GA ile İncelenmesi

Investigation the Effects of Cutting Parameters on Power Consumption in Turning of Haynes 242 Nickel-Based Super Alloy by RSM and GA

Sayfa
1204–1213
Yayın Tarihi
2022-10-27
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Sonuç olarak, bu yöntemlerle bulunan tahmin değerleri karşılaştırılmış ve birbirlerine çok yakın oldukları görülmüştür.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Talaşlı imalatta yaygın kullanımı nedeniyle tornalama işleminde güç tüketimini azaltmak sürdürülebilir bir üretim süreci için kilit faktörlerden biridir.
📊
Temel Bulgular & Veri:Bu çalışmanın amacı işlem parametrelerinin Haynes 242 nikel bazlı süper alaşım malzemenin tornalanmasında güç tüketimi üzerine etkilerinin incelenmesidir.
💡
Sonuç & Katkı:Sonuç olarak, bu yöntemlerle bulunan tahmin değerleri karşılaştırılmış ve birbirlerine çok yakın oldukları görülmüştür.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Tornalama · Nikel Esaslı Süperalaşım · RSM

Özet

Talaşlı imalatta yaygın kullanımı nedeniyle tornalama işleminde güç tüketimini azaltmak sürdürülebilir bir üretim süreci için kilit faktörlerden biridir. Nikel bazlı süper alaşımlar, üstün mekanik özelliklerinden nedeniyle endüstride sıklıkla tercih edilirler. Bu çalışmanın amacı işlem parametrelerinin Haynes 242 nikel bazlı süper alaşım malzemenin tornalanmasında güç tüketimi üzerine etkilerinin incelenmesidir. Bu kapsamda, yanıt yüzeyi yöntemi (Response Surface Method-RSM) ile birleştirilen üç seviye Box-Behnken tasarımı ve genetik algoritma (GA) uygulanarak minimum güç tüketiminin tahmin edilmesinde kullanılan optimum parametre değerlerini belirlemek için regresyon modeli oluşturulmuştur. İlk olarak 3 farklı seviyedeki takım uç radüsü (0.4,0.6 ve 0.8 mm), talaş derinliği (0.2,0.4 ve 0.6 mm), ve ilerleme oranı (0.1,0.2 ve 0.3 mm/rev.) dikkate alınarak Box-Behnken deney tasarımı oluşturulmuştur. Ardından, elde edilen deney setlerine göre AdvantEdge™ vasıtasıyla her bir deney setine ait güç tüketimleri ölçülmüştür. Sonrasında, RSM’den elde edilen matematiksel tahmin modelinden yararlanılarak güç tüketimi tahmini için GA kullanılmıştır. Sonuç olarak, bu yöntemlerle bulunan tahmin değerleri karşılaştırılmış ve birbirlerine çok yakın oldukları görülmüştür. Hem istatistiksel hem de simülasyon programı sonuçları, güç tüketimini minimize etmek için düşük ilerleme oranı ve talaş derinliğine ihtiyaç duyulduğunu göstermektedir.

Abstract

Due to its widespread use in machining, reducing power consumption in the turning process is one of the key factors for a sustainable production process. Nickel-based superalloys are preferred in variable applications due to their superior mechanical properties. This study aims to investigate the effects of process parameters on power consumption in turning of Haynes 242 nickel-based superalloy. In this context, three levels of Box-Behnken design combined with the Response Surface Method (RSM) and genetic algorithm (GA) were applied to find the optimum parameter values used in the estimation of the minimum power consumption to create the regression model. First, the Box-Behnken experimental design was created based on 3 different levels of tool nose radius (0.4,0.6 and 0.8 mm), depth of cut (0.2,0.4 and 0.6 mm), and feed rate (0.1,0.2 and 0.3 mm/rev.). Then, the power consumption of each test measured by AdvantEdge™ based on the obtained experimental sets. Then, GA was used for power consumption estimation by utilizing the mathematical estimation model obtained from RSM. Finally, the estimated values obtained by both methods were compared. Both statistical and simulation results show that low feed rate and depth of cut are needed to minimize power consumption.

🔖

Bu Makaleye Atıf Yap

KAZAN, H., ERGÜL, E. U. (2022). Kesme Parametrelerinin Haynes 242 Nikel Bazlı Süper Alaşım Malzemenin Tornalamasında Güç Tüketimi Üzerindeki Etkilerinin RSM ve GA ile İncelenmesi. Afyon Kocatepe Üniversitesi Fen ve Mühendislik Bilimleri Dergisi, Cilt: 22 - Sayı: 5, 1204–1213. https://ajindex.com/articles/874237

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (10)

  1. Alvarez, M., Ilzarbe, L., Viles, E. and Tanco, M., 2009. The use of genetic algorithms in response surface methodology. Quality Technology & Quantitative Management, 6(3), 295-307.
  2. Aydın, K., Akgün, A., Yavaş, Ç., Gök, A. and Şeker, U., 2021. Experimental and Numerical Study of Cutting Force Performance of Wave Form End Mills on Gray Cast Iron. Arabian Journal for Science and Engineering, 46(12), 12299-12307.
  3. Aydin, K., Katmer, S., Gok, A. and Seker, U., 2021. Experimental and statistical investigation of the machining performance of wave form end mills on AISI 316L stainless steel. Journal of the Faculty of Engineering and Architecture of Gazi University, 36(4), 2225-2238.
  4. Chen, S.-H. and Tsai, K.-T., 2017. The study of plasma-assisted machining to Inconel-718. Advances in Mechanical Engineering, 9(12), 1687814017735789. Choudhury, I. and El-Baradie, M., 1998. Machinability of nickel-base super alloys: a general review. Journal of Materials Processing Technology, 77(1-3), 278-284.
  5. Duflou, J. R., Sutherland, J. W., Dornfeld, D., Herrmann, C., Jeswiet, J., Kara, S., Hauschild, M. and Kellens, K., 2012. Towards energy and resource efficient manufacturing: A processes and systems approach. CIRP Annals, 61(2), 587-609.
  6. Dymek, S., Wróbel, M., Dollar, M. and Blicharski, M., 2006. Influence of plastic deformation and prolonged ageing time on microstructure of a Haynes 242 alloy. Journal of Microscopy, 224(1), 24-26.
  7. Ergul, E. U. and Eminoglu, I., 2020. Power-law fitness scaling on multi-objective evolutionary algorithms: interpretations of experimental results. Soft Computing, 24(5), 3893-3907.
  8. Ergül, E. U., Gezegin, C. and YILDIZ, A., 2019. Yanıt yüzey yöntemi ve genetik algoritma kullanılarak transformatör sargı en sıcak nokta sıcaklığının modellenmesi ve optimizasyonu. Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi, 10(2), 467-480.
  9. Esmaeilpour, R., Kim, H., Park, T., Pourboghrat, F., Agha, A. and Abu-Farha, F., 2020. Effect of hardening law and process parameters on finite element simulation of single point incremental forming (SPIF) of 7075 aluminum alloy sheet. Mechanics & Industry, 21(3), 302. Habeeb, H., Abou-El-Ho, K., Mohamad, B., Ghani, J. A. and Kadirgama, K., 2008. Investigating of tool wear, tool life and surface roughness when machining of nickel alloy 242 with using of different cutting tools. Asian Journal of Scientific Research, 1(3), 222-230.
  10. Kılıçkap, E. and Hüseyinoğlu, M., 2010. Tepki yüzey modeli ve genetik algoritma kullanılar