KaydedilenlerDerginizi ekleyin

Dergiler / Gazi Üniversitesi Sağlık Bilimleri Enstitüsü Dergisi / 2022 / Cilt: 4 - Sayı: 3

Formulation Development Studies of Three-Dimensional Printable Filaments Containing Eudragit S100 Polymer with High-Glass Transition Temperature

Cennet DURAN
Diren SARISALTIK YAŞIN
Sevgi TAKKA
Sayfa
143–151
Yayın Tarihi
2022-12-31
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

A higher screw speed accelerated the output of the filaments while minimizing the filament diameter variability, which is a requirement for providing uninterrupted printing.In conclusion, the filaments containing Eudragit S100 were successfully and reproducibly printed into round-shaped tablets after modification of the extruder and improvement of the formulation development processes.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:The aim of this study is to examine the formulation, process, and equipment conditions to obtain printable filaments for fused-deposition modelling three-dimensional printing (FDM-3DP) using Eudragit-S100 polymer, which is widely used in the pharmaceutical field and has a high glass transition temperature (Tg).The filaments were extruded by a modified simple single screw extruder.
📊
Temel Bulgular & Veri:Structural integrity and homogeneity of filaments and the printed tablets were demonstrated by SEM.
💡
Sonuç & Katkı:A higher screw speed accelerated the output of the filaments while minimizing the filament diameter variability, which is a requirement for providing uninterrupted printing.In conclusion, the filaments containing Eudragit S100 were successfully and reproducibly printed into round-shaped tablets after modification of the extruder and improvement of the formulation development processes.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Three-dimensional printing · Fused-deposition modelling · Hot-melt extrusion

Abstract

The aim of this study is to examine the formulation, process, and equipment conditions to obtain printable filaments for fused-deposition modelling three-dimensional printing (FDM-3DP) using Eudragit-S100 polymer, which is widely used in the pharmaceutical field and has a high glass transition temperature (Tg).The filaments were extruded by a modified simple single screw extruder. The influence of powder preparation processes such as pre-plastification, sieving, drying, and the formulation factors, such as types and amounts of excipients on the quality of filaments were evaluated. The mechanical properties of filaments were determined manually. Structural integrity and homogeneity of filaments and the printed tablets were demonstrated by SEM. Finally, the printability of the filaments was shown by producing the tablets using an FDM-3D Printer.When combining triacetin and citric acid, extrudable formulations with an adequate plastification were obtained. Magnesium stearate increased the output speed of the filament through the nozzle of the extruder. Furthermore, it was seen that simple modifications on the extruder and powder preparation process improved the printability of the filaments. A higher screw speed accelerated the output of the filaments while minimizing the filament diameter variability, which is a requirement for providing uninterrupted printing.In conclusion, the filaments containing Eudragit S100 were successfully and reproducibly printed into round-shaped tablets after modification of the extruder and improvement of the formulation development processes.

🔖

Bu Makaleye Atıf Yap

DURAN, C., YAŞIN, D. S., TAKKA, S. (2022). Formulation Development Studies of Three-Dimensional Printable Filaments Containing Eudragit S100 Polymer with High-Glass Transition Temperature. Gazi Üniversitesi Sağlık Bilimleri Enstitüsü Dergisi, Cilt: 4 - Sayı: 3, 143–151. https://ajindex.com/articles/868244

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (9)

  1. Beck, R.C.R., Chaves, P.S., Goyanes, A., Vukosavljevic, B., Buanz, A., Windbergs, M., et al. (2017) 3D printed tablets loaded with polymeric nanocapsules: An innovative approach to produce customized drug delivery systems. International Journal of Pharmaceutics, 528(1-2),268-79.
  2. Bruce, L.D., Shah, N.H., Malick, A.W., Infeld, M.H., McGinity, J.W. (2005). Properties of hot-melt extruded tablet formulations for the colonic delivery of 5-aminosalicylic acid. European Journal of Pharmaceutics and Biopharmaceutics, 59(1),85-97.
  3. Carlier, E., Marquette, S., Peerboom, C., Denis, L., Benali, S., Raquez, J.M. et al. (2019). Investigation of the parameters used in fused deposition modelling of poly (lactic acid) to optimize 3D printing sessions. International Journal of Pharmaceutics, 565,367-77.
  4. Chai, X.Y., Chai, H.Y., Wang, X.Y., Yang, J.J., Li, J., Zhao, Y., et al. (2017) Fused Deposition Modelling (FDM) 3D Printed Tablets for Intragastric Floating Delivery of Domperidone. Scientific Reports,7. Elkasabgy, N.A., Mahmoud, A.A., Maged, A. (2020). 3D printing: An appealing route for customized drug delivery systems. International Journal of Pharmaceutics, 588. Genina, N., Hollander, J., Jukarainen, H., Makila, E., Salonen, J., Sandler, N. (2016). Ethylene vinyl acetate (EVA) as a new drug carrier for 3D printed medical drug delivery devices. European Journal of Pharmaceutical Sciences, 90,53-63.
  5. Gioumouxouzis, C.I., Chatzitaki, A.T., Karavasili, C., Katsamenis, O.L., Tzetzis, D., Mystiridou, E. et al. (2018). Controlled Release of 5-Fluorouracil from Alginate Beads Encapsulated in 3D Printed pH-Responsive Solid Dosage Forms. AAPS PharmSciTech, 19(8),3362-75.
  6. Goyanes, A., Martinez, P.R., Buanz, A., Basit, A.W., Gaisford, S. (2015) Effect of geometry on drug release from 3D printed tablets. International Journal of Pharmaceutics, 494(2),657-63.
  7. Goyanes, A., Fina, F., Martorana, A., Sedough, D., Gaisford, S., Basit, A.W. (2017) Development of modified release 3D printed tablets (printlets) with pharmaceutical excipients using additive manufacturing. International Journal of Pharmaceutics, 527(1-2),21-30.
  8. Kollamaram, G., Croker, D.M., Walker, G.M., Goyanes, A., Basit, A.W., Gaisford, S. (2018) Low temperature fused deposition modelling (FDM) 3D printing of thermolabile drugs. International Journal of Pharmaceutics, 545(1-2),144-52.
  9. Okwuosa, T.C., Stefaniak, D., Arafat, B., Isreb, A., Wan, K.W., Alhnan, M.A. (2016) A Lower Temperature FDM 3D Printing for the Manufacture of