Dergiler / Politeknik Dergisi / 2022 / Cilt: 25 - Sayı: 3

Synthesis and Characterization of Copper Metal Matrix Composite Reinforced with Ceramic Oxide Extracted By The Green Route

Sayfa
1185–1189
Yayın Tarihi
2022-10-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

As the filler material silica is extracted from green route which partially replaces the expensive metal, this work reports a non-toxic, cost effective, light weight and improved mechanical strength substitute for copper metal applications.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:The paper presents the synthesis and characterization of Copper metal matrix composite reinforced with silica using powder metallurgy route.
📊
Temel Bulgular & Veri:The 5%wt of silica is reinforced with copper metal as matrix material. 5% wt Magnesium was added as wetting agent as copper shows poor wettability towards silica.
💡
Sonuç & Katkı:As the filler material silica is extracted from green route which partially replaces the expensive metal, this work reports a non-toxic, cost effective, light weight and improved mechanical strength substitute for copper metal applications.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Agro-waste · Rice husk ash · silica

Özet

The paper presents the synthesis and characterization of Copper metal matrix composite reinforced with silica using powder metallurgy route. The 5%wt of silica is reinforced with copper metal as matrix material. 5% wt Magnesium was added as wetting agent as copper shows poor wettability towards silica. The reinforced silica was extracted from agro waste rice husk ash under controlled conditions of sintering temperature and duration of heating from rice husk ash using alkali extraction method. Reflux method was used to extract nanosilica from silica. Silica and the composite were characterized for microstructural studies, elemental composition and surface morphologies using X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray (EDX) and Transmission Electron Microscopy (TEM). The synthesized copper silica composite was studied for structural, compositional and mechanical properties. The results showed that the copper metal matrix composite reinforced with silica showed improved mechanical behavior and can be used in all such applications where light weight and better mechanical strength from copper metal are expected. As the filler material silica is extracted from green route which partially replaces the expensive metal, this work reports a non-toxic, cost effective, light weight and improved mechanical strength substitute for copper metal applications.

Abstract

The paper presents the synthesis and characterization of Copper metal matrix composite reinforced with silica using powder metallurgy route. The 5%wt of silica is reinforced with copper metal as matrix material. 5% wt Magnesium was added as wetting agent as copper shows poor wettability towards silica. The reinforced silica was extracted from agro waste rice husk ash under controlled conditions of sintering temperature and duration of heating from rice husk ash using alkali extraction method. Reflux method was used to extract nanosilica from silica. Silica and the composite were characterized for microstructural studies, elemental composition and surface morphologies using X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray (EDX) and Transmission Electron Microscopy (TEM). The synthesized copper silica composite was studied for structural, compositional and mechanical properties. The results showed that the copper metal matrix composite reinforced with silica showed improved mechanical behavior and can be used in all such applications where light weight and better mechanical strength from copper metal are expected. As the filler material silica is extracted from green route which partially replaces the expensive metal, this work reports a non-toxic, cost effective, light weight and improved mechanical strength substitute for copper metal applications.

🔖

Bu Makaleye Atıf Yap

LAAD, M. (2022). Synthesis and Characterization of Copper Metal Matrix Composite Reinforced with Ceramic Oxide Extracted By The Green Route. Politeknik Dergisi, Cilt: 25 - Sayı: 3, 1185–1189. https://ajindex.com/articles/862645

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

  1. Laad M., Jatti V., “Investigation into the effect of Aluminium powder on mechanical, tribological and Electrical properties of Al-ABSComposites”,WseasTransactions on Applied and Theoritical Mechanics, E-ISSN: 2224-3429, 10, 47-53
  2. Mallik S., N. Ekere, C. Best, R. Bhatti, “Investigation of thermal management materials for automotive electronic control units”., Appl ThermEng, 31: 355-362, (2011)
  3. A. Molina, T. Wang, C. Zou, Z. Chen, M. Li, W. Wang, et al. “In situ synthesis of TiB2 particulate reinforced copper matrix composite with a rotating magnetic field”., Mater Des, 65: 280-288, (2015)
  4. S. Kumari, A. Kumar, P.R. Sengupta, P.K. Dutta, R.B. Mathur “Improving the mechanical and thermal properties of semi-coke based carbon/copper composites reinforced using carbon nanotubes”., J Adv Mater Lett, 5: 265-271, (2014)
  5. R. Zitoune, M. El Mansori, K. Vijayan “Tribo-functional design of double cone drill implications in tool wear during drilling of copper mesh/CFRP/woven ply”Wear, 302: 1560-1567, (2013)
  6. M. Yusoff, R. Othman, Z. Hussain “Mechanical alloying and sintering of nanostructured tungsten carbide-reinforced copper composite and its characterization” Mater Des, 32: 3293-3298, (2011)
  7. A.A. Thakre, S. Soni “Modeling of burr size in drilling of aluminum silicon carbide composites using response surface methodology”Eng Sci Technol, 19: 1199-1205, (2016)
  8. Wąsik, Mateusz &Karwan-Baczewska, Joanna. “Copper Metal Matrix Composites Reinforced by Titanium Nitride Particles”. Key Engineering Materials. 682: 270-275, (2016)
  9. R. Sathiskumar, N. Murugan, I. Dinaharan, S.J. Vijay “Fabrication and characterization of Cu/B4c surface dispersion strengthened composite using friction stir processing”., 59: 83-89, (2014)
  10. W.V. Sagar, S.L. Samir, W.R. Amit “Modelling of Cu-Al2O3 metal matrix composite prepared by powder metallurgy route”Int. J. Eng. Adv. Technol., 3: 330-332, (2013)
  11. M. Yusoff, R. Othman, Z. Hussain “Mechanical alloying and sintering of nanostructured tungsten carbide-reinforced copper composite and its characterization”Mater. Des., 32: 3293-3298, (2011). [12]Q. Kang, X. He, S. Ren, L. Zhang, M. Wu, C. Guo, W. Cui, X. Qu “Preparation of copper–diamond composites with chromium carbide coatings on diamond particles for heat sink applications”Appl. Therm. Eng., 60: 423-429, (2013). [13]. Zhang, X.H. Qu, X.B. He, B.H. Duan, S.B. Ren, M.L. Qin “Thermo-physical and mechanical properties of high volume fraction SiCp/Cu