Dergiler / Research on Engineering Structures and Materials / 2022 / Cilt: 8 - Sayı: 2

Research on Engineering Structures and Materials

Sayfa
205–222
Yayın Tarihi
2022-10-19
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Friction stir spot welding is thus recommended for the fabrication of hybrid metal/polymer.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:This study compares and optimizes the friction stir clinched and friction stir spot welded hybrid aluminum/acrylonitrile butadiene styrene polymer (Al/ABS) joints.
📊
Temel Bulgular & Veri:The optimum tensile-shear failure loads of the friction stir spot welded, and friction stir clinched Al/ABS joints are 932 and 509 N respectively.
💡
Sonuç & Katkı:Friction stir spot welding is thus recommended for the fabrication of hybrid metal/polymer.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Abstract

This study compares and optimizes the friction stir clinched and friction stir spot welded hybrid aluminum/acrylonitrile butadiene styrene polymer (Al/ABS) joints. The mechanical and fracture behaviors of the respective hybrid joints were investigated. The results show that the friction stir spot welded Al/ABS joint exhibited a higher tensile-shear failure load. The presence of higher deformation (protrusion-aided) and deeper tool profile-induced hole (stress raiser) in the friction stir clinched Al/ABS joint impaired the loadbearing resistance of the joint. The optimum tensile-shear failure loads of the friction stir spot welded, and friction stir clinched Al/ABS joints are 932 and 509 N respectively. Three fracture modes, namely unbuttoning, circumferential-partial Al in-polymer shearing, and mid-nugget shearing modes, ensue in both joint categories. Protrusion-aided deformation is not desirable for the improved performance of the hybrid Al/ABS joint. Friction stir spot welding is thus recommended for the fabrication of hybrid metal/polymer.

🔖

Bu Makaleye Atıf Yap

OJO, O. O., ADEYERİ, M. K., ADELUSI, A. O. (2022). Research on Engineering Structures and Materials. Research on Engineering Structures and Materials, Cilt: 8 - Sayı: 2, 205–222. https://ajindex.com/articles/588814

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (10)

  1. Celalettin Y, Fatih K, Nurettin Y, Oguz D. A review on advanced joining techniques of multimaterial part manufacturing for automotive industry. International Journal of Material and Production Engineering, 2015; 5: 63-68
  2. Zhang Y, He X, Way Y, Lu Y, Gu F, Ball A. Study on failure mechanism of mechanical clinching in aluminum sheet materials. The international journal of advanced manufacturing technology, 2018; 96: 3057 – 3068. https://doi.org/10.1007/s00170- 018-1734-2 [3] Lin P-C, Lin J-W, and Li G-X. Clinching process for aluminum alloy and carbon-fiberreinforced thermoplastic sheets. International Journal of Advanced Manufacturing Technology, 2018; 97: 529-541.
  3. Lambiase F. Joinability of Different Thermoplastic Polymers with Aluminium AA6082 Sheets by Mechanical Clinching. International Journal of Advanced Manufacturing Technology, 2015; 80:1995–2006.
  4. Abibe AB, Sônego M, dos Santos JF, Canto LB, Amancio-Filho ST. On the feasibility of friction-based staking joining method for polymer-metal hybrid structures. Materials & Design, 2016; 92: 632 – 642.
  5. Kah P, Suoranta R, Martikainen J, Magnus C. Techniques for joining dissimilar materials: Metals and polymers. Rev. Adv. Mater. Sci., 2014; 36: 152-164 [7] Huang Y, Meng X, Wang Y, Xie Y, Zhou L. Joining of aluminum alloy and polymer via friction stir lap welding. Journal of Materials Processing Tech., 2018; 257: 148- 154.
  6. Li Y, Bu H, Yang H, Liu G, Yao J, Zhan X. Effect of laser heat input on the interface morphology during laser joining of CFRTP and 6061 aluminum alloy. Journal of Manufacturing Processes, 2020; 50: 366 – 379.
  7. Pereira D, Oliveira JP, Santos TG, Miranda RM, Lourenço F, Gumpinger J, Bellarosa R. Aluminium to Carbon Fibre Reinforced Polymer tubes joints produced by magnetic pulse welding. Composite Structures, 2019; 230: 111512.
  8. Mishra R, Ma ZY. Friction stir welding and processing. Mater. Sci. Eng. R., 2005; 50: 1- 78.
  9. Heinz B, Skrotzki B. Characterization of a friction-stir-welded aluminum alloy 6013. Metallurgical and Materials Transactions B, 2002; 33: 489 - 498.
  10. Somasekharan AC, Murr LE. Characteri