Dergiler / Politeknik Dergisi / 2020 / Cilt: 23 - Sayı: 2

Al-α-Si3N4 Kompozit Malzemelerin Difüzyon Kaynağı

Diffusion Welding of Al-α-Si3N4 Composite Materials

Sayfa
497–503
Yayın Tarihi
2022-10-18
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Test sonuçları kaynak süresi ve kaynak sıcaklığı artarken kaynak arayüzeylerinin kesilme mukavetlerinin de artttığını göstermektedir.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışmada toz metalurjisi metodu ile ile üretilen Al-Si3N4 kompozit malzeme değişen sürelerde, değişen sıcaklıklarda ve 2,5 MPa basınç altında difüzyon kaynağı ile birleştirilmiştir.
📊
Temel Bulgular & Veri:Kompozit malzemeninin kaynaklanabilirliği üzerine α-Si3N4 miktarı ve kaynak parametrelerinin etkilerini belirlemek için numune kaynak arayüzeyleri üzerinden optic mikroskop incelemeleri ve kesme testleri yapılmıştır.
💡
Sonuç & Katkı:Test sonuçları kaynak süresi ve kaynak sıcaklığı artarken kaynak arayüzeylerinin kesilme mukavetlerinin de artttığını göstermektedir.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

Bu çalışmada toz metalurjisi metodu ile ile üretilen Al-Si3N4 kompozit malzeme değişen sürelerde, değişen sıcaklıklarda ve 2,5 MPa basınç altında difüzyon kaynağı ile birleştirilmiştir. Kompozit malzemeninin kaynaklanabilirliği üzerine α-Si3N4 miktarı ve kaynak parametrelerinin etkilerini belirlemek için numune kaynak arayüzeyleri üzerinden optic mikroskop incelemeleri ve kesme testleri yapılmıştır. Test sonuçları kaynak süresi ve kaynak sıcaklığı artarken kaynak arayüzeylerinin kesilme mukavetlerinin de artttığını göstermektedir. Numunelerin kesilme testi sonuçlarına optimum kaynak parametrelerinde üretilen (% 15 α-Si3N4 içeren numunede 2 saat süreli 640 °C sıcaklıkta üretilen numunede) metal matrisli kompozit malzemelerin difüzyon kaynak tekniği ile matris yapının % 97, 5’ i kadar mukavemette birleştirilebilir olduğunu göstermiştir.

Abstract

In this study, Al--Si3N4 composite, produced by powder metallurgy method, were joined at 2.5 MPa pressure with various weldingtemperatures (620, 630, and 640 °C) and durations (1,1.5, and 2 h.) by diffusion welding method. Optical microscopy examinationwas carried out from welded interfaces and shear tests were also conducted to the sample interfaces to find out the effect of weldingparameters and amount of α-Si3N4 reinforcement on the weldability properties of composite materials. The test results show thatincrease in the welding temperature and duration resulted in increase shear resistance of the welded zone. Results indicated thatoptimum parameters (welding temperatures, durations and amount of α-Si3N4 are 640 °C, 2 h., and 15wt % respectively) MMCsproduced in this study could be joined by diffusion welding technique successfully with the 97.5 % strength of base material.

🔖

Bu Makaleye Atıf Yap

AYDIN, M., ERDEN, İ. O., ARIK, H. (2022). Al-α-Si3N4 Kompozit Malzemelerin Difüzyon Kaynağı. Politeknik Dergisi, Cilt: 23 - Sayı: 2, 497–503. https://ajindex.com/articles/588447

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (14)

  1. Ozan S., Karaoglu S., Ipek R., “Examination of diffusion welding capabilities of particle-reinforced aluminumbased metal matrix composites”, Engineer and Machine, 53: 45-53, (2012)
  2. Arık H., Sandal R., “Investigation regarding Al-Al2O3 composite material production and its weldability to aluminium by diffusion welding”, GU J Sci, Part A, 4(4): 101-111, (2017)
  3. Arik H., “Production and characterization of in situ Al4C3 reinforced aluminium-based composite produced by mechanical alloying technique”, Materials & Design, 25: 31- 40, (2004)
  4. Mahajan G. V., Aher V. S., “Composite material: A review over current development and automotive application”, International Journal of Scientific and Research Publications, 2(11): 1-5, (2012)
  5. Mollaoglu Altuner H., “Diffusion bonding of particle reinforced aluminum–based metal matrix composites”, Phd. Thesis, Yildiz Technical University, Institute of Sciences, (2011)
  6. Akbulut H., “Production and investigation of microstructure-properties of Al2O3 fibrous reinforced AlSi based composite”, Phd. Thesis, Istanbul Technical University, Institute of Science and Technology, (1994)
  7. Ben R. C., Mirchandani P. K., “New materials by mechanical alloying techniques”, Editors: Arzt E, and Schultz C, Colw-Hirson (FRG) 1988
  8. Zhang X. P., Ye L., Mai W., “Investigation on diffusion bonding characteristics of SiC particulate reinforced aluminum metal matrix composites”, Composites Applied Science and Manufacturing Part A, 30: 1415- 1421, (1999)
  9. Arık H., Turker M, Saritas S., “Investigation of mechanical properties of in situ Al4C3 reinforced aluminium based composites by mechanical alloying technique”, Powder Metallurgy World Congress and Exhibition, Kyoto, 543-549, (2000)
  10. Singer R. F., Oliver W. C., Nix W. D., “Identification of dispersoid phases created in aluminum during mechanical alloying”, Metallurgical Transactions A, 11A: 1895- 1901, (1980)
  11. Ellis B. D., “Joining of aluminum based metal matrix composites”, International Materials Reviews, 41: 41- 58, (1996)
  12. Zhang X. P., Quan G. F., Wei W., “Preliminary investigation on joining performance of SiCp reinforced aluminum metal matrix composite (Al/SiC-MMC) by vacuum brazing”, Composites, Applied Science and Manufacturing Part A, 30: 823-827, (1999)
  13. Huang Y., Ridley N., Humphreys F. J., “Diffusion bonding of superplastic 7075 aluminium alloy”, Materials Science And Engineering A, 266: 295-302, (1999)
  14. Dunkerton S. B., “Diffus