KaydedilenlerDerginizi ekleyin

Dergiler / Istanbul University Journal of Electrical and Electronics Engineering / 2002 / Cilt: 2 - Sayı: 2

Research on large torque traveling wave ultrasonic motor

Gu CHENGLIN
Li HUAFENG
Sayfa
489–493
Yayın Tarihi
2022-10-18
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Experimental results indicate that some significant improvement in the torque performance characteristic can be achieved.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:To increase the torque of a travelling wave type ultrasonic motor (USM), a special $Gamma$-shaped support structure is proposed and studied.
📊
Temel Bulgular & Veri:Its effect on the transverse amplitude and the contact area of the stator and rotor has been studied by FEM.
💡
Sonuç & Katkı:Experimental results indicate that some significant improvement in the torque performance characteristic can be achieved.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Abstract

To increase the torque of a travelling wave type ultrasonic motor (USM), a special $Gamma$-shaped support structure is proposed and studied. Its effect on the transverse amplitude and the contact area of the stator and rotor has been studied by FEM. In addition, to enhance the motor torque further, a twinvibrator structure is equipped. Experimental results indicate that some significant improvement in the torque performance characteristic can be achieved.

🔖

Bu Makaleye Atıf Yap

CHENGLIN, G., HUAFENG, L. (2022). Research on large torque traveling wave ultrasonic motor. Istanbul University Journal of Electrical and Electronics Engineering, Cilt: 2 - Sayı: 2, 489–493. https://ajindex.com/articles/543928

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (14)

  1. Pierce, L., W., “Hottest Spot Temperatures in Ventilated Dry Type Transformers”, IEEE Transactions on Power Delivery, Vol. 9., No. 1., pp. 257-263, January 1994
  2. Pierce, L., W., “Specifying and Loading Cast-Resin Transformers”, IEEE Transactions on Industry Applications, Vol.29., No. 3., pp. 590-599, May/June, 1994
  3. ANSI, 1981. American National Standard-Guide for Loading Mineral-Oil Immersed Overhead and Pad-Mounted Distribution Transformers,c57,91
  4. CEI-IEC354 International Standard, 1991.Loading Guide for Oil-Immersed Power Transformers
  5. Gotter, G., “Erwärmung und Kühlung Elektrischer Maschinen”, Springer-Verlag, 1954
  6. Preiningerova, S.V., Pivrnec, M., “Temperature Distribution in the Coil of a Transformer Winding”, Proccedings of the IEE, Vol. 124, No.3, pp. 218-222, March 1977
  7. Kömürgöz, G., Özkol, Ý., Güzelbeyoðlu, N., “ Temperature Distribution in The Disc-Type Coil of Transformer Winding”, ELECO’2001, Second International Conference on Electrical and Electronics Engineering, pp. 67-71, 2001
  8. Karsai,K., Kerènyi, D., Kiss, L., “Large Power Transformers”, Elsevier,1987
  9. Lobenstein, G., “Zur Heißpunktbestimmung in großen Transformatorenspulen”, Electrie 44, pp. 34-36, 1990
  10. Lobenstein, G., “Die Darstellung des Wärmeübergangskoffizienten im Öltransformator mit kriteriellen Potenzfunktionen”, Electrie 33, pp. 218-220, 1979
  11. Pierce, L., W., “Predicting Hottest Spot Temperatures in Ventilated Dry Type Transformer Windings”, IEEE Transactions on Power Delivery, Vol. 9., No. 2., pp. 1160-1171, April 1994
  12. Pierce, L.W., 1992. An Investigation of the Temperature Distribution in Cast-Resin Transformer Windings, IEEE Transactions on Power Delivery, Vol.7, No.2, 920-926
  13. Hwang, M.D.,Grady, W.M., Sanders, H.W., “Calculation of Winding Temperatures in Distribution Transformers Subjected to Harmonic Currents”, IEEE Transactions on Power Delivery, Vol. 3., No. 3., pp. 1074-1079, July 1988
  14. Incropera, F.P., DeWitt, D.P., “Introduction to Heat Transfer”, John Willey&Sons, 1996.