Dergiler / Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji / 2017 / Cilt: 5 - Sayı: 1

Toz Altı Ark Kaynak Yöntemiyle Üretilen API 5L X70 Kalite Çelik Boruların Mikroyapı ve Mekanik Özellikleri

Microstructure and Mechanical Properties of API 5L X70 Grade Steel Pipes Produced by Submerged Arc Welding Method

Sayfa
55–64
Yayın Tarihi
2022-10-18
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Charpy darbe testleri en yüksek kırılma tokluğunun ana malzemede, en düşük kırılma tokluğunun ise kaynak metalinde olduğunu göstermiştir

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışmada; API 5L X70 rulo sac malzemeler toz altı ark kaynak yöntemi ile birleştirilmiştir.
📊
Temel Bulgular & Veri:Mikroyapı fotoğrafları kaynak metalinde farklı büyüklükte tane yapısının, ITAB'da iri taneli bölgede iri ve girift, şekilsiz tane yapısının, ince taneli bölgede ise homojen dağılımlı eş eksenel tane yapısının hâkim olduğunu göstermiştir.
💡
Sonuç & Katkı:Charpy darbe testleri en yüksek kırılma tokluğunun ana malzemede, en düşük kırılma tokluğunun ise kaynak metalinde olduğunu göstermiştir
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

Bu çalışmada; API 5L X70 rulo sac malzemeler toz altı ark kaynak yöntemi ile birleştirilmiştir. Birleştirilen numunelerin makroyapı, mikroyapı ve mekanik özellikleri incelenmiştir. Mekanik özelliklerin belirlenebilmesi için numunelere çekme, sertlik, Charpy darbe ve eğme testleri uygulanmıştır. Makroyapı incelemeleri birleştirmede tam nüfuziyetin sağlandığını göstermiştir. Mikroyapı fotoğrafları kaynak metalinde farklı büyüklükte tane yapısının, ITAB'da iri taneli bölgede iri ve girift, şekilsiz tane yapısının, ince taneli bölgede ise homojen dağılımlı eş eksenel tane yapısının hâkim olduğunu göstermiştir. Çekme testleriyle kaynaklı birleştirilen numunelerin akma ve maksimum çekme dayanımı değerlerinin ana malzemeden daha yüksek olduğu belirlenmiştir. Sertlik testleri sonucuna göre en yüksek sertlik değerleri kaynak metalinde ölçülmüştür. Charpy darbe testleri en yüksek kırılma tokluğunun ana malzemede, en düşük kırılma tokluğunun ise kaynak metalinde olduğunu göstermiştir

Abstract

In this study, API 5L X70 steel roll materials welded via submerged arc welding technique (SAW). Macrostructure, microstructure and mechanical properties of welded samples were investigated. Tensile, hardness, Charpy impact and bending tests were performed to determine of mechanical properties. Macrostructure analyses showed that full penetration was achieved on welded parts. Microstructure images showed that fine grain structures were formed in weld metal, large, complex and amorphous grain structures were dominated in the coarse grain region, whereas homogeneously distributed coaxial grain structures were dominated in the fine grained region in HAZ. In addition, it was observed from tensile test that yield and maximum tensile strength values of welded parts were higher than the main metals. According to the hardness tests, the highest hardness values were measured on the weld metal. Charpy impact tests showed that the highest fracture toughness values were measured on the main material, the lowest fracture toughness values were measured on the welded metal

🔖

Bu Makaleye Atıf Yap

AKSÖZ, S., ÖZER, A., ADA, H. (2022). Toz Altı Ark Kaynak Yöntemiyle Üretilen API 5L X70 Kalite Çelik Boruların Mikroyapı ve Mekanik Özellikleri. Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji, Cilt: 5 - Sayı: 1, 55–64. https://ajindex.com/articles/522214

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. Bai, Y., “Pipelines and Risers”, Elsevier, Oxford, UK, 2001
  2. Baek, J.H., Kim, Y.P., Kim, K., Kim, C.M., Kim W.S. and Seok C.S., "Effects of pre-strain on the Mechanical Properties of API 5L X65 Pipe" Materials Science and Engineering(A), Cilt 527, 1473- 1479, 2010
  3. Baek, J., Kima, Y., Kima, W., Koo, J., Seok, C., “Load bearing capacity of API X65 pipe with dent defect under internal pressure and in-plane bending”, Materials Science and Engineering A, Cilt 540, 70–82, 2012
  4. Cosham, A., Hopkins, P., “The effect of dents in pipelines guidance in the pipeline defect assessment manual”, International Journal of Pressure Vessels and Piping, Cilt 81, 127– 139, 2004
  5. Ada, H., Aksöz, S., Fındık, T., Çetinkaya, C., Bostan, B. and Candan, İ., “The investigation of effect of welding process on the microstructure and mechanical properties of API 5L X65 steel welded with gas metal arc welding method”, 4th International Conference on Welding Technologies and Exhibition, Gaziantep, 674 – 683, 11-13 Mayıs 2016
  6. Aksöz, S., Ada, H., Fındık, T., Çetinkaya, C., Bostan, B. and Candan, İ., “The investigation of effect of welding process on the microstructure and mechanical properties of API 5L X65 steel welded with electric arc welding method”, 4th International Conference on Welding Technologies and Exhibition, Gaziantep, 684 – 693, 11-13 Mayıs 2016
  7. API Specifications 5L, “Specifications for Line Pipe”. 45th Edition, American Petroleum Institute, USA, 2012
  8. Hashemi, S.H., "Strength - hardness statistical correllation in API X65 steel", Mater. Sci. Eng. A, Cit 528: 1648–1655, 2011
  9. Hashemi, S.H., Mohammadyani, D., “Characterisation of weldmenthardness, impactenergyandmicrostructure in API X65 steel”, Int. J. Pressure Vessels Piping, Cilt 98: 8–15, 2012
  10. Rakhshkhorshid, M., Hashemi, S.H., “Experimental study of hot deformation behavior in API X65 steel”, Materials Science & Engineering A, Cilt 573:37–44, 2013
  11. Bajicand, N.V. Šijaki-Žeravi, “The analysis of change of structural and mechanical properties of welded joints of microalloyed Nb/V steel grade by changing the composition of filler material”, Internat. Conf. On Welding, Belgrade, 2003
  12. Bajic, N., Sijacki-Zeravcic, V., Rakin, M., and Kovacevic, K., “Structure optimization of weld metal and HAZ in microalloyed high strength steel welded joints”, Yucomat 2005, Herceg Novi, (ISBN: 86- 80321-08-7), pp. 193–200, 2005
  13. Radovic, A., Bajic, N., and Grabulov, V., “Specific