Dergiler / Research on Engineering Structures and Materials / 2021 / Cilt: 7 - Sayı: 3

Fatigue behavior of flush reinforced welded hand-holes in aluminum light poles

Sayfa
465–480
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

So, the effect of the blowout preventer working condition on shear force requirement for shear operation could be accurately approximated by simulating the entire process, and ram geometry could be optimized to reduce force and energy used to shear the tube by plastic deformation.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Hand-holes are used in welded aluminum light poles which provide access to electrical wiring for both maintenance and installation.
📊
Temel Bulgular & Veri:Specimens were constructed with a “flush” hand-hole utilizing reinforcement placed on the inside of the tube, with the handhole located 18 in from the base.
💡
Sonuç & Katkı:So, the effect of the blowout preventer working condition on shear force requirement for shear operation could be accurately approximated by simulating the entire process, and ram geometry could be optimized to reduce force and energy used to shear the tube by plastic deformation.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

Hand-holes are used in welded aluminum light poles which provide access to electrical wiring for both maintenance and installation. Light poles are usually slender and subjected to cyclic loading due to the response from wind. In the field, localized fatigue cracking around hand-holes has been observed but few studies have focused on the resistance of welded aluminum hand-holes. In this study, three-point bending fatigue tests were conducted on full-scale light poles samples. Specimens were constructed with a “flush” hand-hole utilizing reinforcement placed on the inside of the tube, with the handhole located 18 in from the base. Five of these poles, each containing two separate details were tested. Among the ten details that were tested, eight failed as a result of fatigue cracking and the resulting data is compared to current design S-N curves of the Aluminum Design Manual (ADM). A finite element model was created to help understand the local stresses around the hand-hole. this study, the estimation of shear force for blind shear ram type blowout preventer was investigated by using Finite Element Method (FEM). So, the effect of the blowout preventer working condition on shear force requirement for shear operation could be accurately approximated by simulating the entire process, and ram geometry could be optimized to reduce force and energy used to shear the tube by plastic deformation.

🔖

Bu Makaleye Atıf Yap

RUSNAK, C. R., MENZEMER, C. C. (2021). Fatigue behavior of flush reinforced welded hand-holes in aluminum light poles. Research on Engineering Structures and Materials, Cilt: 7 - Sayı: 3, 465–480. https://ajindex.com/articles/389558

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (12)

  1. Murthy MVV, Rao KP, Rao AK. On stresses around an arbitrarily oriented crack in a cylindrical shell. Int J Solids Struct 1974; 10: 1243-1269.
  2. Durelli AJ, Parks VJ, Feng HC. Stresses around an elliptical hole in a finite plate subjected to axial loading. J Appl Mech 1966; 33: 192-195.
  3. Aluminum Design Manual: Specification for Aluminum Structures. The Aluminum Association, Arlington, VA, USA; 2010
  4. Fisher JW, Kulak GL, Smith IFC. A fatigue primer for structural engineers. National Steel Bridge Alliance: AISC; 1998
  5. AASHTO (American Association of State Highway and Transportation Officials). Standard specifications for structural supports for highway signs, luminaires and traffic signals (LRFDLTS-1), Washington, DC, USA; 2015
  6. Roy S, Park YC, Sause R, Fisher JW, Kaufmann EJ. Cost-effective connection details for highway sign, luminaire, and traffic signal structures. NCHRP 10-70 web-only Doc. 176, Transportation Research Board, Washington, DC, USA; 2011
  7. Dexter RJ, Ricker NJ. Fatigue-resistant design of cantilevered signal, sign, and light supports, NCHRP Rep 469. Univ of Minnesota, Minneapolis, MN, USA; 2002
  8. Menzemer C. Examination of several Mullica river bridge light poles, corresponding to J. Bowman, Hapco, USA; 2012 [9] Daneshkhah AR, Schlatter CR, Rusnak CR, Menzemer CC. Fatigue behavior of reinforced welded hand-holes in aluminum light poles. Engineering Structures and Materials Vol 188.
  9. Rusnak CR. Fatigue behavior in reinforced electrical access holes in aluminum light pole support structures. Master’s thesis, the University of Akron, Akron, OH, USA; 2019
  10. Taghipoor H, Damghani Nouri M. Axial crushing and transverse bending responses of sandwich structures with lattice core. J Sandw Struct Mater [Internet]. 2018 Feb 26.
  11. Taghipoor H, Noori MD. Experimental and numerical study on energy absorption of lattice-core sandwich beam. Steel Compos Struct [Internet]. 2018;27(2):135–47 [13] Taghipoor H, Eyvazian A, Ghiaskar A, Praveen Kumar A, Magid Hamouda A, Gobbi M. Experimental and numerical study of lattice-core sandwich panels under low-speed impact. Mater Today Proc [Internet]. 2020 Mar;27(xxxx):1487–92.
  12. Hilty E, Menzemer C, Manigandan K, Srivatsan T. Influence of welding and heat treatment on m