Dergiler / Politeknik Dergisi / 2019 / Cilt: 22 - Sayı: 4

The Effect of Mechanical Properties and the Cutting Parameters on Machinability of AISI 5140 Steel Cooled at High Cooling Rates After Hot Forging

Sayfa
879–887
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

While the highest Fc were reached in the workpiece with the highest hardness cooled in the polymerized water after hot forging, the lowest surface roughness (Ra) was obtained in the same workpiece.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, the effect of mechanical properties and cutting parameters (Cp) on the machinability of AISI 5140 steel cooled at high cooling rates after hot forging was investigated.
📊
Temel Bulgular & Veri:The microstructural examinations and hardness measurements of the as-received AISI 5140 steel and the workpieces cooled in the oil and polymerized water after hot forging were performed.
💡
Sonuç & Katkı:While the highest Fc were reached in the workpiece with the highest hardness cooled in the polymerized water after hot forging, the lowest surface roughness (Ra) was obtained in the same workpiece.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Hot forging · tempered steel AISI 5140 · machinability

Özet

In this study, the effect of mechanical properties and cutting parameters (Cp) on the machinability of AISI 5140 steel cooled at high cooling rates after hot forging was investigated. The microstructural examinations and hardness measurements of the as-received AISI 5140 steel and the workpieces cooled in the oil and polymerized water after hot forging were performed. Turning process was conducted by using a coated ceramic tool at five different cutting speeds (Vc) (120, 150, 180, 210, and 240 m/min), four different feed rates (fn) (0.04, 0.08, 0.12, and 0.16 mm/rev), and four different depths of cut (ap) (0.4, 0.6, 0.8, and 1 mm) under dry machining conditions. SEM examinations of the cutting tools were also performed. It was seen from the results that the changing microstructure and hardness values had a significant effect on cutting forces (Fc) and surface roughness (Ra) from the Cp depending on cooling rate. While the highest Fc were reached in the workpiece with the highest hardness cooled in the polymerized water after hot forging, the lowest surface roughness (Ra) was obtained in the same workpiece.

Abstract

In this study, the effect of mechanical properties and cutting parameters (Cp) on the machinability of AISI 5140 steel cooled at high cooling rates after hot forging was investigated. The microstructural examinations and hardness measurements of the as-received AISI 5140 steel and the workpieces cooled in the oil and polymerized water after hot forging were performed. Turning process was conducted by using a coated ceramic tool at five different cutting speeds (Vc) (120, 150, 180, 210, and 240 m/min), four different feed rates (fn) (0.04, 0.08, 0.12, and 0.16 mm/rev), and four different depths of cut (ap) (0.4, 0.6, 0.8, and 1 mm) under dry machining conditions. SEM examinations of the cutting tools were also performed. It was seen from the results that the changing microstructure and hardness values had a significant effect on cutting forces (Fc) and surface roughness (Ra) from the Cp depending on cooling rate. While the highest Fc were reached in the workpiece with the highest hardness cooled in the polymerized water after hot forging, the lowest surface roughness (Ra) was obtained in the same workpiece.

🔖

Bu Makaleye Atıf Yap

ÖZLÜ, B., DEMİR, H., TÜRKMEN, M. (2019). The Effect of Mechanical Properties and the Cutting Parameters on Machinability of AISI 5140 Steel Cooled at High Cooling Rates After Hot Forging. Politeknik Dergisi, Cilt: 22 - Sayı: 4, 879–887. https://ajindex.com/articles/307359

Kaynakça (2)

  1. Hu C.L., Zhao Z., Gong A.J., Shi W.B., “Effect of Warm Deformation Parameters and Cooling Rates on the Recrystallization Transformation Microstructure in 40Cr Steel”, Journal of Materials Engineering and Performance, 24: 505-516, (2015)
  2. Ceschini L., Marconi A., Martini C., Morr A., Schino A., “Tensile and Impact Behaviour of A Microalloyed Medium Carbon Steel: Effect of The Cooling Condition and Corresponding Microstructure”, Materials & Design, 45: 171-178, (2013).[3] Ulas H.B., Bilgin M., Sezer M.B., Özkan M.T., Performance of Coated and Uncoated Carbide/Cermet Cutting Tools During Turning”, Materials Testing 60: 893-901, (2018).[4] Shalaby M.A., El Hakim M.A., Abdelhameed M.M., Krzanowski J.E., Veldhuis S.C. Dosbaevad G.K., “Wear Mechanisms of Several Cutting Tool Materials in Hard Turning of High Carbon-Chromium Tool Steel”, Tribology International, 70: 148-154, (2014).[5] Tang L., Cheng Z., Huang J., Gao C., Chang W., “Empirical Models For Cutting Forces in Finish Dry Hard Turning of Hardened Tool Steel at Different Hardness Levels”, The International Journal of Advanced Manufacturing Technology, 76:691-703, (2015).[6] Bartarya G., Choudhury S.K., “State of The Art in Hard Turning”, International Journal of Machine Tools and Manufacture, 53: 1-14, (2012).[7] Meddour I., Yallese M.A., Khattabi R., Elbah M., Boulanouar L., “Investigation and Modeling of Cutting Forces and Surface Roughness When Hard Turning of AISI 52100 Steel With Mixed Ceramic Tool: Cutting Conditions Optimization”, The International Journal of Advanced Manufacturing Technology, 77: 1387-1399, (2015).[8] Bouacha K., Yallese M.A., Mabrouki T., Rigal J.F., “Statistical Analysis of Surface Roughness and Cutting Forces Using Response Surface Methodology in Hard Turning of AISI 52100 Bearing Steel With CBN Tool”, International Journal of Refractory Metals and Hard Materials, 28: 349-361, (2010).[9] Grzesik W., Wanat T., “Comparative Assessment of Surface Roughness Produced by Hard Machining With Mixed Ceramic Tools Including 2D and 3D Analysis”, Journal of Materials Processing Technology, 169: 364-371, (2005).[10] Oliveira A.J., Diniz A.E., Ursolino D.J., “Hard Turning in Continuous and İnterrupted Cut With PCBN and Whisker-Reinforced Cutting Tools”, Journal of Materials Processing Technology, 209: 5262-5270, (2009).[11] Aouici H., Yallese M.A., Chaoui K., Mabrouki T., Rigal J.F., “Analysis of Surface Roughness and Cutting Force Components in Hard Turning With CBN Tool: Prediction