Dergiler / Politeknik Dergisi / 2021 / Cilt: 24 - Sayı: 2

Elektro Erozyonla Tornalama Yöntemiyle İşlenen Soğuk İş Takım Çeliğinin Yorulma Ömrünün Tahmini

Estimation of Fatigue Life of Cold Work Tool Steel Machined by Electrical Discharge Turning

Sayfa
495–502
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Taguchi analizine göre optimum teorik yorulma gerilmesi A1Ton1Toff3 deney dizisinde işlenen parça için √area modeli ile 643.932 MPa olarak hesaplanmıştır.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışmada, elektro erozyon ile tornalamada (EET) işleme parametrelerinin yüzey bütünlüğü ve işlenmiş parçanın yorulma ömrüne etkilerinin belirlenmesi amaçlanmıştır.
📊
Temel Bulgular & Veri:EET deneyleri, AISI L2 takım çeliği üzerinde üçer farklı boşalım akımı, vurum süresi ve bekleme süresi ile sabit devir sayısı kullanılarak yapılmıştır.
💡
Sonuç & Katkı:Taguchi analizine göre optimum teorik yorulma gerilmesi A1Ton1Toff3 deney dizisinde işlenen parça için √area modeli ile 643.932 MPa olarak hesaplanmıştır.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Elektro erozyon · Tornalama · Yüzey pürüzlülüğü

Özet

Bu çalışmada, elektro erozyon ile tornalamada (EET) işleme parametrelerinin yüzey bütünlüğü ve işlenmiş parçanın yorulma ömrüne etkilerinin belirlenmesi amaçlanmıştır. İlk olarak, iş parçasının dönmesini sağlamak amacıyla bir mekanizma tasarlanarak imal edilmiştir. EET deneyleri, AISI L2 takım çeliği üzerinde üçer farklı boşalım akımı, vurum süresi ve bekleme süresi ile sabit devir sayısı kullanılarak yapılmıştır. Deneyler, L9 dikey dizisine göre yapılmış olup, işleme performans çıktıları olarak Rz, Sm ve sertlik değerleri ölçülmüştür. Son olarak, √area modeli uygulanarak işlenen parçaların yorulma ömrü tahmin edilmiş ve işleme parametrelerine göre teorik yorulma ömrünün değişimi araştırılmıştır. Deneysel sonuçlara göre, boşalım akımı ve vurum süresinin artmasıyla Rz ve Sm parametrelerinde bir artış belirlenmiştir. En düşük Rz ve Sm değerleri 3 A boşalım akımı, 3µs vurum süresi ve 5 µs bekleme süresinde elde edilmiştir. Taguchi analizine göre optimum teorik yorulma gerilmesi A1Ton1Toff3 deney dizisinde işlenen parça için √area modeli ile 643.932 MPa olarak hesaplanmıştır.

Abstract

In this study, it was aimed to determine the effects of machining parameters on the surface integrity and fatigue life of the machined part in electrical discharge turning (EDT). Initially, a mechanism was designed and manufactured to ensure rotation of the workpiece. EDT experiments were carried out on AISI L2 tool steel using three different discharge currents, pulse on time, pulse off time and constant rotational speed. The experiments were carried out according to the L9 orthogonal array, and Rz, Sm and hardness values were measured as processing performance outputs. Finally, the fatigue life of the machined parts was estimated by applying the √area model and the change of theoretical fatigue life according to the machining parameters was investigated. According to experimental results, an increase in Rz and Sm parameters was determined with increasing the discharge current and pulse on time. The lowest Rz and Sm values were obtained at 3 A discharge current, 3 µs pulse on time and 5 µs pulse off time. Based on Taguchi analysis, the optimum theoretical fatigue stress was calculated as 643.932 MPa with √area model for the machined workpiece in the A1Ton1Toff3 experiment sequence.

🔖

Bu Makaleye Atıf Yap

ÇAKIROĞLU, R., GÜNAY, M. (2021). Elektro Erozyonla Tornalama Yöntemiyle İşlenen Soğuk İş Takım Çeliğinin Yorulma Ömrünün Tahmini. Politeknik Dergisi, Cilt: 24 - Sayı: 2, 495–502. https://ajindex.com/articles/307014

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. Davim, J. Paulo, “Surface integrity in machining”. Springer, Vol. London:1848828742, (2010
  2. Rasti, A., Sadeghi, M. H., & Farshi, S. S. “An investigation into the effect of surface integrity on the fatigue failure of AISI 4340 steel in different drilling strategies”, Engineering Failure Analysis, 95, 66-81, (2019
  3. Pramanik, A., & Basak, A. K. “Effect of wire electric discharge machining (EDM) parameters on fatigue life of Ti-6Al-4V alloy”, International Journal of Fatigue, 128, 105186, (2019
  4. Tekaüt, İ., “Theoretical Evaluation of the Effect of Surfaces Processed with Abrasive Water Jet on Fatigue Life”, Transactions of FAMENA, 43(2), 85-98.), (2019
  5. Jawahir IS, Brinksmeier E, M’Saoubi R, Aspinwall DK, Outeiro JC, Meyer D, et al. “Surface integrity in material removal processes: Recent advances”, CIRP Ann - Manuf Technol, (2011
  6. Amorim FL, Weingaertner WL, “The behavior of graphite and copper electrodes on the finish die-sinking electrical discharge machining (EDM) of AISI P20 tool steel”, J Brazilian Soc Mech Sci Eng, 29:366–71,(2007
  7. Ho KH, Newman ST., “State of the art electrical discharge machining (EDM)”, Int J Mach Tools Manuf., (2003
  8. Erdem, O., Çoğun, C., Urtekin, L., Özerkan, H. B., & Uslan, İ. Toz katkılı ve ısıtılmış dielektriğin elektro erozyon ile işlemede (EEİ) delik delme performansı üzerine etkisi, “Journal of the Faculty of Engineering and Architecture of Gazi University”, 31(3), 531-544, (2016
  9. Cogun, C., Esen, Z., Genc, A., Cogun, F., & Akturk, N., “Effect of powder metallurgy Cu-B4C electrodes on workpiece surface characteristics and machining performance of electric discharge machining”, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 230(12), 2190-2203, (2016
  10. Gohil V, Puri YM., “Turning by electrical discharge machining: A review”, Proc Inst Mech Eng Part B J Eng Manuf; 231:195–208, (2017
  11. Gupta K, Gupta MK., “Developments in nonconventional machining for sustainable production: A state-of-the-art review”, Proc Inst Mech Eng Part C J Mech Eng Sci., 233:4213–32, (2019
  12. Kumar, R., Roy, S., Gunjan, P., Sahoo, A., Sarkar, D. D., & Das, R. K. “Analysis of MRR and surface roughness in machining Ti-6Al-4V ELI titanium alloy using EDM process”, Procedia Manufacturing, 20, 358-364, (2018
  13. Matoorian, P., Sulaiman, S., & Ahmad, M. M. H. M., “An experimental study for optimization of electrical discharge turning (EDT) process”, Journal of