KaydedilenlerDerginizi ekleyin

Dergiler / Politeknik Dergisi / 2017 / Cilt: 20 - Sayı: 1

Influence of Coolant on the Performance of Electro Discharge Hole Drilling

KÜRŞAD GÖV
Sayfa
191–196
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The results indicated that machining speed 101 mg/min, electrode wear 4,9 mg/min and surface roughness value Ra 2,7 μm were obtained by using distilled-water at 10 A current level.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In the present study, a comparative study of hole-EDM drilling of die steel, namely as DIN 1.2080 using electrical discharge machining method was performed in order to discover the effects of coolant types, namely distilled-water, kerosene and water.
📊
Temel Bulgular & Veri:The electrical parameters of electrical discharge machining process were taken as constant. the performance parameters were defined as machining speed, electrode wear, surface roughness value (Ra) and white layer thickness.
💡
Sonuç & Katkı:The results indicated that machining speed 101 mg/min, electrode wear 4,9 mg/min and surface roughness value Ra 2,7 μm were obtained by using distilled-water at 10 A current level.
🔬Tür:Araştırma Makalesi
📍Kapsam:2080 Verileri
⚙️Değişkenler:EDM · EDM Drilling · Coolant

Özet

In the present study, a comparative study of hole-EDM drilling of die steel, namely as DIN 1.2080 using electrical discharge machining method was performed in order to discover the effects of coolant types, namely distilled-water, kerosene and water. The electrical parameters of electrical discharge machining process were taken as constant. the performance parameters were defined as machining speed, electrode wear, surface roughness value (Ra) and white layer thickness. The experimental results reveal that the increasing the current causes decreasing in machining speed, increasing in white layer thickness, increasing in electrode wear and decreasing in surface quality of electrical discharge machining process. The distilled-water has comparatively better results than the other coolant types. The results indicated that machining speed 101 mg/min, electrode wear 4,9 mg/min and surface roughness value Ra 2,7 μm were obtained by using distilled-water at 10 A current level.

Abstract

In the present study, a comparative study of hole-EDM drilling of die steel, namely as DIN 1.2080 using electrical discharge machining method was performed in order to discover the effects of coolant types, namely distilled-water, kerosene and water. The electrical parameters of electrical discharge machining process were taken as constant. the performance parameters were defined as machining speed, electrode wear, surface roughness value (Ra) and white layer thickness. The experimental results reveal that the increasing the current causes decreasing in machining speed, increasing in white layer thickness, increasing in electrode wear and decreasing in surface quality of electrical discharge machining process. The distilled-water has comparatively better results than the other coolant types. The results indicated that machining speed 101 mg/min, electrode wear 4,9 mg/min and surface roughness value Ra 2,7 μm were obtained by using distilled-water at 10 A current level.

🔖

Bu Makaleye Atıf Yap

GÖV, K. (2017). Influence of Coolant on the Performance of Electro Discharge Hole Drilling. Politeknik Dergisi, Cilt: 20 - Sayı: 1, 191–196. https://ajindex.com/articles/306524

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

  1. Eyercioglu, O., M.V. Cakir, and K. Gov. "Influence of machining parameters on the surface integrity in small-hole electrical discharge machining", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 228(1): 51-61. (2014)
  2. Yusuf Keskin, H., H. Selcuk, and K. Mevlut. "An experimental study for determination of the effects of machining parameters on surface roughness in EDM", International Journal of Advance Manufacturing Technology, 28: 1118-1121. (2006)
  3. Puranik, M.S. and S.S. Joshi. "Analysis of accuracy of high-aspect-ratio holes generated using micro-electric discharge machining drilling", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 222(11): 1453-1464. (2008)
  4. Mujumdar, S.S., S.A. Mastud, R.K. Singh, and S.S. Joshi. "Experimental characterization of the reverse micro-electrodischarge machining process for fabrication of high-aspect-ratio micro-rod arrays", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 224(5): 777-794. (2010)
  5. Kurnia, W., P.C. Tan, S.H. Yeo, and Q.P. Tan. "Surface roughness model for micro electrical discharge machining", Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 223(3): 279-287. (2009)
  6. Yilmaz, O. and M.A. Okka. "Effect of single and multi-channel electrodes application on EDM fast hole drilling performance", The International Journal of Advanced Manufacturing Technology, 51(1-4): 185-194. (2010)
  7. Kuppan, P., A. Rajadurai, and S. Narayanan. "Influence of EDM process parameters in deep hole drilling of Inconel 718", The International Journal of Advanced Manufacturing Technology, 38(1-2):74-84. (2008)
  8. Singh, P.N., K. Raghukandan, M. Rathinasabapathi, and B. Pai. "Electric discharge machining of Al–10% SiC p as-cast metal matrix composites", Journal of materials processing technology, 155: 1653-1657. (2004)
  9. Özgedik, A. "Elektro Erozyon ile İşlemede Tezgah, İşparçası ve Elektrot Üzerinde Uygulanmış Modifikasyonlar", Makine Teknolojileri Elektronik Dergisi, 11(2): 19-38. (2014)
  10. Özkul, İ., U. Şeker, B.B. Buldum, and A. Akkurt. "Sicak İş Takim Çeliklerinden Dievar Takim Çeliğinin Tel Erozyon İle İşlenebilirliliğinin Araştırılması", Makine Teknolojileri Elektronik Dergisi, 9(4): 31-44. (2012)
  11. AY, M. and D. Aydoğdu. "Tel Erozyonda Kesme Parametrelerinin Parçanın Boyut Ölçüsüne Etkileri