Dergiler / Research on Engineering Structures and Materials / 2018 / Cilt: 4 - Sayı: 3

The effect of time delay of fluid flow in a vascularized plate

Sayfa
161–167
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

For instance, 4% decrease in the time required to reach steady-state with the tree-shaped design relative to the parallel design was achieved when the preset temperature for time delay is 90°C.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, we show the effect of time delay of coolant fluid flow into a vascularized plate on the peak temperature.
📊
Temel Bulgular & Veri:In the study, the peak temperatures were monitored and the coolant was pumped when the peak temperature reaches to 50°C, 70°C and 90°C.
💡
Sonuç & Katkı:For instance, 4% decrease in the time required to reach steady-state with the tree-shaped design relative to the parallel design was achieved when the preset temperature for time delay is 90°C.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

In this study, we show the effect of time delay of coolant fluid flow into a vascularized plate on the peak temperature. Coolant flows along vascular channels which were embedded in a rectangular plate. Two kinds of vascular channel designs were investigated experimentally: parallel and tree-shaped. In the study, the peak temperatures were monitored and the coolant was pumped when the peak temperature reaches to 50°C, 70°C and 90°C. The performance comparison of two distinct designs is based on two criteria: the time required for the steady state condition after the coolant is pumped and the peak temperature after the steady state condition is conformed. The results show that the time required to reach steady-state condition increases as the time delay increases. The parallel and tree-shaped designs show similar performance (time required to reach steady state) with slightly improved performance in the tree-shaped design as the preset temperature for time delay increases. For instance, 4% decrease in the time required to reach steady-state with the tree-shaped design relative to the parallel design was achieved when the preset temperature for time delay is 90°C.

🔖

Bu Makaleye Atıf Yap

YENİGÜN, O., COŞKUN, T., ÇETKİN, E. (2018). The effect of time delay of fluid flow in a vascularized plate. Research on Engineering Structures and Materials, Cilt: 4 - Sayı: 3, 161–167. https://ajindex.com/articles/302656

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

  1. Shafahi M, Bianco V, Vafai K, Manca O. Thermal performance of flat-shaped heat pipes using nanofluids. International Journal of Heat and Mass Transfer, 2010; 53: 1438-1445. https://doi.org/10.1016/j.ijheatmasstransfer.2009.12.007
  2. Li Y, Xie HQ, Yu W, Li J. Liquid cooling of tractive lithium ion batteries pack with nanofluids coolant. Journal of Nanoscience and Nanotechnology, 2015; 15(4): 3206-3211. https://doi.org/10.1166/jnn.2015.9672
  3. Alshaer WG, Nada, SA, Rady MA, Del Barrio EP, Sommier A. Thermal management of electronic devices using carbon foam and PCM/nano-composite. International Journal of Thermal Sciences, 2015; 89: 79-86. https://doi.org/10.1016/j.ijthermalsci.2014.10.012
  4. Ma T, Yang HX, Zhang YP, Lu L, Wang X. Using phase change materials in photovoltaic systems for thermal regulation and electrical efficiency improvement: A review and outlook. Renewable and Sustainable Energy Reviews, 2015; 43: 1273-1284. https://doi.org/10.1016/j.rser.2014.12.003
  5. Cetkin E, Lorente S, Bejan A. Vascularization for cooling a plate heated by a randomly moving source. Journal of Applied Physics, 2012; 112(8): 084906, 2012.
  6. Cetkin E, Lorente S, Bejan A. Vascularization for cooling and mechanical strength. International Journal of Heat and Mass Transfer, 2011; 54(13-14): 2774-2781. https://doi.org/10.1016/j.ijheatmasstransfer.2011.02.061
  7. Wang KM, Lorente S, Bejan A. Vascular materials cooled with grids and radial channels. International Journal of Heat and Mass Transfer, 2009; 52(5-6): 1230-1239. https://doi.org/10.1016/j.ijheatmasstransfer.2008.08.027 Cho KH. Fluid flow and heat transfer in vascularized cooling plates. International Journal of Heat and Mass Transfer, 2010; 53(19-20): 3607-3614. https://doi.org/10.1016/j.ijheatmasstransfer.2010.03.027
  8. Rocha LAO, Lorente S, Bejan A. Tree-shaped vascular wall designs for localized intense cooling. International Journal of Heat and Mass Transfer, 2009; 52(19-20): 4535-4544. https://doi.org/10.1016/j.ijheatmasstransfer.2009.03.003
  9. Cetkin E, Lorente S, Bejan A. Hybrid grid and tree structures for cooling and mechanical Strength. Journal of Applied Physics, 2011; 110(6): 064910. https://doi.org/10.1063/1.3626062
  10. Cho KH, Lee J, Ahn HS, Bejan A, Kim MH. Fluid flow and heat transfer in vascularized cooling plates. International Journal of Heat and Mass Transfer, 2010; 53: 3607-3614. https://doi.org/10.1016/j.ijheatmasstransfer.2010.03.027
  11. Cho KH, Chang WP, Kim MH. A numerical and experimental study to evaluate performance of v