Dergiler / Research on Engineering Structures and Materials / 2016 / Cilt: 2 - Sayı: 2

Some properties of Cu-MgO composites produced by powder metallurgy

Sayfa
67–74
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

As a result, optimum electrical conductivity and hardness balance for promising contact material was obtained with the addition of max. 2wt.% of MgO.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Pure Cu matrix composite reinforced with MgO were successfully produced by powder metallurgy method.
📊
Temel Bulgular & Veri:Nano sized MgO particles with 0.5, 1, 2 and 3 wt.% were mixed with copper powder in size of 40 µm mechanically and compacted by applying 220 MPa pressure and sintered at 700°C for 2 hours in an open atmospheric furnace followed by hot pressing with the pressure of 590 MPa.
💡
Sonuç & Katkı:As a result, optimum electrical conductivity and hardness balance for promising contact material was obtained with the addition of max. 2wt.% of MgO.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

Pure Cu matrix composite reinforced with MgO were successfully produced by powder metallurgy method. Nano sized MgO particles with 0.5, 1, 2 and 3 wt.% were mixed with copper powder in size of 40 µm mechanically and compacted by applying 220 MPa pressure and sintered at 700°C for 2 hours in an open atmospheric furnace followed by hot pressing with the pressure of 590 MPa. SEM studies revealed that MgO particles were dispersed homogenously in copper matrix and any oxides of copper matrix were not detected which confirmed by EDS and XRD analyses. With the addition of 3wt.% MgO particles, hardness of composites increased from 89 HVN to 122 HVN while, relative density decreased from 94.2% to 84.1% and electrical conductivity from 90.15 to 43.5 IACS (International Annealed Copper Standard). As a result, optimum electrical conductivity and hardness balance for promising contact material was obtained with the addition of max. 2wt.% of MgO.

🔖

Bu Makaleye Atıf Yap

EFE, G. F. Ç., İPEK, M., ZEYTİN, S., BİNDAL, C. (2016). Some properties of Cu-MgO composites produced by powder metallurgy. Research on Engineering Structures and Materials, Cilt: 2 - Sayı: 2, 67–74. https://ajindex.com/articles/302642

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (9)

  1. Guo X, Song K, Liang S, Zheng C. Thermal expansion behavior of MgO/Cu composite with lower MgO volume fraction, Materials Research Bulletin, 2012;47:3211-3215. http://dx.doi.org/10.1016/j.materresbull.2012.08.012
  2. Efe GC, Ipek M, Zeytin S, Bindal C. An investigation of the effect of SiC particle size on Cu-SiC composites, Composites Part B: Engineering, 2012;43(4):1813-1822. http://dx.doi.org/10.1016/j.compositesb.2012.01.006
  3. Chen B, Yang J, Zhang Q, Huang H, Li H, Tang H, Li C. Tribological properties of copperbased composites with copper coated NbSe2 and CNT, Materials and Design, 2015;75:24-31. http://dx.doi.org/10.1016/j.matdes.2015.03.012
  4. Zhang R, Gao L, Guo J. Effect of Cu2O on the fabrication of SiCp/Cu nanocomposites using coated particles and conventional sintering, Composites: Part A, 2004;35:1301- 1305. http://dx.doi.org/10.1016/j.compositesa.2004.03.021
  5. Efe GFC, Altinsoy I, Ipek M, Zeytin S, Bindal C. Some properties of Cu- SiC composites produced by powder metallurgy method, Kovove Mater, 2011;49:131-136.
  6. Li M, Zhai H, Huang Z, Liu X, Zhou Y, Li S, Li C. Microstructure and mechanical properties of TiC0.5 reinforced copper matrix composites, Materials Science & Engineering A, 2013;588:335-339. http://dx.doi.org/10.1016/j.msea.2013.09.054 Kang HK. Microstructure and electrical conductivity of high volume Al2 O3 reinforced copper matrix composites produced by plasma spray, Surf Coat Technology, 2005;190:448-452. http://dx.doi.org/10.1016/j.surfcoat.2004.02.002
  7. Zhu J, Liu L, Zhao H, Shen B, Hu W. Microstructure and Performance of Electroformed Cu/nano-SiC Composite, Materials Design, 2007;28:1958-1962. http://dx.doi.org/10.1016/j.matdes.2006.04.021
  8. Durisin J, Durisinova K, Orolınova M, Saksl K. Effect of the MgO particles on the nanocrystalline copper grain stability, Materials Letters 2004;58:3796-3801. http://dx.doi.org/10.1016/j.matlet.2004.07.031
  9. Lin YC, Li HC, Liou SS, Shie MT. Mechanism of plastic deformation of powder metallurgy metal matrix composites of Cu-Sn/SiC and 6061/SiC under compressive stress, Materials Science and Engineering A, 2004;373:363-369. http://dx.doi.org/10.1016/j.msea.2004.02.011