Dergiler / Research on Engineering Structures and Materials / 2019 / Cilt: 5 - Sayı: 4

Finite element evaluation of notch effect on partial penetration T-joints subjected to distinct toe-grinding processes

Sayfa
403–413
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

In a resume, this work indicates that a simple and adaptable for automated manufacturing procedure may provide similar fatigue performance of the relatively complex method preconized by standard codes.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Toe grinding process is widely employed for increasing fatigue life of welded structures with high dimensions, which are very usual in civil, naval and offshore industries.
📊
Temel Bulgular & Veri:In these cases, costs related to the application of an additional manufacturing process are naturally justified.
💡
Sonuç & Katkı:In a resume, this work indicates that a simple and adaptable for automated manufacturing procedure may provide similar fatigue performance of the relatively complex method preconized by standard codes.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

Toe grinding process is widely employed for increasing fatigue life of welded structures with high dimensions, which are very usual in civil, naval and offshore industries. In these cases, costs related to the application of an additional manufacturing process are naturally justified. However, code recommendations referred to toe grinding process are quite conservatives, which justifies investigations on the applicability of more effective and efficient procedures. This work presents an alternative toe grinding procedure for application in a partial penetration T-joint with fillets subjected to a longitudinal load. Such alternative was analyzed by comparison of results of Finite Element Analysis applied over modeled specimens corresponding to three cases: i) original configuration (no grinding process had been applied), ii) tip rib contouring groove (code based procedure) and iii) straight grinding groove. This last case was proposed because the manufacturing procedure is considerably simplified and easily adaptable for automated production. After performing the FE analysis, results indicated that notch effect is very similar for both grinding cases. This result supported the choice of the simplified grinding process for manufacturing a set of real specimens, assigned for fatigue testing. In a resume, this work indicates that a simple and adaptable for automated manufacturing procedure may provide similar fatigue performance of the relatively complex method preconized by standard codes.

🔖

Bu Makaleye Atıf Yap

FUNES, G., AMARO, P., TEIXEIRA, P., BIANCHI, K. (2019). Finite element evaluation of notch effect on partial penetration T-joints subjected to distinct toe-grinding processes. Research on Engineering Structures and Materials, Cilt: 5 - Sayı: 4, 403–413. https://ajindex.com/articles/302610

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. Moehring HC, Brecher C, Abele E, Fleischer J, Bleicher F. Materials in machine tool structures. CIRP Annals, 2015; 64(2): 725-748.
  2. Odot - Ohaio Department of Transportation. On-line Bridge Maintenance Manual Preventive Maintenance/Repair. Guidelines for Bridges and Culverts 2008. Available in: https://www.dot.state.oh.us/Divisions/Engineering/Structures/bridge%20operation s%20and%20maintenance/PreventiveMaintenanceManual/BPMM/beams/sbeams.h tm [3] Roy J, Munro B, Walley S, Meredith A. Longitudinal versus Transversely Framed Structures for Large Displacement Motor Yachts. In 20th International HISWA Symposium on Yacht Design and Yacht Construction, Amsterdam, The Netherlands, 2008
  3. Branco CM, Fernandes AA, Castro PMST. Fadiga de Estruturas Soldadas, Fundação Calouste Gulbenkian, Lisboa, PT, 1999
  4. Blondeau R. Metallurgy and Mechanics of Welding, Processes and Industrial Applications. John Wiley & Sons Inc, Hoboken, NJ, USA, 2008
  5. Lassen T, Récho N. Fatigue Life Analyses of Welded Structures: Flaws, ISTE, Londres, ENG, 2006.
  6. Suresh S. Fatigue of materials, Cambridge university press, Cambridge, ENG, 1998
  7. Hicks J. Welded joint design, Industrial Press, New York, NY, USA, 1999
  8. Maddox SJ. Fatigue Strength of Welded Structures. 2nd Ed. Woodhead Publishing Ltd and The Welding Institute. Cambridge, 2002
  9. Kirkhope KJ, Bell R, Caron L, Basu R I, Ma K-T. Weld detail fatigue life improvement techniques. Part 2: application to ship structures. Marine Structures, 1999; 12: 477- 496.
  10. Haagensen PJ, Maddox SJ. Recommendations on Post Weld Improvement of Steel and Aluminium Structures. IIW Doc, 2006; 13: 1815-00
  11. Funes GX. Evaluation of a modified version of the toe grinding technique in the fatigue life improvement for longitudinally loaded T joints made AISI 316 L stainless steel. Msc. Dissertation, Federal University of Rio Grande – FURG, Rio Grande, 2017
  12. Silva MSda. Comparison of fatigue life of microlight structural steel joints welded by Gas Metal Arc Welding - GMAW and Flux Cored Arc Welding - FCAW. Msc. Dissertation, Federal University of Rio Grande – FURG, Rio Grande, 2018
  13. Eurocode 3. Design of steel structures – Part 1.9: Fatigue, CEN, Brussels, BEL, 2003 [15] American Welding Society. AWS D1.1/D1.1M:2010: Structural Welding Code – Steel. Miami, 2010. [16]Hobbacher A. Recommendati