Dergiler / Research on Engineering Structures and Materials / 2021 / Cilt: 7 - Sayı: 1

Impact of multi-walled carbon nanotube and graphene oxide on abrasive wear performance of polypropylene

Sayfa
157–171
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The minimized coefficient of friction and wear volume was obtained at 0.3%wt GO filled PP nanocomposite with the parameters of 100m sliding speed and 1200 grid emery paper number with a value of 0.2716 and 3.07 mm3, respectively.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, the abrasive wear behavior of multi-walled carbon nanotube (MWCNT) and graphene oxide (GO) filled polypropylene (PP) nanocomposites without using compatibiliser were investigated.
📊
Temel Bulgular & Veri:The tribological tests were performed in dry condition using pin-on-disc at 1.0m/s sliding speed and 10N load.
💡
Sonuç & Katkı:The minimized coefficient of friction and wear volume was obtained at 0.3%wt GO filled PP nanocomposite with the parameters of 100m sliding speed and 1200 grid emery paper number with a value of 0.2716 and 3.07 mm3, respectively.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

In this study, the abrasive wear behavior of multi-walled carbon nanotube (MWCNT) and graphene oxide (GO) filled polypropylene (PP) nanocomposites without using compatibiliser were investigated. The effects of material type, sliding distance, and emery paper number on the abrasive wear of PP nanocomposites were investigated by adopting a statistical approach. The tribological tests were performed in dry condition using pin-on-disc at 1.0m/s sliding speed and 10N load. The optimization of signal-to-noise ratio (S/N) and degree of significance of the control variables to minimize the wear volume and coefficient of friction was carried out. As a result of the study, wear volume and coefficient of friction increased with increasing sliding distance, while decreased with increasing emery paper number for all tested materials. The coefficient of friction of the MWCNT and GO filled PP nanocomposites decreased by 19% and 23% compared to unfilled PP polymer, respectively. GO filled PP nanocomposites was found to be approximately 95% less wear volume than MWCNT filled PP nanocomposites. The minimized coefficient of friction and wear volume was obtained at 0.3%wt GO filled PP nanocomposite with the parameters of 100m sliding speed and 1200 grid emery paper number with a value of 0.2716 and 3.07 mm3, respectively.

🔖

Bu Makaleye Atıf Yap

YETGİN, S. H. (2021). Impact of multi-walled carbon nanotube and graphene oxide on abrasive wear performance of polypropylene. Research on Engineering Structures and Materials, Cilt: 7 - Sayı: 1, 157–171. https://ajindex.com/articles/302588

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (10)

  1. Mertens AJ, Senthilvelan S. Mechanical and tribological properties of carbon nanotube reinforced polypropylene composites. Journal of Materials: Design and Applications. 2018;232(8):669-680.
  2. Ravi Kumar BN, Suresh B, Venkataramareddy M. Effect of Abrasives on Three-Body Abrasive Wear Behaviour of Particulate-Filled Polyamide66/Polypropylene Nanocomposites. Composite Interfaces. 2010;17:113-126.
  3. Yuanshi X, Fanglin X, Mingming W, Tongsheng L. Synergistic Effects of Carbon Nanotube/Nano‑MoS2 Hybrid on Tribological Performance of Polyimide Nanocomposite Films. Tribology Letters. 2018; 66(25):1-18.
  4. Hassan A. El-Sayed M, EiD A.I, El-Sheikh M, Ali WY. Trıbologıcal propertıes of Low Densıty Polyethylene and Polyamıde 12 as polymer matrıx nanocomposıtes, Journal of the Egyptıan Socıety of Trıbology. 2017;14(4):40-53
  5. Yuanshi X, Tongsheng L, Dafei G, Fanglin X, Mingming W. Preparation and tribological properties of graphene oxide/nano-MoS2 hybrid as multidimensional assembly used in the polyimide nanocomposites. RSC Advances. 2017;7:6323-6335.
  6. Beibei C, Xiang L, Yuhan J, Lin X, Hongyu L, Xiaofang L, Jin Y, Changsheng L, Fengyuan Y. Fabrication of ternary hybrid of carbon nanotubes/graphene oxide/MoS2 and its enhancement on the tribological properties of epoxy composite coatings. Composites Part A. 2018;115:157-165.
  7. Barretta R, Ali Faghidian S, Marotti de Sciarra F, Pinnola F. P. Timoshenko nonlocal strain gradient nanobeams: Variational consistency, exact solutions and carbon nanotube Young moduli. Mechanics of Advanced Materials and Structures.2019;1-15.
  8. Shim YS, Park SJ. Influence of glycidyl methacrylate grafted multiwalled carbon nanotubes on viscoelastic behaviors of polypropylene nanocomposites. Carbon Letters. 2010;11:311-315.
  9. Golchin AAW, Nazanın E. An investigation into tribological behaviour of multi-walled carbon nanotube/graphene oxide reinforced UHMWPE in water lubricated contacts. Tribology International. 2016;95:156-161.
  10. Liu Y, Qıhua W, Tıngmeı W, Guangqın P. Preparation and tribological properties of graphene oxide/nitrile rubber nanocomposites. Journal of Materials Science.2