KaydedilenlerDerginizi ekleyin

Dergiler / International Journal of Advances in Engineering and Pure Sciences / 2019 / Özel Sayı I:

Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD)

Oğuz ERDEM
Can ÇOĞUN
İbrahim USLAN
Sayfa
11–16
Yayın Tarihi
2019-05-20
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The conducted experiments revealed the strong dependence of surface characteristics on machining parameters.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In electric discharge drilling (EDD), rapid local heating and cooling of the workpiece surface by means of electric discharges results in surface layers (recast, heat affected and base material).
📊
Temel Bulgular & Veri:In this study, the main workpiece surface texture measures, namely the recast layer thickness (RLT) and average surface roughness (Ra) characteristics were investigated for varying machining parameters (discharge current and pulse on time).
💡
Sonuç & Katkı:The conducted experiments revealed the strong dependence of surface characteristics on machining parameters.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Electric discharge drilling · Recast layer thickness · Average surface roughness

Özet

In electric discharge drilling (EDD), rapid local heating and cooling of the workpiece surface by means of electric discharges results in surface layers (recast, heat affected and base material). In this study, the main workpiece surface texture measures, namely the recast layer thickness (RLT) and average surface roughness (Ra) characteristics were investigated for varying machining parameters (discharge current and pulse on time). The conducted experiments revealed the strong dependence of surface characteristics on machining parameters.

Abstract

In electric discharge drilling (EDD), rapid local heating and cooling of the workpiece surface by means of electric discharges results in surface layers (recast, heat affected and base material). In this study, the main workpiece surface texture measures, namely the recast layer thickness (RLT) and average surface roughness (Ra) characteristics were investigated for varying machining parameters (discharge current and pulse on time). The conducted experiments revealed the strong dependence of surface characteristics on machining parameters.

🔖

Bu Makaleye Atıf Yap

ERDEM, O., ÇOĞUN, C., USLAN, İ. (2019). Effect of Machining on Workpiece Surface Characteristics in Electric Discharge Drilling (EDD). International Journal of Advances in Engineering and Pure Sciences, Özel Sayı I:, 11–16. https://ajindex.com/articles/257777

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

  1. Gülcan, O., Uslan, İ., Usta, Y., & Çoğun, C. (2015). Elektro Erozyon ile İşlemede Cu-Cr T/M Elektrot Kullanımının İşleme Performansına Etkisi. Journal of the Faculty of Engineering and Architecture of Gazi University, 30(3), 381-394
  2. Erdem, O., Çoğun, C., Urtekin, L., Özerkan, H. B., & Uslan, İ. (2016). Toz katkılı ve ısıtılmış dielektriğin elektro erozyon ile işlemede (EEİ) delik delme performansı üzerine etkisi. Journal of the Faculty of Engineering and Architecture of Gazi University, 31(3), 531-544
  3. Li, J., Shi, S., & Zhao, S. (2013). Modeling and Analysis of Micro-hole in Die-sinking EDM Process through Response Surface Method based on the Central Composite Design. International Journal of Signal Processing, Image Processing and Pattern Recognition, 6(6), 351-364
  4. Yılmaz, O., Bozdana, A. T., & Okka, M. A. (2014). An intelligent and automated system for electrical discharge drilling of aerospace alloys: Inconel 718 and Ti-6Al-4V. Int. J. Adv. Manuf. Technol, 74(9), 1323-1336
  5. Bozdana, A. T., & Al-Karkhi, N. K. (2017). Comparative experimental investigation and gap flow simulation in electrical discharge drilling using new electrode geometry. Mechanical Sciences, 8(2), 289–298
  6. D'Urso, G., Maccarini, G., Quarto, M., Ravasio, C., & Caldara, M. (2016). Micro-electro discharge machining drilling of stainless steel with copper electrode: The influence of process parameters and electrode size. Advances in Mechanical Engineering, 8(12), 1-16
  7. Unses, E., & Cogun, C. (2015). Improvement of Electric Discharge Machining (EDM) Performance of Ti-6Al-4V Alloy with Added Graphite Powder to Dielectric. Strojniški vestnik - Journal of Mechanical Engineering, 61(6), 409-418
  8. Newton, T. R., Melkote, S. N., Watkins, T. R., Trejo, R. M., & Reister, L. (2009). Investigation of the effect of process parameters on the formation and characteristics of recast layer in wire-EDM of Inconel 718. Materials Science and Engineering A - Structrual Materials Properties, 5(4), 208-215
  9. Chen, S. L., Lin, M. H., Huang, G. X., & Wang, C. C. (2014). Research of the recast layer on implant surface modified by micro-current electrical discharge machining using deionized water mixed with titanium powder as dielectric solvent. Applied Surface Science, 31(1), 47-53
  10. Shabgard, M. R., Seyedzavvar, M., & Oliaei, S. (2011). Influence of input parameters on characteristics of EDM process. Strojni˘ ski vestnik - J. Mech. Eng., 57(9), 689-696
  11. Arooj, S., Sh