KaydedilenlerDerginizi ekleyin

Dergiler / Gazi University Journal of Science / 2014 / Cilt: 27 - Sayı: 2

The Effects of Coating Obtained by DC Reactive Magnetron Sputtering Technique on the Wear Performance of Engine Parts

Oğuzhan BENDEŞ
Şengül DANIŞMAN
Sayfa
871–881
Yayın Tarihi
2014-06-27
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

It was found that the hardened + nitrided of AISI 4150 samples with high nitrogen pressure (1.2 mtorr) gave the best wear resistance which resulted in a decreased coefficient of friction and a reduction in wear rates

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, TiAlN coating obtained by using the magnetron sputtering method was deposited on steel materials used in automotive engine parts.
📊
Temel Bulgular & Veri:TiAlN coatings were deposited on base materials (AISI 4150) using selected parameters ( 0,-100V and-200V bias voltages and 0.3 mtorr, 0.6 mtorr, 1.2 mtorr pressures).
💡
Sonuç & Katkı:It was found that the hardened + nitrided of AISI 4150 samples with high nitrogen pressure (1.2 mtorr) gave the best wear resistance which resulted in a decreased coefficient of friction and a reduction in wear rates
🔬Tür:Araştırma Makalesi
📍Kapsam:4150 samples
⚙️Değişkenler:Magnetron sputtering method · TiAlN · Engine Parts

Abstract

In this study, TiAlN coating obtained by using the magnetron sputtering method was deposited on steel materials used in automotive engine parts. The characterization and wearing properties of the coatings were investigated. The distance between the target and the coating was kept constant during the operation. TiAlN coatings were deposited on base materials (AISI 4150) using selected parameters ( 0,-100V and-200V bias voltages and 0.3 mtorr, 0.6 mtorr, 1.2 mtorr pressures). Hardening and nitriding processes were applied to the base materials. The coating characteristics of hardened and hardened + nitrided samples, surface properties and wear behavior were compared. The best results for the coating characteristics were determined. It was found that the hardened + nitrided of AISI 4150 samples with high nitrogen pressure (1.2 mtorr) gave the best wear resistance which resulted in a decreased coefficient of friction and a reduction in wear rates

🔖

Bu Makaleye Atıf Yap

BENDEŞ, O., DANIŞMAN, Ş. (2014). The Effects of Coating Obtained by DC Reactive Magnetron Sputtering Technique on the Wear Performance of Engine Parts. Gazi University Journal of Science, Cilt: 27 - Sayı: 2, 871–881. https://ajindex.com/articles/254844

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (6)

  1. Danışman Ş., Savaş S., Işık G., Bendeş O., Özbekler A., “Uçak Türbin Kanatlarında Kullanılan Erozyon ve Korozyon HASEM’08, Kayseri VIII. Havacılık Sempozyumu, Erciyes Üniv., Kayseri, 41-47, (2008). Kaplamalar”, [2] Vetter J., Barbezat G., Crummenauer J., Avissar J., “Surface Applications”, Surface and Coating Technology, 200, 1962-1968, (2005). for Automotive [3] Ceschini L., Lanzoni E., Martini C., Prandstraller D. and Sambogna G., “Comparison of Dry Sliding Friction and Wear of Ti6Al4V Alloy Treated by Plasma Electrolytic Oxidation and PVD Coating”, Wear, Vol. 264, pp. 86-95, (2008).
  2. Gahlin R., Larsson M., Hedenqvist P.,”ME-C:H coatings in motor vehicles”, Wear, 249,302-309,(2001)
  3. Zhuo S., Peijun Z., Leheng Z., Xinfu X., Aimin H., Wenquan Z., “Muti-Layer Compound Coating on Cast Iron Piston Ring by Multi-Arc and Magnetron Sputtering Ion-Compound Coatings Technology, 131, 422-427, (2000). Technique”, Surface and Agarwal K.A.,Garg A., Srivastava D.K., Shukla M. K., “Comparative wear performance of titanium based coatings for automotive applications using exhaust gas recirculation”, Surface and Coatings Techn., 201,6182- 6188,(2007). Mezlini S., et al., “Effect of Indenter Geometry and Relationship Between Abrasive Wear and Hardness in Early Stage of Repetitive Sliding”, Wear, 260, 412-421, (2006). Efeoğlu I., “Co-sputtered Mo:S:C:Ti:B Based Coating for Tribological Applications”, Surface and Coatings Technology, 200, 1724-1730, (2005).
  4. Lau K.H., Li K.Y., “Correlation between Adhesion and Wear Behaviour of Commercial Carbon Based Coatings”, Tribology International, 39, 115-123, (2006). [10] Wuhrer R., Yeung W.Y., “Effect of Target-Substrate Working Distance on Magnetron Sputter Deposition of Nanostructured Titanium Aluminium Nitride Coatings”, Scripta Materialia, 49, 199-205, (2003).
  5. Wuhrer R., Kim S., Yeung W.Y., “Effect of Nitrogen Partial Pressure on the Surface Morphology and Properties of Reactive DC Magnetron Sputtered Titanium Aluminium Nitride Coatings”, Scripta Materialia, 37, 1163-1168, (1997).
  6. Tanaka Y., Gür T.M., Kelly M., Hagstrom S.B., Ikeda T., “Structure and properties of (Ti1−xAlx)N films prepared by reactive sputtering” Thin Solid Films, 228, 1–2, 238-241, (1993). Håkansson G., Sundgren J.E., McIntyre D., Greene J.E., Münz W.D., “Microstructure and physical properties of polycrystalline metastable Ti0.5Al0.5N alloys grown by d.c. magnetron sputter deposition”, Thin Solid Films, 153, 1–3, 55-65, (1987). Barshilia H.C.,Yogesh K.,Rajam K.S.