KaydedilenlerDerginizi ekleyin

Dergiler / Gazi University Journal of Science / 2018 / Cilt: 31 - Sayı: 1

Design and Development of the I.T.U. Biped Robot

Zeki Yağız BAYRAKTAROĞLU
Mesut ACAR
Alper GERÇEK
Numan Mert TAN
Sayfa
251–271
Yayın Tarihi
2018-03-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The robot’s mass without batteries is 55 kg and its height is 142 cm.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:This paper presents the design and construction of a 12-DoF biped walking robot.
📊
Temel Bulgular & Veri:The kinematics of electrically actuated 6-DoF legs is similar to that of human legs with three DoF at the hip, one at the knee and two at the ankle joints.
💡
Sonuç & Katkı:The robot’s mass without batteries is 55 kg and its height is 142 cm.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Biped robot · Dynamical simulation · Design

Abstract

This paper presents the design and construction of a 12-DoF biped walking robot. The kinematics of electrically actuated 6-DoF legs is similar to that of human legs with three DoF at the hip, one at the knee and two at the ankle joints. The mechanical design of the robot was based on dynamical simulations realized in a modular PC environment. Two communicating software were used in order to solve the forward dynamics of the system and to design walking controllers. Forward, backward and lateral walking as well as stair climbing behaviors with up to 6 km/h forward walking speeds have been simulated in order to determine the nominal power rates required at joints. Hip joints are actuated by DC motors coupled to harmonic reducers situated both in joint axes. The actuators driving the knee and ankle joints are situated higher than the respective joint axes and the rotational output motion of DC motors are transmitted to the joints through linear ball-screw mechanisms. Spherical joints are used within the transmission of spatial motion required for the 2-DoF at ankle joints. All joints consist of absolute encoders and 6-axes force/torque transducers are mounted at the ankle joints. The robot is controlled through an embedded industrial PC running real-time operating system. All electronic control hardware including the motor drivers and sensors communicate through CAN bus. The robot’s mass without batteries is 55 kg and its height is 142 cm.

🔖

Bu Makaleye Atıf Yap

BAYRAKTAROĞLU, Z. Y., ACAR, M., GERÇEK, A., TAN, N. M. (2018). Design and Development of the I.T.U. Biped Robot. Gazi University Journal of Science, Cilt: 31 - Sayı: 1, 251–271. https://ajindex.com/articles/254689

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (12)

  1. Hirai, K., “Current and Future Perspective of Honda Humanoid Robot”, Proceedings of the IEEE/RSJ International Conference on Intelligent Robots, Grenoble, France, 2: 500–508, (1997)
  2. Hirai, K., Hirose, M., Haikawa, Y., Takenaka, T., “The Development of Honda Humanoid Robot”, Proceedings of the IEEE International Conference on Robotics and Automation, Leuven, Belgium, 2: 1321–1326, (1998)
  3. Sakagami, Y., Watanabe, R., Aoyama, C., Matsunaga, S., Higaki, N., Fujimura, K., “The intelligent ASIMO: System overwiew and integration”, Proceedings of the IEEE/RSJ International Conference on Intelligent Robots, Lausanne, Switzerland, 3: 2478–2483, (2002)
  4. Inoue, H., Tachi, S., Nakamura, Y., Hiari, K., “Overview of Humanoid Robotics Project of METI”, Proceedings of the International Symposium on Robotics, Seoul, Korea, 1478–1482, (2001)
  5. Kaneko, K., Kanehiro, F., Kajita, S., Yokoyama, K., Akachi, K., Kawasaki, T., Ota, S., Isozumi, T., “Design of Prototype Humanoid Robotics Platform for HRP”, Proceedings of the IEEE/RSJ International Conference on Intelligent Robots, Lausanne, Switzerland, 3: 2431–2436, (2002)
  6. Hirukawa, H., Kanehiro, F., Kaneko, K., Kajita, S., “Humanoid Robotics Platforms Developed in HRP”, Robotics and Autonomous Systems, 48(4): 165–175, (2004)
  7. Akachi, K., Kaneko, K., Kanehira, N., Ota, S., Miyamori, G., Hirata, M., Kajita, S., Kanehiro, F., “Development of Humanoid Robot HRP-3P”, Proceedings of the IEEE RAS International Conference on Humanoid Robots, Tsukuba, Japan, 50–55, (2005)
  8. Takanishi, A., Ishida, M., Yamazaki, Y., Kato, I., “The realization of dynamic walking by the biped walking robot WL-10RD”, Proceedings of the International Conference on Advanced Robotics, 459–466, (1985)
  9. Lim, H., Takanishi, A., “Biped walking robots created at Waseda University: WL and WABIAN family”, Phil. Transactions of the Royal Society A, 365: 49–64, (2007)
  10. Park, I.W., Kim, J.Y., Lee, J., Oh, J.H., “Mechanical design of humanoid robot platform KHR-3”, Proceedings of the IEEE RAS International Conference on Humanoid Robots, Tsukuba, Japan, 321–326, (2005)
  11. Pfeiffer, F., Löffler, K., Gienger, M., “The Concept of Jogging JOHNNIE”, Proceedings of the IEEE International Conference on Robotics and Automation, Washington D.C., USA, 3129–3135, (2002)
  12. Löffler, K., Gienger, M., Pfeiffer, F., “Sensor and Control Design of a Dynamically Stable Biped Robot”, Proceedings of the IEEE International Conference on Robotics and