KaydedilenlerDerginizi ekleyin

Dergiler / Gazi University Journal of Science / 2017 / Cilt: 30 - Sayı: 2

OPTIMIZATION OF MQL PARAMETERS USING THE TAGUCHI METHOD IN MILLING OF WASPALOY

Çağrı Vakkas YILDIRIM
Turgay KIVAK
Fehmi ERZİNCANLI
İlyas UYGUR
Murat SARIKAYA
Sayfa
173–186
Yayın Tarihi
2017-06-19
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

In addition, confirmation test results showed that the Taguchi method was very successful in the optimization of MQL parameters in order to obtain minimum surface roughness in milling of Waspaloy super alloy.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:This study aimed to investigate the effect of the minimum quantity lubrication (MQL) parameters such as cutting oil type, flow rate, milling method, pulverization distance and nozzle type on average roughness (Ra) in milling of nickel based Waspaloy super alloy.
📊
Temel Bulgular & Veri:During milling experiments, constant cutting speed (45 m/min), constant feed rate (0.1 mm/rev) and constant depth of cut (0.5 mm) selected were as machining parameters.
💡
Sonuç & Katkı:In addition, confirmation test results showed that the Taguchi method was very successful in the optimization of MQL parameters in order to obtain minimum surface roughness in milling of Waspaloy super alloy.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Waspaloy · Milling · MQL

Abstract

This study aimed to investigate the effect of the minimum quantity lubrication (MQL) parameters such as cutting oil type, flow rate, milling method, pulverization distance and nozzle type on average roughness (Ra) in milling of nickel based Waspaloy super alloy. During milling experiments, constant cutting speed (45 m/min), constant feed rate (0.1 mm/rev) and constant depth of cut (0.5 mm) selected were as machining parameters. Four different types of oil (vegetable, synthetic, mineral and mineral-synthetic), four different flow rates (25, 50, 75 and 100 ml/h), two different milling methods (down milling and up milling) two pulverization distances (25 and 50 mm) and two different nozzle types were selected as MQL parameters. The results were analyzed using 3D surface graphs, signal-to-noise ratio (S/N) and main effect graphs of means. Optimal operating parameters were determined using the S/N ratio and desirability function analysis. Mathematical models have been created for surface roughness. The analysis results indicated that the feed rate was the dominant factors oil type and flow ratio on surface roughness. In addition, confirmation test results showed that the Taguchi method was very successful in the optimization of MQL parameters in order to obtain minimum surface roughness in milling of Waspaloy super alloy.

🔖

Bu Makaleye Atıf Yap

YILDIRIM, Ç. V., KIVAK, T., ERZİNCANLI, F., UYGUR, İ., SARIKAYA, M. (2017). OPTIMIZATION OF MQL PARAMETERS USING THE TAGUCHI METHOD IN MILLING OF WASPALOY. Gazi University Journal of Science, Cilt: 30 - Sayı: 2, 173–186. https://ajindex.com/articles/254616

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (14)

  1. Chouldhury, I. A., “Machinability studies of high strength materials and the development of a data base system”, PhD thesis, Dublin City University, (1995).
  2. Caruso, S., Imbrogno, S., Rinaldi S. and Umbrello, D., “Finite element modeling of microstructal changes in waspaloy dry Machining”, The International Journal of Advanced Manufacturing Technology, (2016).
  3. Kulawinski, D, Henkel, S, Biermann, H, Holländer, D., Thiele, M., Gampe, U., “Isotermal and thermo-mechanical fatigue beyavior of the nickel base superalloy Waspaloy under unaxial and biaxial-planar loading”, International Journal of Fatigue, Volume 81, 21-36, (2015).
  4. Chamanfar, A., Jahazi, M., Gholipour, J., Wanjara, P., Yue, S., “Analysis of integrity and microstructure of linear friction welded Waspaloy”, Materials Characterization, Volume 104, 149-161, (2015).
  5. Uzun G., Turgut, Y., “The İnvestigation of The Cutting Parameters on Apllied Filled Welds on DIN 1.2344 and DIN 1.2379 Tool Steels in Milling”, 4th International Conference on Welding Technologies and Exhibition (ICWET’16), 11-13
  6. May, Gaziantep-TURKEY, (2016).
  7. Yıldırım, Ç.V., Kivak, T., Sarikaya, M., Mert, Ş., “Investigation of The Effect on Surface Roughness of The Minimum Quantity Lubrication (MQL) Parameters in Turning of AISI 4340”, 7th International Symposium on Machining, 3-5
  8. November, İstanbul, (2016).
  9. Lawal, S. A., Choudhury, I. A., Nukman, Y., “Application of vegetable oil-based metalworking fluids in machining ferrous metals; A Review”, Int. J. Mach. Tool. Manu. 52 (1), 1-12, (2012).
  10. Razak, N. H., Rahman, M. M., Noor, M.M., Kadirgama K., “A Revıew Of Mınımum Quantıty Lubrıcant On Machınıng Performance”, National Conference in Mechanical Engineering Research and Postgraduate Students, FKM Conference Hall, UMP, Kuantan, Pahang, Malaysia; pp. 72 -85, (2010).
  11. Jurko, J., Panda, A., “Application of vegetable oil-based metalworking fluids in machining ferrous metals-A review,” International Journal of Machine Tools and Manufacture, vol. 52, no. 1, pp. 1 12, (2012).
  12. Yıldırım, Ç. V., Kıvak, T., Erzincanlı, F., “A Rewiew on Application of Milling and Turning Processes of Minimum Quantity Lubrication System”, 2. International Iron and Steels Symposium, Karabük, Türkey, (2015).
  13. Sharma, V. S., Manu, D., Suri, N. M., “Cooling techniques for improved productivity in turning”, Int. J. Mach. Tool. Manu., 49 (6), 435-453, (2009).
  14. Dilipak. H., Guldas, A., Gezgin, A., “An Investigation of the Number of Inserts Effect on the Machining Time and Metal