Withdrawal force capacity of mortise and loose tenon T-type furniture joints

Amaç & Hipotez:The main goal of this study was to determine the effect of wood species and loose tenon length on the withdrawal force capacity of mortise and loose tenon (M&LT) T-type furniture joints.

📊

Temel Bulgular & Veri:The lengths in the present study were 10, 20, and 30 mm.

💡

Sonuç & Katkı:The greatest withdrawal force capacity increment of M&LT T-type joints was obtained when the tenon length changed from 10 to 20 mm.

🔬Tür:Araştırma Makalesi

📍Kapsam:Genişletilmiş Akademik Örneklem

⚙️Değişkenler:Key words: Furniture · loose tenon · tenon length

Özet

The main goal of this study was to determine the effect of wood species and loose tenon length on the withdrawal force capacity of mortise and loose tenon (M&LT) T-type furniture joints. The specimens were manufactured from oak (Quercus alba), beech (Fagus orientalis L.), poplar (Populus deltoides), sycamore (Platanus orientalis), fir (Abies alba), and white walnut (Juglans cinerea), and the tenon species selected was oriental beech (Fagus orientalis L.). The length of the tenon was determined on the basis of the length glued into the horizontal member of the joint. The lengths in the present study were 10, 20, and 30 mm. It was found that joints manufactured from beech had the highest withdrawal force capacity; this trait was lowest in joints made from the light wood of poplar and fir. The glued-in length of the tenon exerted a significant influence on the withdrawal force capacity of the joints. The greatest withdrawal force capacity increment of M&LT T-type joints was obtained when the tenon length changed from 10 to 20 mm.

Abstract

The main goal of this study was to determine the effect of wood species and loose tenon length on the withdrawal force capacity of mortise and loose tenon (M&LT) T-type furniture joints. The specimens were manufactured from oak (Quercus alba), beech (Fagus orientalis L.), poplar (Populus deltoides), sycamore (Platanus orientalis), fir (Abies alba), and white walnut (Juglans cinerea), and the tenon species selected was oriental beech (Fagus orientalis L.). The length of the tenon was determined on the basis of the length glued into the horizontal member of the joint. The lengths in the present study were 10, 20, and 30 mm. It was found that joints manufactured from beech had the highest withdrawal force capacity; this trait was lowest in joints made from the light wood of poplar and fir. The glued-in length of the tenon exerted a significant influence on the withdrawal force capacity of the joints. The greatest withdrawal force capacity increment of M&LT T-type joints was obtained when the tenon length changed from 10 to 20 mm.

Anahtar kelimeler

Key words: Furniture loose tenon tenon length withdrawal force capacity wood species

🔖

Bu Makaleye Atıf Yap

DERIKVAND, M., SMARDZEWSKI, J., EBRAHIMI, G., DALVAND, M., MALEKI, S. (2013). Withdrawal force capacity of mortise and loose tenon T-type furniture joints. Turkish Journal of Agriculture and Forestry, Cilt: 37 - Sayı: 3, 377–384. https://ajindex.com/articles/180075

📄 Tam Metin PDF Okuyucu

Yeni Sekmede Aç ↗

↗Yeni Sekme

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

Akcay H, Eckelman CA, Haviarova E (2005) Withdrawal, shear, and bending moment capacities of round mortise and tenon timber framing joints. For Prod J 55: 60–72.
Altinok M, Taş HH, Sancak E (2009) Load carrying capacity of spline joints as affected by board and adhesives type. Sci Res Essay 4: 479–473.
Aman RL, West HA, Cormier DR (2008) An evaluation of loose tenon joint strength. For Prod J 58: 61–64. American Society of Testing and Materials (1999a) ASTM D-143. Standard Test Methods for Small Clear Specimens of Timber. American Society of Testing and Materials, West Conshohocken, PA, USA. American Society of Testing and Materials (1999b) ASTM D-2395. Standard Test Methods for Specific Gravity of Wood and Wood-Based Materials. American Society of Testing and Materials, West Conshohocken, PA, USA. Eckelman CA (2003) Textbook of Product Engineering and Strength Design of Furniture. Purdue University Press,
West Lafayette, IN, USA. Eckelman CA, Erdil Y, Haviarova E (2006a) Effect of shoulders on bending moment capacity of round mortise and tenon joints. For Prod J 56: 82–86.
Eckelman CA, Erdil Y, Zhang J (2002) Withdrawal and bending strength of dowel joints constructed of plywood and oriented strand board. For Prod J 52: 66–74.
Eckelman CA, Haviarova E, Akcay H (2006b) Exploratory study of the withdrawal resistance of round mortise and tenon joints with steel pipe cross pins. For Prod J 56: 55–61.
Eckelman CA, Haviarova E, Erdil YZ, Akcay H, Tankut A, Denizli N (2004) Bending moment capacity of round mortise and tenon furniture joints. For Prod J 54: 192–197.
Haviarova E, Eckelman CA, Erdil YZ (2001a) Design and testing of wood school desk frames suitable for production by low technology methods from waste wood residues. For Prod J 51: 79– Haviarova E, Eckelman CA, Erdil YZ (2001b) Design and testing of environmentally friendly wood school chairs for developing countries. For Prod J 51: 58–64.
Maleki S, Derikvand M, Dalvand M, Ebrahimi GH (2012) Load carrying capacity of mitered furniture corner joints with dovetail keys under diagonal tension load. Turk J Agric For 36: 636–643. Martinović D, Horman I, Hajdarević S (2008) Stress distribution in wooden corner joints (Raspodjela naprezanja u drvenim kutnim spojevima). Strojarstvo 50: 193–204 (in Croatian). Smardzewski J (1998) Numerical analysis of furniture constructions. Wood Sci Technol 32: 273–286.
Smardzewski J (2002) Strength of profile-adhesive joints. Wood Sci Technol 36: 173–183.
Smardzewski J, Papu