Dergiler / Isı Bilimi ve Tekniği Dergisi / 2026 / Cilt: 46 Sayı: 2

Elektrik motorlarında stator halkası yüzeyine püskürtmeli soğutmanın geçici ısı transfer kapasitesinin sayısal simülasyonu

Numerical simulation of transient heat transfer capability of stator ring surface spray cooling in electric motors

Yuqi Qian(Xinghua People's Hospital Affiliated to Yangzhou University)0009-0006-1407-677X
Meng Zhang(university of sussex)0000-0002-2243-9730
Xinwen Chen(Yangzhou University)0000-0002-6138-631X
Sayfa
268–275
Yayın Tarihi
2026-10-30
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Simülasyon sonuçları, meme sayısının artmasının sıvı film kaplamasını artırdığını ve sıcaklık homojenliğini iyileştirdiğini göstermektedir.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Elektrikli araç motorlarının sürekli artan güç yoğunluğundan kaynaklanan ve geleneksel soğutma teknolojilerinin başa çıkmakta zorlandığı aşırı ısınma sorununu ele almak için, bu çalışma motor statorunun halka şeklindeki yüzeyinde geçici bir ısı transferi sayısal modeli geliştirmiştir.
📊
Temel Bulgular & Veri:Meme sayısı, püskürtme akış hızı (Q) ve meme yüksekliğinin stator yüzeyinin ısı transfer kapasitesi üzerindeki etkileri araştırılmıştır.
💡
Sonuç & Katkı:Simülasyon sonuçları, meme sayısının artmasının sıvı film kaplamasını artırdığını ve sıcaklık homojenliğini iyileştirdiğini göstermektedir.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Motor statoru · Püskürtmeli soğutma · Sayısal model

Özet

Elektrikli araç motorlarının sürekli artan güç yoğunluğundan kaynaklanan ve geleneksel soğutma teknolojilerinin başa çıkmakta zorlandığı aşırı ısınma sorununu ele almak için, bu çalışma motor statorunun halka şeklindeki yüzeyinde geçici bir ısı transferi sayısal modeli geliştirmiştir. Meme sayısı, püskürtme akış hızı (Q) ve meme yüksekliğinin stator yüzeyinin ısı transfer kapasitesi üzerindeki etkileri araştırılmıştır. Simülasyon sonuçları, meme sayısının artmasının sıvı film kaplamasını artırdığını ve sıcaklık homojenliğini iyileştirdiğini göstermektedir. Ek olarak, Q'nun artması damlacık çarpma kinetik enerjisini artırır, sıvı film kalınlığını azaltır ve böylece maksimum yüzey sıcaklığını ve sıcaklık farkını düşürür. Dahası, meme yüksekliğinin artması daha homojen damlacık dağılımı sağlamaya, sıçramayı bastırmaya ve soğutma kapasitesini daha da iyileştirmeye yardımcı olur. 4000 Hz'lik bir titreşim frekansında, nozul sayısının 12'den 18'e, Q değerinin 4000 mL/dak'dan 8000 mL/dak'ya ve nozul yüksekliğinin 20 mm'den 30 mm'ye çıkarılması, maksimum sıcaklıkta sırasıyla 25,3 °C, 38,8 °C ve 13,1 °C'lik bir düşüşe neden olmaktadır.

Abstract

To address the overheating issue caused by the continuous increase in power density of electric vehicle motors, which traditional cooling technologies struggle to handle, this study develops a transient heat transfer numerical model on the annular surface of the motor stator. The effects of nozzle number, spray flow rate (Q), and nozzle height on the heat transfer capability of the stator surface are investigated. The simulation results show that increasing the number of nozzles enhances the liquid film coverage and improves temperature uniformity. Additionally, increasing the Q enhances the droplet impact kinetic energy, reduces the liquid film thickness, and thus lowers the maximum surface temperature and temperature difference. Furthermore, increasing the nozzle height helps achieve more uniform droplet distribution, suppresses splashing, and further improves cooling capability. Under a vibration frequency of 4000 Hz, increasing the nozzle number from 12 to 18, the Q from 4000 mL/min to 8000 mL/min, and the nozzle height from 20 mm to 30 mm results in a decrease in the maximum temperature by 25.3 °C, 38.8 °C, and 13.1 °C, respectively.

🔖

Bu Makaleye Atıf Yap

Qian, Y., Zhang, M., Chen, X. (2026). Elektrik motorlarında stator halkası yüzeyine püskürtmeli soğutmanın geçici ısı transfer kapasitesinin sayısal simülasyonu. Isı Bilimi ve Tekniği Dergisi, Cilt: 46 Sayı: 2, 268–275. https://doi.org/10.47480/isibted.1954978

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (35)

  1. Alaei, A., Hasanzadeh Kafshgari, M., & Atashi, H. (2012). A new designed heat pipe: an experimental study of the thermal performance in the presence of low-frequency vibrations. Heat and Mass Transfer, 48(4), 719-723. https://doi.org/10.1007/s00231-011-0908-3
  2. Atashi, H., Alaei, A., Kafshgari, M. H., Aeinehvand, R., & Rahimi, S. K. (2014). New pool boiling heat transfer in the presence of low-frequency vibrations into a vertical cylindrical heat source. Experimental Heat Transfer, 27(5), 428437. https://doi.org/10.1080/08916152.2013.797940
  3. Cebeci, I., Gürkan, S., Kırmacı, V., & Doğan, S. (2023). A new cooling approach to increase efficiency for the induction motor: Vortex tube. Heat Transfer Research, 54(15). https://doi.org/10.1615/HeatTransRes.2023048163
  4. Chang, M., Lai, B., Wang, H., Bai, J., & Mao, Z. (2023). Comprehensive efficiency analysis of air-cooled vs water-cooled electric motor for unmanned aerial vehicle. Applied Thermal Engineering, 225, 120226. https://doi.org/10.1016/j.applthermaleng.2023.120226
  5. Chauhan, V. K. S., & Koorata, P. K. (2024). Multidimensional investigation of thermal behavior of high-power electric vehicle motor during on-road driving conditions through electromagnetic, thermal, and drive cycle analysis. Computational Thermal Sciences: An International Journal, 16(5). 2024;16(5). https://doi.org/10.1615/ComputThermalScien.2024051735
  6. Chen, X., Du, A., Li, Z., Liang, K., Wang, X., Zhang, M., & Wang, Y. (2023). Heat transfer of single-phase spray cooling on heated vibrating surfaces. Case Studies in Thermal Engineering, 50, 103489. https://doi.org/10.1016/j.csite.2023.103489
  7. Chen, X., Du, A., Liang, K., Li, Z., Zhang, M., Yang, C., & Wang, X. (2024). Interaction between droplet impact and surface roughness considering the effect of vibration. International Journal of Heat and Mass Transfer, 220, 125018. https://doi.org/10.1016/j.ijheatmasstransfer.2023.125018
  8. Chen, X., Du, A., Wang, X., Yang, C., Liang, K., Li, Z.,. & Zhang, M. (2024). The effect of vibration on droplet dynamics and heat transfer of spray cooling. Applied Thermal Engineering, 238, 122074. https://doi.org/10.1016/j.applthermaleng.2023.122074
  9. Chen, X., Du, A., Zhang, M., Li, Z., Liang, K., & Qian, Y. (2025). The coupling effect of surface vibration and micro-structure on spray cooling heat transfer. International Journal of Heat and Mass Transfer, 236, 126409. https://doi.org/10.1016/j.ijheatmasstransfer.2024.126409
  10. Chen, X., Shen, Y., Li, Z., Qin, Y., Du, A., Zhou, Y.,. & Zhang, M. (2026). Numerical study of vibration effects on the transient boiling heat transfer of spray cooling. International Communications in Heat and Mass Transfer, 179,112305. https://doi.org/10.1016/j.icheatmasstransfer.2026.112305
  11. Chen, X., Zhou, Y., Shen, Y., Li, Z., Du, A., Zong, Z.,. & Qian, Z. (2026). Numerical study on the influence of spray parameters on liquid film dynamics and boiling rate under vibration conditions. Applied Thermal Engineering, 132211. https://doi.org/10.1016/j.applthermaleng.2026.132211
  12. Garud, K. S., Hwang, S. G., Han, J. W., & Lee, M. Y. (2022). Performance characteristics of the direct spray oil cooling system for a driving motor of an electric vehicle. International Journal of Heat and Mass Transfer, 196, 123228. https://doi.org/10.1016/j.ijheatmasstransfer.2022.123228
  13. Garud, K. S., & Lee, M. Y. (2024). Thermal management characteristics of electric vehicle driving motor with oil spray cooling based on spray locations and oil types. Applied Thermal Engineering, 248, 123234. https://doi.org/10.1016/j.applthermaleng.2024.123234
  14. Gronwald, P. O., & Kern, T. A. (2021). Traction motor cooling systems: A literature review and comparative study. IEEE transactions on transportation electrification, 7(4), 2892-2913. https://doi.org/10.1109/TTE.2021.3075844
  15. Huh, K. Y., Lee, E., & Koo, J. (1998). Diesel spray atomization model considering nozzle exit turbulence conditions. Atomization and Sprays, 8(4). https://doi.org/10.1615/AtomizSpr.v8.i4.60
  16. Jafari, M., Jowkar, S., & Morad, M. R. (2021). Low flow rate spray cooling by a flow blurring injector. International Communications in Heat and Mass Transfer, 122, 105168. https://doi.org/10.1016/j.icheatmasstransfer.2021.105168
  17. Kabakuş, A., Sönmez, F., & Öztürk, A. (2024). Thermal analysis of photovoltaic panel cooled by electrospray using different fluids. Duzce University Journal of Science and Technology, 12(4), 2271-2282. https://doi.org/10.29130/dubited.1492678
  18. Kabakuş, A., & Yakut, K. (2024). Optimization of finned heat sinks with electrospray cooling: Full factorial method. Heat Transfer Research, 55(6). https://doi.org/10.1615/HeatTransRes.2023049860
  19. Karabey, A. (2017, January). Determination of Heat and Flow Characteristics in Spray Cooling with Rectangular Finned Heat Sink. In Proceedings ILASS–Europe 2017. 28th Conference on Liquid Atomization and SpraySystems. https://doi.org/10.4995/ILASS2017.2017.4596
  20. Karabey, A., & Tanış, M. (2024). Optimization of spray characteristics of full cone nozzles used in pesticide application using the taguchi method. Karadeniz Fen Bilimleri Dergisi, 14(2), 605-618. https://doi.org/10.31466/kfbd.1400316
  21. Karabey, A., & Yakut, K. (2024). Analyzing the heat and flow characteristics in spray cooling by using an optimized rectangular finned heat sink. Heat Transfer Research, 55(11). https://doi.org/10.1615/HeatTransRes.2024051370
  22. Ning, J., Ren, Z., Sun, L., Song, Z., Zhu, S., & Gao, X. (2024). Study on spray cooling characteristics of dry ice particles for IGBT in high-speed trains {fr} Etude des caractéristiques de refroidissement par pulvérisation des particules de glace sèche pour l'igbt dans le train à grande vitesse. International Journal of Refrigeration, 157, 150-158. https://doi.org/10.1016/j.ijrefrig.2023.11.001
  23. Osta, M. H., Yakut, K., Özakın, A. N., & Yeşildal, F. (2026). Experimental investigation of spray cooling in PV panel using air-assisted nozzle. Journal of Enhanced Heat Transfer, 33(1). https://doi.org/10.1615/JEnhHeatTransf.2025059896
  24. Park, J., An, J., Han, K., Choi, H. S., & Park, I. S. (2022). Enhancement of cooling performance in traction motor of electric vehicle using direct slot cooling method. Applied Thermal Engineering, 217, 119082. https://doi.org/10.1016/j.applthermaleng.2022.119082
  25. Sarmadian, A., Dunne, J. F., Long, C. A., Jose, J. T., Pirault, J. P., & Rouaud, C. (2020). Heat flux correlation models for spray evaporative cooling of vibrating surfaces in the nucleate boiling region. International Journal of Heat and Mass Transfer, 160, 120159. https://doi.org/10.1016/j.ijheatmasstransfer.2020.120159
  26. Sönmez, F., Kabakuş, A., & Öztürk, A. (2026). Determination of optimum parameters in photovoltaic panel with electrospray cooling. Ain Shams Engineering Journal, 17(5), 104106. https://doi.org/10.1016/j.asej.2026.104106
  27. Tao, Y., Huai, X., Wang, L., & Guo, Z. (2011). Experimental characterization of heat transfer in non-boiling spray cooling with two nozzles. Applied Thermal Engineering, 31(10), 1790-1797. https://doi.org/10.1016/j.applthermaleng.2011.02.025
  28. Vladyko, I., Miskiv, N., Serdyukov, V., Nazarov, A., & Surtaev, A. (2023). Influence of the nozzle-to-surface distance on spray cooling efficiency. Fluids, 8(7), 191. https://doi.org/10.3390/fluids8070191
  29. Wang, Y., Liu, M., Liu, D., Xu, K., & Chen, Y. (2010). Experimental study on the effects of spray inclination on water spray cooling performance in non-boiling regime. Experimental Thermal and Fluid Science, 34(7), 933-942. https://doi.org/10.1016/j.expthermflusci.2010.02.010
  30. Wu, Y., Wang, Q., Liu, Q., Guo, K., & Hao, Z. (2024). Comparison of air-cooled and spray-cooled heat transfer performance with phase change material coupled with microgroove flat plate heat pipe. Journal of Enhanced Heat Transfer, 31(7). 2024;31(7). https://doi.org/10.1615/JEnhHeatTransf.2024052239
  31. Xie, J., Wong, T. N., & Duan, F. (2016). Modelling on the dynamics of droplet impingement and bubble boiling in spray cooling. International Journal of Thermal Sciences, 104, 469-479. https://doi.org/10.1016/j.ijthermalsci.2016.02.016
  32. Yesildal, F., Ozakin, A. N., & Yakut, K. (2022). Optimization of operational parameters for a photovoltaic panel cooled by spray cooling. Engineering Science and Technology, an International Journal, 25, 100983. https://doi.org/10.1016/j.jestch.2021.04.002
  33. Yesildal, F., & Yakut, K. (2017). Optimization of the spray cooling parameters for a heat sink by the Taguchi method. Atomization and Sprays, 27(12). https://doi.org/10.1615/AtomizSpr.2018019951
  34. Zhang, M., Chen, X., Liang, K., Li, Z., Wang, X., Huang, J.,. & Zhou, H. (2025). Heat transfer mechanism of spray cooling under vibrational conditions: effects of spray volume flow rate and nozzle inclination angle. International Communications in Heat and Mass Transfer, 164,108820. https://doi.org/10.1016/j.icheatmasstransfer.2025.108820
  35. Zhao, X., Zhang, B., Yang, Z., & Zhao, Y. (2020). Surface orientation effects on heat transfer performance of spray cooling. International Journal of Heat and Mass Transfer, 147,118960. https://doi.org/10.1016/j.ijheatmasstransfer.2019.118960