Hidrolik türbin-jeneratör ünitesinde denge etkisinin teorik ve deneysel analizi

Amaç & Hipotez:Denge durumu, yüksek dönüş hızlarında ve büyük mekanik yükler altında çalışan hidrolik türbin-jeneratör ünitelerinin kararlılığı, dinamik davranışı ve titreşim özellikleri üzerinde önemli bir etkiye sahiptir.

📊

Temel Bulgular & Veri:Bu çalışma, 150 MW'lık bir Francis türbininin operasyonel kararlılığı üzerindeki denge etkilerinin etkisini araştırmaktadır.

💡

Sonuç & Katkı:Sonuçlar, denge durumunun güvenli titreşim seviyelerinin ve kararlı çalışmanın korunmasında kritik bir rol oynadığını göstermektedir.

🔬Tür:Modelleme & Sayısal Simülasyon

📍Kapsam:Genişletilmiş Akademik Örneklem

⚙️Değişkenler:Hidrolik türbin · denge · dengesizlik

Özet

Denge durumu, yüksek dönüş hızlarında ve büyük mekanik yükler altında çalışan hidrolik türbin-jeneratör ünitelerinin kararlılığı, dinamik davranışı ve titreşim özellikleri üzerinde önemli bir etkiye sahiptir. Bu çalışma, 150 MW'lık bir Francis türbininin operasyonel kararlılığı üzerindeki denge etkilerinin etkisini araştırmaktadır. İlk olarak, denge etkilerini içeren yeni bir doğrusal olmayan çok serbestlik dereceli matematiksel model geliştirilmiştir. Model için gerekli olan sertlik ve sönümleme katsayıları, türbin-jeneratör ünitesine monte edilen sensörler kullanılarak hem mutlak hem de göreceli titreşimler ölçülerek çeşitli çalışma koşulları altında belirlenmiştir. Daha sonra, türbinden elde edilen titreşim verileri, denge arızasından önce, sırasında ve sonra model tahminleriyle karşılaştırılmıştır. Sonuçlar, denge durumunun güvenli titreşim seviyelerinin ve kararlı çalışmanın korunmasında kritik bir rol oynadığını göstermektedir. Ayrıca, önerilen matematiksel model, farklı çalışma senaryoları altında türbinin dinamik davranışını başarıyla yakalamaktadır. Bu çalışma, hidrolik türbinler için geliştirilmiş tasarım, kurulum ve işletme stratejilerini destekleyebilecek hem teorik hem de pratik bilgiler sağlamaktadır.

Abstract

The balance condition has a significant influence on the stability, dynamic behavior, and vibration characteristics of hydraulic turbine-generator units operating at high rotational speeds and under large mechanical loads. This study investigates the impact of balance effects on the operational stability of a 150 MW Francis turbine. First, a new nonlinear multi-degree-of-freedom mathematical model incorporating balance effects is developed. The stiffness and damping coefficients required for the model were identified under various operating conditions by measuring both absolute and relative vibrations using sensors installed on the turbine-generator unit. Subsequently, vibration data obtained from the turbine were compared with model predictions before, during, and after balance failure. The results demonstrate that the balance condition plays a critical role in maintaining safe vibration levels and stable operation. Furthermore, the proposed mathematical model successfully captures the dynamic behavior of the turbine under different operating scenarios. This study provides both theoretical and practical insights that can support improved design, installation, and operational strategies for hydraulic turbines.

Anahtar kelimeler

Hidrolik türbin denge dengesizlik arıza analizi matematiksel model Hydraulic turbine balance unbalance failure analysis mathematical model

🔖

Bu Makaleye Atıf Yap

Özdemir, O., Yücel, H., Kahraman, G. (2026). Hidrolik türbin-jeneratör ünitesinde denge etkisinin teorik ve deneysel analizi. Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi, Cilt: 17 Sayı: 3. https://doi.org/10.24012/dumf.1990483

📄 Tam Metin PDF Okuyucu

Yeni Sekmede Aç ↗

↗Yeni Sekme

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (44)

A. Rahman, O. Farrok, and M. M. Haque, “Environmental impact of renewable energy source based electrical power plants: Solar, wind, hydroelectric, biomass, geothermal, tidal, ocean, and osmotic,” Renew. Sustain. Energy Rev., vol. 161, Art. no. 112279, Jun. 2022.
A. Betti, E. Crisostomi, G. Paolinelli, F. Ruffini, and M. Tucci, “Condition monitoring and predictive maintenance methodologies for hydropower plants equipment,” Renew. Energy, vol. 171, pp. 246-258, Jun. 2021.
G. Kahraman, “Investigation of the effect of operating conditions change on water hammer in hydroelectric power plants,” J. Fail. Anal. Prev., vol. 20, pp. 1987-1991, 2020.
Trivedi C, “Study of pressure pulsations in a Francis turbine designed for frequent start‑stop. ASME J Energy Resour Technol 143:081302, 2021.
A. Zabihi, “Assessment of faults in the performance of hydropower plants within power systems,” Energy Syst. Res., vol. 7, Art. no. 5, 2024.
Singh P, Singh S, Soltanali H, Vardhan S, “A reliability, availability and maintainability (RAM) model for electromechanical components in hydropower plants”, Int J Syst Assur Eng Manag., 2025.
F. Dao, Y. Zeng, Y. Zou, X. Li, and J. Qian, “Acoustic vibration approach for detecting faults in hydroelectric units: A review,” Energies, vol. 14, Art. no. 7840, 2021.
A. T. Lemeski, D. Tekgün, O. Keysan, K. Leblebicioğlu, and M. Göl, “Noninvasive condition monitoring for eccentricity fault detection in large hydro generators,” Turk. J. Electr. Eng. Comput. Sci., vol. 34, pp. 67-79, 2026.
K. Kumar and R. P. Saini, “A review on operation and maintenance of hydropower plants,” Sustain. Energy Technol. Assess., vol. 49, Art. no. 101704, 2022.
H. Zhang, W. Che, Y. Cao, Z. Guan, and C. Zhu, “Condition monitoring and fault diagnosis of rotating machinery towards intelligent manufacturing: Review and prospect,” Iran. J. Sci. Technol. Trans. Mech. Eng., vol. 49, pp. 1-18, 2025.
L. Selak, P. Butala, and A. Sluga, “Condition monitoring and fault diagnostics for hydropower plants,” Comput. Ind., vol. 65, pp. 924-936, 2014.
C. Trivedi, “A review on fluid-structure interaction in hydraulic turbines: A focus on hydrodynamic damping,” Eng. Fail. Anal., vol. 77, pp. 1-22, 2017.
J. Zhang, Z. Ma, X. Wang, Q. Wu, and L. Zhang, “Transient vibration of shafting in coupled hydraulic-mechanical-electrical-structural systems during start-up,” Appl. Math. Model., vol. 124, pp. 860-875, 2023.
L. Nie, X. Wang, J. Zhang, Z. Ma, L. Zhang, and W. Guo, “Dynamic characteristics analysis and vibration control of coupled bending-torsional systems for axial-flow hydraulic generating sets,” Chaos Solitons Fractals, vol. 187, Art. no. 115401, 2024.
B. A. Adaramola, “Vibration monitoring experiment for annual rotor balance and shaft alignment of turbo generators,” J. Adv. Eng. Technol., vol. 7, pp. 2348-2355, 2018.
G. Song, X. Huang, H. Li, Z. Wang, and D. Wang, “Impact of installation deviations on the dynamic characteristics of the shaft system for a 1 GW hydro-generator unit,” Machines, vol. 12, Art. no. 473, 2024.
M. R. Elhami, M. R. Nejafi, and M. T. Bafghi, “Vibration analysis and numerical simulation of fluid-structure interaction on a turbine blade,” J. Braz. Soc. Mech. Sci. Eng., vol. 43, Art. no. 1, 2021.
W. K. M. Ridha, K. R. Kashyzadeh, and S. Ghorbani, “Common failures in hydraulic Kaplan turbine blades and practical solutions,” Materials, vol. 16, Art. no. 3303, 2023.
M. Nässelqvist, R. Gustavsson, and J. O. Aidanpää, “A methodology for protective vibration monitoring of hydropower units,” ASME J. Dyn. Syst. Meas. Control, vol. 135, Art. no. 041007, 2013.
J. Unterluggauer, E. Doujak, and C. Bauer, “Fatigue analysis of a prototype Francis turbine based on strain-gauge measurements,” WasserWirtschaft, vol. 109, pp. 66-71, 2019.
L. Niu, Q. Sun, C. Ma, J. Liao, and J. Pu, “Research on modal analysis of rotor shaft systems of hydro-generators,” J. Phys. Conf. Ser., vol. 1549, Art. no. 042084, 2020.
Y. Ri, S. Ryang, and G. Ryong, “Influence of sliding bearing stiffness on dynamic response of hydro-generator shafts,” Int. J. Appl. Mech. Eng., vol. 30, Art. no. 3, 2025.
W. Wang, Y. Shang, and Z. Yao, “Predictive analysis of shafting vibration for hydraulic turbine-generator units,” Water, vol. 14, Art. no. 2714, 2022.
G. L. Rodal, “Online condition monitoring of synchronous generators using vibration signals,” M.S. thesis, Norwegian Univ. Sci. Technol., Trondheim, Norway, 2020.
J. Zhang, J. Zhang, X. Huang, G. Chen, Z. Wang, and C. You, “Effect of generator rotor radial deviation on unbalanced magnetic pull of a 1000 MW hydro-generator unit,” Processes, vol. 11, Art. no. 899, 2023.
P. Manikandan and F. A. Khan, “Dampers to suppress vibrations in hydro turbine-generator shafts due to subsynchronous resonance,” in Adv. Fluid Dyn., Proc. ICAFD 2018, 2020.
Y. Shi, J. Zhou, J. Huang, Y. Xu, and B. Liu, “Vibration fault identification framework for shafting systems of hydropower units,” Sensors, vol. 22, Art. no. 4266, 2022.
P. Lizunov and V. O. Nedin, “Gyroscopic forces influence on oscillations of rotating shafts,” Strength Mater. Theory Struct., vol. 105, pp. 223-234, 2020.
M. N. Sahinkaya, A. H. G. Abulrub, and C. R. Burrows, “An adaptive multi-objective controller for flexible rotor and magnetic bearing systems,” ASME J. Dyn. Syst. Meas. Control, vol. 133, Art. no. 031003, 2011.
B. Xu, D. Chen, H. Zhang, and R. Zhou, “Dynamic analysis and modeling of a novel fractional-order hydro-turbine generator,” Nonlinear Dyn., vol. 81, pp. 1263-1275, 2015.
B. Guo, B. Xu, D. Chen, W. Ye, and H. Li, “Vibration characteristics of a hydroelectric generating system during load rejection,” J. Comput. Nonlinear Dyn., vol. 14, Art. no. 071006, 2019.
M. K. Al-Solihat, M. Nahon, and K. Behdinan, “Dynamic modeling and simulation of a spar floating offshore wind turbine considering rotor speed variations,” ASME J. Dyn. Syst. Meas. Control, vol. 141, Art. no. 081014, 2019.
J. Li, D. Chen, G. Liu, X. Gao, K. Miao, Y. Li, and B. Xu, “Analysis of gyroscopic effects on hydro-turbine generator units,” Mech. Syst. Signal Process., vol. 132, pp. 138-150, 2019.
D. Rondon, G. B. Benti, J. O. Aidanpää, and R. Gustavsson, “Rotordynamic characterization of eight-pad tilting-pad bearings in vertical rotors,” ASME J. Energy Resour. Technol., vol. 144, Art. no. 012111, 2022.
J. Cao, P. E. Allaire, and T. Dimond, “Coupled lateral and torsional nonlinear transient rotor-bearing system analysis,” ASME J. Dyn. Syst. Meas. Control, vol. 137, Art. no. 091011, 2015.
P. Paturu, I. Vinoth Kanna, and G. Mallela, “Free vibration analysis of a 70 MW hydropower turbine rotor,” Int. J. Ambient Energy, vol. 42, pp. 880-888, 2021.
A. Chaubey, H. Chelladurai, and S. S. Lamba, “Condition monitoring of rotating shafts using virtual instrumentation,” in Proc. 5th Int. 26th AIMTDR Conf., Guwahati, India, pp. 1-6, 2014.
G. Stachowiak and A. W. Batchelor, Engineering Tribology, 4th ed. Oxford, U.K.: Butterworth-Heinemann, 2013.
L. Sun, J. Shi, T. Jiang, Z. Li, Q. Xie, Z. Liu, and W. Xu, “Stability analysis of the rotor-journal bearing system considering shear and gaseous cavitation,” Lubricants, vol. 12, no. 2, 48, 2024.
L. R. Moorthi, J. I. Inayat-Hussain, and A. A. Zakaria, “Effect of wear on the dynamic characteristics of a rigid rotor supported by journal bearings,” Scientific Reports, vol. 14, Article 9918, 2024.
Y. Chen, Z. Zhao, H. Zhang, X. Li, and Z. Shi, “Analytical and experimental investigation of nonlinear dynamic characteristics of hydrodynamic bearings for oil film instability detection,” Machines, vol. 13, no. 6, 444, 2025.
D. Rondon, G. B. Benti, J. O. Aidanpää, and R. Gustavsson, "Rotordynamic characterization of eight-pad tilting-pad bearings in vertical rotors," ASME J. Energy Resour. Technol., vol. 144, no. 1, Art. no. 012111, 2022.
D. Bojic, O. Husnjak, O. Oreskovic, and J. Letal, "High vibration caused by hydraulic unbalance on a 144 MW Francis turbine unit," presented at HydroVision Int., 2017.
P. Sapkota, S. Paudel, R. Poudel, S. Chitrakar, H. P. Neopane, and B. Thapa, "Experimental investigation of vibrational signal in a fault induced Francis runner," Front. Mech. Eng., vol. 11, Art. no. 1536603, 2025.