Dergiler / Politeknik Dergisi / 2026 / Cilt: 29 Sayı: 3

Ti-6Al-4V Alaşımının Mikro Cep Frezeleme İşleminde Isıl İşlem, Soğutma Koşulları ve Takım Giriş Stratejilerinin Çapak Genişliği, Takım Aşınması ve Yüzey Kalitesi Üzerine Etkileri

Effects of Heat Treatment, Cooling Conditions and Tool Entry Strategies on Burr Width, Tool Wear and Surface Quality in Micro-Pocket Milling of Ti-6Al-4V Alloy

Elif Malyer(MANİSA CELÂL BAYAR ÜNİVERSİTESİ)0000-0001-9041-3842
Sayfa
1–10
Yayın Tarihi
2026-03-29
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Bulgular, MQL koşullarında en düşük takım aşınması ve en yüksek yüzey kalitesi elde edildiğini göstermiştir.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu araştırma, Ti-6Al-4V alaşımının mikro cep frezeleme işlemlerinde mikroyapı, takım giriş stratejisi ve soğutma/yağlama koşullarının işleme performansına etkilerini incelemektedir.
📊
Temel Bulgular & Veri:Farklı mikroyapılar oluşturmak için tavlama ve yaşlandırma ısıl işlemleri uygulanmıştır.
💡
Sonuç & Katkı:Bulgular, MQL koşullarında en düşük takım aşınması ve en yüksek yüzey kalitesi elde edildiğini göstermiştir.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Mikro frezeleme · Ti-6Al-4V · ısıl işlem

Özet

Bu araştırma, Ti-6Al-4V alaşımının mikro cep frezeleme işlemlerinde mikroyapı, takım giriş stratejisi ve soğutma/yağlama koşullarının işleme performansına etkilerini incelemektedir. Farklı mikroyapılar oluşturmak için tavlama ve yaşlandırma ısıl işlemleri uygulanmıştır. Helisel, dalma ve rampalama olmak üzere üç farklı giriş stratejisi tercih edilmiştir. Deneysel süreç, farklı yağlama stratejilerinin işleme performansı üzerindeki etkilerini karşılaştırmalı olarak ortaya koyabilmek amacıyla; kuru kesme, minimum miktarda yağlama (MQL) ve bor–su esaslı özel bir çalışma akışkanı (WBF) kullanılan üç ayrı koşul altında yürütülmüştür. İşleme performansı yüzey pürüzlülüğü ve çapak genişliği ölçümleriyle değerlendirilmiştir. Çalışmalarda 0,6 mm çapında AlTiCrN kaplamalı mikro freze kullanılmıştır. Bulgular, MQL koşullarında en düşük takım aşınması ve en yüksek yüzey kalitesi elde edildiğini göstermiştir. Yaşlandırılmış numunelerde α-faz oranındaki artış sertliği yükseltmiş, buna karşılık çapak oluşumu belirgin biçimde artmıştır. WBF koşulları, düşük talaş yapışması sağlasa da sınırlı yağlama etkisi nedeniyle takım aşınmasını artırmıştır. Bu çalışmada deneysel süreç, farklı yağlama stratejilerinin işleme performansı üzerindeki etkilerini karşılaştırmalı olarak ortaya koyabilmek amacıyla; kuru kesme, minimum miktarda yağlama (MQL) ve bor–su esaslı özel bir çalışma akışkanı (WBF) kullanılan üç ayrı koşul altında yürütülmüştür.

Abstract

The study focuses on evaluating how variations in microstructure, tool entry strategy, and cooling/lubrication environment affect the micro-pocket milling performance of Ti-6Al-4V alloy. Distinct microstructures were achieved through annealing and aging heat treatments. Three tool entry strategies—helical, plunge, and ramp—were utilized, while cutting was carried out under dry, minimum quantity lubrication (MQL), and a boron–water-based experimental medium (WBF). Surface roughness, burr size, and tool condition were measured to assess process performance. All trials employed a 0.6 mm AlTiCrN-coated micro end mill. Experimental observations demonstrated that MQL provided the most favorable surface finish with minimal tool degradation. In aged specimens, a higher α-phase content increased hardness but also led to greater burr formation. Although the WBF medium decreased chip adhesion, its limited lubrication capacity contributed to accelerated tool wear.

🔖

Bu Makaleye Atıf Yap

Malyer, E. (2026). Ti-6Al-4V Alaşımının Mikro Cep Frezeleme İşleminde Isıl İşlem, Soğutma Koşulları ve Takım Giriş Stratejilerinin Çapak Genişliği, Takım Aşınması ve Yüzey Kalitesi Üzerine Etkileri. Politeknik Dergisi, Cilt: 29 Sayı: 3, 1–10. https://doi.org/10.2339/politeknik.1816826

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (54)

  1. Bajpai V., Kushwaha A. K. and Singh R. K.,“Burr formation and surface quality in high speed micromilling of titanium alloy (Ti-6Al-4V)”, International Manufacturing Science and Engineering Conference Proceedings, V002T03A017, (2013).
  2. Kumar P., Bajpai V. and Singh R., “Burr height prediction of Ti-6Al-4V in high speed micro-milling by mathematical modeling”, Manufacturing Letters, 11: 12-16, (2017).
  3. Cheng J., Jin Y., Wu J., Wen X., Gong Y., Shi J. and Cai G., “Experimental study on a novel minimization method of top burr formation in micro-end milling of Ti-6Al-4V”, International Journal of Advanced Manufacturing Technology, 86: 2197-2217, (2016).
  4. Yadav A. K., Bajpai V., Singh N. K. and Singh R. K., “FE modeling of burr size in high-speed micro-milling of Ti-6Al-4V”, Precision Engineering, 49: 287-292, (2017).
  5. Özel T., Olleak A. and Thepsonthi T., “Micro milling of titanium alloy Ti-6Al-4V: 3-D finite element modeling for prediction of chip flow and burr formation”, Production Engineering, 11: 435-444, (2017).
  6. Gilbert R., “Heat treating of titanium and titanium alloys”, ASM Handbook, (1991).
  7. Ezugwu E. O. and Wang Z. M., “Titanium alloys and their machinability—a review”, Journal of Materials Processing Technology, 68 (3): 262-274, (1997).
  8. Ensarioğlu C. and Çakır M. C., “Titanyum ve alaşımlarının işlenebilirlik etüdü – Bölüm I”, Mühendis ve Makina, 46 (546): 36-46, (2005).
  9. Kumar M. and Bajpai V., “Experimental investigation of top burr formation in high-speed micro-milling of Ti-6Al-4V alloy”, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 234 (4): 730-738, (2020).
  10. Niu Z., Jiao F. and Cheng K., “An innovative investigation on chip formation mechanisms in micro-milling using natural diamond and tungsten carbide tools”, Journal of Manufacturing Processes, 31: 382-394, (2018).
  11. Yi J., Wang X., Jiao L., Li M., Xiang J., Yan P. and Chen S., “Micro-flank milling forces considering stiffness of thin-walled parts”, International Journal of Advanced Manufacturing Technology, 95: 2767-2782, (2018).
  12. Sun Q., Cheng X., Liu Y., Yang X. and Li Y., “Modeling and simulation for micromilling mechanisms”, Procedia Engineering, 174: 760-766, (2017).
  13. Kuram E. and Özçelik B., “Multi-objective optimization using Taguchi-based grey relational analysis for micro-milling of Al 7075 material with ball nose end mill”, Measurement, 46 (6): 1849-1864, (2013).
  14. Afazov S. M., Zdebski D., Ratchev S. M., Segal J. and Liu S., “Effects of micro-milling conditions on the cutting forces and process stability”, Journal of Materials Processing Technology, 213 (5): 671-684, (2013).
  15. Dib M. H. M., Duduch J. G. and Jasinevicius R. G., “Minimum chip thickness determination by means of cutting force signal in micro end-milling”, Precision Engineering, 51: 244-262, (2018).
  16. Rezaei H., Sadeghi M. H. and Budak E., “Determination of minimum uncut chip thickness under various machining conditions during micro-milling of Ti-6Al-4V”, International Journal of Advanced Manufacturing Technology, 95: 1617-1634, (2018).
  17. Miranda M., Serje D., Pacheco J. and Bris J., “Tool edge radius wear and material removal rate performance charts for titanium micro-milling”, International Journal of Precision Engineering and Manufacturing, 19: 79-84, (2018).
  18. Bayraktar Ş. and Turgut Y., “Al-5083 alaşımının frezelenmesinde kesme kuvveti, yüzey pürüzlülüğü ve çapak yüksekliğinin optimizasyonu”, 7th International Symposium on Machining, 3-5, (2016).
  19. Niknam S. A. and Songmene V., “Analysis of friction and burr formation in slot milling”, Procedia CIRP, 17: 755-759, (2014).
  20. Niknam S. A. and Songmene V., “Milling burr formation, modeling and control: a review”, Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 229 (6): 893-909, (2015).
  21. Kumar P., Kumar M., Bajpai V. and Singh N. K., “Recent advances in characterization, modeling and control of burr formation in micro-milling”, Manufacturing Letters, 13: 1-5, (2017).
  22. Oliaei S. N. B. and Karpat Y., “Built-up edge effects on process outputs of titanium alloy micro-milling”, Precision Engineering, 49: 305-315, (2017).
  23. Jackson M. J., Robinson G. M., Whitfield M. D. and Ahmed W., “Burr formation and elimination in micromilling processes”, International Journal of Nanomanufacturing, 1 (4): 458-467, (2007).
  24. Rehman G. U., Jaffery S. H. I., Khan M., Ali L., Khan A. and Ikramullah Butt S., “Analysis of burr formation in low-speed micro-milling of titanium alloy (Ti-6Al-4V)”, Mechanical Sciences, 9 (2): 231-243, (2018).
  25. Bandapalli C., Singh K. K., Sutaria B. M. and Bhatt D. V., “Experimental investigation of top burr formation in high-speed micro-end milling of titanium alloy”, Machining Science and Technology, 22 (6): 989-1011, (2018).
  26. Attanasio A., Gelfi M., Pola A., Ceretti E. and Giardini C., “Influence of material microstructures in micromilling of Ti-6Al-4V alloy”, Materials, 6 (9): 4268-4283, (2013).
  27. Vipindas K., Kuriachen B. and Mathew J., “Investigations into the effect of process parameters on surface roughness and burr formation during micro end milling of Ti-6Al-4V”, International Journal of Advanced Manufacturing Technology, 100: 1207-1222, (2019).
  28. Thepsonthi T. and Özel T., “Multi-objective process optimization for micro-end milling of titanium alloy (Ti-6Al-4V): an application of Taguchi-based grey relational analysis”, International Journal of Advanced Manufacturing Technology, 63: 903–912, (2012).
  29. Bajpai V., Kushwaha A. K. and Singh R. K., “Characterization of burr formation during high-speed micromilling of Ti-6Al-4V alloy”, ASME 2013 International Manufacturing Science and Engineering Conference, V002T03A017, (2013).
  30. Balázs B., Karoliny T., Radványi L. and Karpuschewski B., “Recent advances in micro milling: tool wear, minimum chip thickness and process stability”, International Journal of Advanced Manufacturing Technology, 114: 2743–2765, (2021).
  31. Wang Y., Liu Y., Zhao W., Sun H. and Zhang Y., “Dynamic response and vibration characteristics in micro-milling of titanium alloy Ti-6Al-4V”, Mechanical Systems and Signal Processing, 187: 109953, (2023).
  32. Pratap T., Sahoo P. and Mishra D., “Influence of tool geometry and cutting parameters on burr formation in micro-milling of titanium alloy”, Precision Engineering, 78: 261–273, (2022).
  33. Aramcharoen A. and Mativenga P. T., “Size effect and tool geometry in micro milling of titanium alloy Ti-6Al-4V”, International Journal of Advanced Manufacturing Technology, 41: 884–893, (2009).
  34. Kim W. Y., Senguttuvan S., Kim S. H., Lee S. W. and Kim S. M., “Numerical study of flow and thermal characteristics in titanium alloy milling with hybrid nanofluid MQL and cryogenic nitrogen cooling”, International Journal of Heat and Mass Transfer, 170: 121005, (2021).
  35. Khosravi J., Azarhoushang B., Barmouz M., Bösinger R. and Zahedi A., “High-speed milling of Ti-6Al-4V under a supercritical CO₂ + MQL hybrid cooling system”, Journal of Manufacturing Processes, 82: 1–14, (2022).
  36. Ahmed Y. S. and Ryon A., “Tribological performance of a hybrid CryoMQL system on Ti-6Al-4V milling”, International Journal of Advanced Manufacturing Technology, 120: 8185–8199, (2022).
  37. Wang F., Pang Q. and Yang Q., “Effect of cryogenic cooling on micro-milling properties of titanium alloy”, Journal of Materials Engineering and Performance, 34: 6472–6483, (2025).
  38. Akyol S., “Ti-6Al-4V titanyum alaşımının işlenebilirliğinin ısıl işlem yardımıyla arttırılması”, Doktora Tezi, Fen Bilimleri Enstitüsü, (2007).
  39. Vazquez E., Gomar J., Ciurana J. and Rodríguez C. A., “Analyzing effects of cooling and lubrication conditions in micromilling of Ti-6Al-4V”, Journal of Cleaner Production, 87: 906–913, (2015).
  40. Noghani, M. T., Bayat, O., Moghadam, O., & Mehrizi, V. A., “Effect of various microstructures obtained from heat treatment on machinability behavior of Ti-6Al-4V alloy”, International Journal of Engineering, Transactions A: Basics, 35, 184–190, (2022).
  41. Ahmadi, M., Karpat, Y., Acar, O., & Kalay, Y. E., “Microstructure effects on process outputs in micro-scale milling of heat-treated Ti-6Al-4V titanium alloys”, Journal of Materials Processing Technology, 252, 333–347, (2018).
  42. Akkus H. and Yaka H., “Optimization of cutting parameters in turning of titanium alloy (grade 5) by analysing surface roughness, tool wear and energy consumption”, Experimental Techniques, 46 (2): 945–956, (2021).
  43. Gökçe H. and Çiftçi İ., “Molibden ve alaşımlarının frezelenmesinde takım aşınmasının incelenmesi”, Politeknik Dergisi, 27(3): 839–847, (2024).
  44. Chaabani S., Arrazola P. J., Ayed Y., Madariaga A., Tidu A. and Germain G., “Comparison between cryogenic coolants effect on tool wear and surface integrity in finishing turning of Inconel 718”, Journal of Materials Processing Technology, 285: 116780, (2020).
  45. Ramli A. S., Sharif S., Said A. Y. M., Yusop M. S. M., Karim Z. and Mohruni A. S., “Investigation of tool entry strategy when pocket milling titanium alloy Ti-6Al-4V under wet condition”, AIP Conference Proceedings, 2129(1): 070004, (2019).
  46. Akagündüz E., “Investigation of microstructures and surface scratch strength of heat treated Ti6Al4V alloys”, M.S. thesis, Department of Materials Science and Engineering, Gebze Technical University, Kocaeli, (2008).
  47. Akkus H. and Yaka H., “Experimental and statistical investigation of the effect of cutting parameters on surface roughness, vibration and energy consumption in machining of titanium 6Al-4V ELI (grade 5) alloy”, Measurement, 167: 108465, (2021)
  48. Ankem S., Margolin H., Greene C. A., Neuberger B. W. and Oberson G., “Mechanical properties of alloys consisting of two ductile phases”, Progress in Materials Science, 51(5): 632–709, (2006).
  49. Patil R., Shinde S., Marla D., Joshi S., “Experimental analysis of burr formation in drilling of Ti-6Al-4V alloy”, International Journal of Mechatronics and Manufacturing Systems, 9(3): 237–245, (2016).
  50. Pimenov D. Yu., Mia M., Gupta M. K., Machado A. R., Tomaz I. V., Sarikaya M., Wojciechowski S., Mikolajczyk T. and Kapłonek W., “Improvement of machinability of Ti and its alloys using cooling-lubrication techniques: a review and future prospect”, Journal of Materials Research and Technology, 11: 719–753, (2021).
  51. Aslantas K., Ekici E. and Cicek A., “Optimization of process parameters for micro milling of Ti-6Al-4V alloy using Taguchi-based grey relational analysis”, Measurement, 128: 419–427, (2018).
  52. Yaman K. and Tekiner Z.,“Investigation of the Effect of Built-Up Edge on Chip Morphology at the Cutting Edge During Turning Operation”, Politeknik Dergisi, 27(6): 2325–2333, (2024).
  53. Demirel T., Yağmur S., Kayır Y. and Kurt A., “Investigation of thrust force, torque and chip formation in tapping threading by finite element method”, Politeknik Dergisi, 27(4): 1633–1641, (2024).
  54. Karan J., Hiren S. and Satish D., “Burr formation mechanism in machining – a review”, Proceedings of the National Conference on Progress, Research and Innovation in Mechanical Engineering (PRIME), 167, (2017).