Dergiler / Ordu Üniversitesi Bilim ve Teknoloji Dergisi / 2017 / Cilt: 7 Sayı: 2

Kalça Protezinin Aşınma Özellikleri Üzerinde Çoklu Tabakalı Kaplanmasının Etkilerinin Sonlu Elemanlar Metoduyla Nümerik Analizi

Numerical Analysis of Effect of Multilayer Coating on the Wear Properties of Hip Prosthesis by Finite Element Method

Sayfa
201–214
Yayın Tarihi
2017-12-15
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Elde edilen sonuçlar, metal femur başının çoklu tabakalı kaplanmasının polietilen bileşeninin aşınma dayanımını artıracağı görülmüştür.  

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Total kalça protezi uygulamalarında kullanılan metal alaşımlarının kullanım sürelerinin artırılmasına yönelik çalışmalar gelişen tıp ve malzeme teknolojileriyle beraber devam etmektedir.
📊
Temel Bulgular & Veri:Metal alaşımları vücut sıvısı içerisinde bulunan çeşitli iyonlar, mineraller ve proteinlerle etkileşime girerek korozyon ve metal iyonizasyonuna uğramaktadır.
💡
Sonuç & Katkı:Elde edilen sonuçlar, metal femur başının çoklu tabakalı kaplanmasının polietilen bileşeninin aşınma dayanımını artıracağı görülmüştür.  
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Kalça Protezi · Bio malzeme · Ti6Al4V

Özet

Total kalça protezi uygulamalarında kullanılan metal alaşımlarının kullanım sürelerinin artırılmasına yönelik çalışmalar gelişen tıp ve malzeme teknolojileriyle beraber devam etmektedir. Metal alaşımları vücut sıvısı içerisinde bulunan çeşitli iyonlar, mineraller ve proteinlerle etkileşime girerek korozyon ve metal iyonizasyonuna uğramaktadır. Bunun sonucunda ise polietilen bileşen kullanım ömründen erken aşınmaya maruz kalmaktadır. Kalça protezlerinde kullanılan metal bileşenlerin korozyon dayanımının artırılması ve iyonizasyonun önlenmesi için seramik bileşenlerle kaplanmaktadır. Bu çalışmada kalça protezlerinde yaygın olarak kullanılan metal-polietilen çifti Ti6Al4V-ultra yüksek moleküler ağırlıklı polietilen bileşenlerinin aşınma özellikleri incelenmiştir. Metal femur başının çoklu tabakalı kaplanmasının ve tabaka sayısının polietilen asetabular linerin aşınması üzerindeki etkileri nümerik olarak ANSYS programı yardımıyla incelenmiştir. Elde edilen sonuçlar, metal femur başının çoklu tabakalı kaplanmasının polietilen bileşeninin aşınma dayanımını artıracağı görülmüştür.  

Abstract

Researches on increasing the lifetime of metal alloys used in total hip replacement applications, continue in parallel with developing medicine and material engineering. Metal alloys expose to the corrosion and ionization by interacting with the ions, proteins, and minerals in the body fluid. As a result of this, polyethylene component of the hip prosthesis exposes to early wear. Metal components of the hip prosthesis are coated with ceramic materials in order to avoid metal ionization and enhance the corrosion resistance. In this study, the wear properties of widely used Ti6Al4V-UHMWPE metal-polyethylene couple in the hip prosthesis is investigated. The effect of the coating of metal femoral head and the effect of layer number on the wear of polyethylene acetabular liner is numerically studied by ANSYS software. Results showed that the multilayer coating of metal femoral head will increase the wear resistance of the polyethylene component.

🔖

Bu Makaleye Atıf Yap

Bahçe, E., Aslan, A. K., Güler, M. S., Çakır, N., Emir, E. (2017). Kalça Protezinin Aşınma Özellikleri Üzerinde Çoklu Tabakalı Kaplanmasının Etkilerinin Sonlu Elemanlar Metoduyla Nümerik Analizi. Ordu Üniversitesi Bilim ve Teknoloji Dergisi, Cilt: 7 Sayı: 2, 201–214. https://ajindex.com/articles/1279458

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (35)

  1. Aihua L, Jianxin D, Haibing C, Yangyang C & Jun Z (2012). Friction and wear properties of TiN, TiAlN, AlTiN and CrAlN PVD nitride coatings. International Journal of Refractory Metals and Hard Materials 31: 82–88
  2. Bal B S, Khandkar A, Lakshminarayanan R, Clarke I, Hoffman A A & Rahaman M N (2008). Testing of silicon nitride ceramic bearings for total hip arthroplasty. Journal of Biomedical Materials Research Part B: Applied Biomaterials 87(2): 447-454
  3. Cui W, Qin G, Duan J & Wang H (2017). A graded nano-TiN coating on biomedical Ti alloy: Low friction coefficient, good bonding and biocompatibility. Materials Science and Engineering: C 71: 520-528
  4. Davim J P (2013). Biomaterials and Medical Tribology. Woodhead Publishing, UK
  5. Fahrenholtz W G, Wuchina E J, Lee W E & Zhaou Y (2014). Ultra-High Temperature Ceramics Materials for Extreme Environment Applications. John Wiley & Sons, New Jersey
  6. Gallegos-Cantú S, Hernandez-Rodriguez M A L, Garcia-Sanchez E, JuarezHernandez A, Hernandez-Sandoval J & Cue-Sampedro R (2015). Tribological study of TiN monolayer and TiN/CrN (multilayer and superlattice) onCo–Cr alloy. Wear 330-331: 439–447
  7. Gilewicz A, Chmielewska P, Murzynski D, Dobruchowska E & Warcholinski B (2016). Corrosion resistance of CrN and CrCN/CrN coatings deposited using cathodic arc evaporation in Ringer's and Hank's solutions. Surface and Coatings Technology 299: 7-14
  8. Good V, Widding K, Hunter G & Heuer D (2005). Oxidized zirconium: a potentially longer lasting hip implant. Materials & Design 26 (7): 618-622
  9. Hesketh J, Meng Q, Dowson D & Neville A (2013). Biotribocorrosion of metalon-metal hip replacements: How surface degradation can influence metal ion formation. Tribology International 65: 128-137
  10. Holleck H, Schier V (1995). Multilayer PVD coatings for wear protection. Surface and Coatings Technology 76-77: 328-336
  11. Holzwarth U & Cotogno G (2012). Total hip arthroplasty- State of the Art, Challenges and Prospects, Publications Office of the European Union
  12. Huang M D, Liu Y, Meng F Y, Tong L N & Li P (2013). Thick CrN/TiN multilayers deposited by arc ion plating. Vacuum 89: 101-104
  13. H¨ubler R, Cozza A, Marcondes T L, Souza R B & Fiori F F (2001). Wear and corrosion protection of 316-L femoral implants by deposition of thin films. Surface and Coatings Technology 142-144: 1078-1083
  14. Khanna R, Kokubo T, Matsushita T, Nomura Y, Nose N, Oomori Y & Takadama H (2015). Novel artificial hip joint: A layer of alumina on Ti–6Al–4V alloy formed by micro-arc oxidation. Materials Science and Engineering: C, 55: 393- 400 15. Khanna R, Kokubo T, Matsushita T & Takadama H (2016). Fabrication of dense α-alumina layer on Ti-6Al-4V alloy hybrid for bearing surfaces of artificial hip joint. Materials Science and Engineering: C 69: 1229-1239
  15. Li D.J., Liu F, Wang M X, Zhang J J & Liu Q X (2006). Structural and mechanical properties of multilayered gradient CrN/ZrN coatings. Thin Solid Films 506– 507: 202 – 206
  16. Lin Y T, Wu J S S & Chen J H (2016). The study of wear behaviours on abducted hip joint prostheses by an alternate finite element approach. Computer methods and programs in biomedicine 131: 143-155
  17. Long M & Rack, H J (1998). Titanium alloys in total joint replacement—a materials science perspective. Biomaterials 19 (18): 1621-1639
  18. McEntire B J, Bal B S, Rahaman M N, Chevalier J & Pezzotti G (2015). Ceramics and ceramic coatings in orthopaedics. Journal of the European Ceramic Society 35 (16): 4327-4369
  19. Mckee GK & Ferrar J. W J (1996). Bone Jt. Surg, 48: 245
  20. Mendizabal L., Lopez A., Bayón R., Herrero-Fernandez P., Javier Barriga J., Javier J. Gonzalez J.J. (2016). Tribocorrosion response in biological environments of multilayer TaN films deposited by HPPMS. Surface and Coatings Technology 295: 60-69.
  21. Ortega-Saenz J A, Alvarez-Vera M & Hernandez-Rodriguez M A L (2013). Biotribological study of multilayer coated metal-on-metal hip prostheses in a hip joint simulator. Wear 301(1): 234-242
  22. Okumiya M & Griepentrog M (1999). Mechanical properties and tribological behavior of TiN–CrAlN and CrN–CrAlN multilayer coatings. Surface and Coatings Technology 112: 123–128
  23. Ou Y X, Lin J, Che H L, Moore J J, Sproul W D & Lei M K (2015). Mechanical and tribological properties of CrN/TiN superlattice coatings deposited by a combination of arc-free deep oscillation magnetron sputtering with pulsed dc magnetron sputtering. Thin Solid Films 594:147–155
  24. Ou Y X, Lin J, Tonga S, Sproul W D & Lei M K (2016). Structure, adhesion and corrosion behavior of CrN/TiN superlattice coatings deposited by the combined deep oscillation magnetron sputtering and pulsed dc magnetron sputtering. Surface & Coatings Technology 293: 21–27
  25. Pakhaliuk V, Polyakov A, Kalinin M & Kramar V (2015). Improving the Finite Element Simulation of Wear of Total Hip Prosthesis’ Spherical Joint with the Polymeric Component. Procedia Engineering 100: 539-548
  26. Perumal G, Geetha M, Asokamani R &Alagumurthi N (2014). Wear studies on plasma sprayed Al 2 O 3–40wt% 8YSZ composite ceramic coating on Ti–6Al– 4V alloy used for biomedical applications. Wear 311(1): 101-113
  27. Rahaman M N, Yao A, Bal B S, Garino J P & Ries M D (2007). Ceramics for prosthetic hip and knee joint replacement. Journal of the American Ceramic Society 90(7): 1965-1988
  28. Silva M, Heisel C & Schmalzried T P (2005). Metal-on-metal total hip replacement. Clinical Orthopaedics and Related Research 430: 53-61
  29. Taylor M & Prendergast P J (2015). Four decades of finite element analysis of orthopaedic devices: where are we now and what are the opportunities?. Journal of biomechanics 48(5): 767-778
  30. Zameer S, & Haneef M (2015). Fatigue Life Estimation of Artificial Hip Joint Model Using Finite Element Method. Materials Today: Proceedings 2(4-5): 2137-2145
  31. Zhang J, Chen Z, Wang L, Li D & Jin Z A (2017). Patient-specific wear prediction framework for an artificial knee joint with coupled musculoskeletal multibodydynamics and finite element analysis. Tribology International 109: 382-389
  32. Zhang Z G, Rapaud O, Allain N, Mercs D, Baraket M, Dong C & Coddet C (2009). Microstructures and tribological properties of CrN/ZrN nanoscale multilayer coatings. Applied Surface Science 255: 4020–4026
  33. Good V, Widding K, Hunter G & Heuer D (2005). Oxidized zirconium: a potentially longer lasting hip implant. Materials & Design 26 (7): 618-622
  34. Ortega-Saenz J A, Alvarez-Vera M & Hernandez-Rodriguez M A L (2013). Biotribological study of multilayer coated metal-on-metal hip prostheses in a hip joint simulator. Wear 301(1): 234-242
  35. Ou Y X, Lin J, Che H L, Moore J J, Sproul W D & Lei M K (2015). Mechanical and tribological properties of CrN/TiN superlattice coatings deposited by a combination of arc-free deep oscillation magnetron sputtering with pulsed dc magnetron sputtering. Thin Solid Films 594:147–155