Dergiler / European Mechanical Science / 2023 / Cilt: 7 Sayı: 4

Single-pulse MIG welded Perform 700 steel joints with various welding parameters

Sayfa
246–252
Yayın Tarihi
2023-12-20
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The boundary of soft fusion zone and hard heat affected zone formed the weakest point through the joint.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this work, Perform 700 steel sheets with 5-mm thickness were welded with single pulse MIG welding method with different welding currents and welding speeds.
📊
Temel Bulgular & Veri:The maximum tensile strength was obtained as 594.75 MPa at 140A welding current and 450 mm/min welding speed.
💡
Sonuç & Katkı:The boundary of soft fusion zone and hard heat affected zone formed the weakest point through the joint.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Welding · Joining · Mechanical Properties

Abstract

In this work, Perform 700 steel sheets with 5-mm thickness were welded with single pulse MIG welding method with different welding currents and welding speeds. The welded specimens were subjected to tensile tests, hardness measurements and microstructural observations. According to the results, the heat input has an important role in tensile strength of the joint. The maximum tensile strength was obtained as 594.75 MPa at 140A welding current and 450 mm/min welding speed. The tensile specimens were always separated between fusion zone and heat affected zone. The heat affected zones have exhibited tempered martensitic structure. The tempering effect have increased the sizes of the martensitic structure; therefore, the hardness was considerably increased. However, the fusion zone, which was consisted of bainitic structure inside the ferrite matrix, was exhibited soft and ductile behavior. The boundary of soft fusion zone and hard heat affected zone formed the weakest point through the joint.

🔖

Bu Makaleye Atıf Yap

ÖZEN, F. (2023). Single-pulse MIG welded Perform 700 steel joints with various welding parameters. European Mechanical Science, Cilt: 7 Sayı: 4, 246–252. https://ajindex.com/articles/1022517

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

  1. Park, G.W., Park, M., Kim, B.J., Shin, S., Kim, H.C., Park, I.W., et al., (2022). Microstructure and mechanical properties of a gas-tungsten-arc-welded Fe-24Mn-3.5Cr-0.4C high manganese steel pipe using a Fe-22Mn-2.34Ni-0.38C welding wire. Materials Characterization. 194(11): 1–12. doi: 10.1016/j.matchar.2022.112469
  2. Onar, V., (2022). Mechanical and Microstructural Characterizations of Resistance Spot Welded Dissimilar TWIP/304L Stainless Steel. Transactions of the Indian Institute of Metals. 75: 1731–1739. doi: 10.1007/s12666-021-02446-9
  3. Kekik, M., Özen, F., Onar, V., Aslanlar, S., (2022). Investigation effect of resistance spot welding parameters on dissimilar DP1000HF/CP800 steel joints. Sadhana - Academy Proceedings in Engineering Sciences. 47(4): 1–17. doi: 10.1007/s12046-022-01977-1
  4. Bjorhovde, R., (2004). Development and use of high-performance steel. Journal of Constructional Steel Research. 60(3–5): 393–400. doi: 10.1016/S0143-974X(03)00118-4
  5. Özsaraç, U., Onar, V., Özen, F., Aslanlar, Y.S., Akkaş, N., (2019). Effect of current and welding time on tensile-peel strength of resistance spot welded TWIP 1000 and martensitic steels. Indian Journal of Chemical Technology. 26(4): 248–51
  6. Özsaraç, U., Onar, V., Özen, F., Aslanlar, Y.S., Akkaş, N., (2019). Effect of welding time on tensile-shear load in resistance spot welded TRIP 800 and microalloyed steels. Indian Journal of Chemical Technology. 26(4): 355–7
  7. Lun, N., Saha, D.C., Macwan, A., Pan, H., Wang, L., Goodwin, F., et al., (2017). Microstructure and mechanical properties of fiber laser welded medium manganese TRIP steel. Materials and Design. 131: 450–9. doi: 10.1016/j.matdes.2017.06.037
  8. Hong, S.-H., Eo, D.-R., Lee, S., Cho, J.-W., Kim, S.-J., (2023). Strong resistance to Zn-assisted liquid metal embrittlement of austenitic-TWIP/martensitic-HSLA multi-layered steel sheets additively manufactured by laser cladding. Acta Materialia. 258(March): 119224. doi: 10.1016/j.actamat.2023.119224
  9. Shreyas, P., Panda, B., Vishwanatha, A.D., (2021). Embrittlement of hot-dip galvanized steel: A review. AIP Conference Proceedings, vol. 2317. p. 1–15
  10. Phung, T.A., (2022). Experimental study on mechanical properties and microstructure of PERFORM 700 steel butt-welding joints using in high load-bearing structures. Journal of Science and Technique. 17(1): 53–63. doi: 10.56651/lqdtu.jst.v17.n01.301
  11. Petronis, E., Cerwenka, G., Emmelmann, C., (2017). Hybrid laser-arc wel