Journals / Gazi Mühendislik Bilimleri Dergisi / 2023 / Cilt: 9 Sayı: 2

Effect of Surface Topography on Soil Amplification

Yüzey Topoğrafyasının Zemin Büyütmesine Etkisi

Pages
322–333
Publication Date
2023-08-31
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Dynamic analysis results show that PGA values change significantly when surface topography is used.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Soil amplification is known as the increase in amplitudes of seismic waves as they pass through the soil layers.
📊
Key Findings & Data:A software called SiteEffect3D has been developed to examine soil behavior with the three-dimensional (3-D) finite element method.
💡
Conclusion & Impact:Dynamic analysis results show that PGA values change significantly when surface topography is used.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Zemin büyütmesi · Yüzey topoğrafyası · Deprem

Abstract

Soil amplification is known as the increase in amplitudes of seismic waves as they pass through the soil layers. It depends on many factors such as seismic bedrock depth and slope, the thickness of its layers, physical and lithological properties, discontinuities, and topography. This study, the effect of surface topography on local soil amplification was investigated. A software called SiteEffect3D has been developed to examine soil behavior with the three-dimensional (3-D) finite element method. With this software, the effect of surface topography on local soil amplification was investigated using various 3D models. These models were exposed to the 17 August 1999 earthquake acceleration record and synthetic acceleration records, and the peak ground acceleration (PGA) graphs were obtained as a result of the dynamic analysis. Dynamic analysis results show that PGA values change significantly when surface topography is used. PGA values are high on hills with few flat areas, and the slope of the hill also affects the result. There are also remarkable changes in the PGA results on the hills located in the regions where the flat areas are wider. However, the effect of the slope is relatively less on the hills in the wide plains.

Özet

Zemin büyütmesi, sismik dalgaların zemin tabakalarından geçerken genliklerindeki artış olarak bilinmektedir. Zemin büyütmesi, sismik ana kaya derinliği ve eğimi, fiziksel ve litolojik özellikleri, yanal ve düşey süreksizlikler, tabakalarının kalınlığı ve topoğrafya gibi bir çok etkene bağlıdır. Bu çalışmada yüzey topoğrafyasının yerel zemin büyütmesine etkisi araştırılmıştır. Zemin tepkisinin üç boyutlu (3-B) sonlu eleman yöntemiyle inceleyebilmek için SiteEffect3D isminde bir yazılım geliştirilmiştir. Bu yazılım ile yüzey topoğrafyasının yerel zemin büyütmesine etkisi çeşitli 3-B modeller kullanılarak incelenmiştir. Bu modeller 17 Ağustos 1999 depremi ivme kaydı ve sentetik ivme kayıtlarına maruz bırakılmış, dinamik analiz sonucunda en yüksek yer ivmesi (PGA) sonuçlarından grafikler elde edilmiştir. Dinamik analiz sonuçları, yüzey topoğrafyası kullanıldığında PGA değerlerinin önemli ölçüde değiştiğini göstermektedir. Düz alanların az olduğu tepeliklerde PGA değerleri yüksek çıkmakta, tepenin eğimi de sonucu etkilemektedir. Düz alanların daha geniş olduğu bölgelerde bulunan tepeliklerde de PGA sonuçlarında dikkate değer değişiklikler olmaktadır. Ancak geniş düzlükler içerisinde bulunan tepelerde eğim değişiminin etkisi görece daha azdır.

🔖

Cite This Article

DOĞAN, A., DİKMEN, Ü. (2023). Effect of Surface Topography on Soil Amplification. Gazi Mühendislik Bilimleri Dergisi, Cilt: 9 Sayı: 2, 322–333. https://ajindex.com/articles/960508

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (1)

  1. G. Kumar, G. Pavan and S.P. Regalla, ‘‘Optimization of support material and build time in fused deposition modeling (FDM)’’ Trans Tech Publications- In Applied Mechanics and Materials, vol 110, pp. 2245-2251, 2012. doi:10.4028/www.scientific.net/AMM.110-116.2245 [2] B. Ergene, İ. Şekeroğlu, Ç. Bolat and B. Yalçın, “An experimental investigation on mechanical performances of 3D printed lightweight ABS pipes with different cellular wall thickness” Journal of Mechanical Engineering and Sciences, vol. 15, no. 8, pp. 8169-8177, 2021. doi:10.46519/ij3dptdi.1069544 [3] W.C. Smith and R. W. Dean, ‘‘Structural characteristics of fused deposition modeling polycarbonate material’’ Polymer Testing, vol. 32, no. 8, Pages 1306–1312, 2013. doi:10.1016/j.polymertesting.2013.07.014 [4] C. Weller, R. Kleer and F. T. Piller, ‘‘Economic implications of 3D printing: Market structure models in light of additive manufacturing revisited’’, Int. J. Production Economics, vol. 164, pp. 43–56, 2015. doi:10.1016/j.ijpe.2015.02.020 [5] N. Ercan ve D. E. Yunus, “Eriyik yığma modelleme ile üretilen hücresel sandviç panellerin basma özelliklerinin incelenmesi” presented at the 4 th Internatıonal Congress on 3d Prıntıng (Additive Manufacturing) Technologıes and Dıgıtal Industry (3D-PTC2019), Antalya, 2019. [6] S. H. Yazdani, A. H. Akbarzadeh, H. Niknam and K. Hermenean, ‘‘3D printed architected polymeric sandwich panels: Energy absorption and structural performance’’,Composite Structures, vol. 200, pp. 886–909, 2018. doi:10.1016/j.compstruct.2018.04.002 [7] B. Ergene and Ç. Bolat, “An experimental study on the role of manufacturing parameters on the dry sliding wear performance of additively manufactured PETG” International Polymer Processing, vol. 37, no. 3, pp. 255-270, 2022. doi:10.1515/ipp-2022-0015 [8] B. Ergene and B. Yalçın, “Eriyik yığma modelleme (EYM) ile üretilen çeşitli hücresel yapıların mekanik performanslarının incelenmesi” Gazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi, cilt 38, sayı 1, ss. 201-218, 2023. doi:10.17341/gazimmfd.945650 [9] D. Chaidas, K. Kitsakis and S. Maropoulos, “The impact of temperature changing on surface roughness of FFF process”. 20th Innovative Manufacturing Engineering and Energy Conference, Kallithea Chalkidiki, 2016. [10] M. Günay, R. Kaçar, H. Yılmaz, H. Demir ve S. Gündüz, “3D Baskı ile Üretilen PLA Esaslı Numunelerde Doluluk Oranı ve Tarama Açısının Mekanik Özelliklere Etkisi”, 3rd International Congress on 3D Printing (Additiv