Journals / Textile and Apparel / 2015 / Cilt: 25 Sayı: 2

PARAMETERS OPTIMIZATION FOR DEGUMMING OF COTTON-STRAW BAST FIBER

PAMUK BİTKİSİNDEN ELDE EDİLEN SAK LİFLERİNİN TERBİYESİNİN OPTİMİZASYONU

Pages
135–139
Publication Date
2015-12-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Experimental results showed that the optimum combination of parameters for first boiling was 8g/L NaOH, 9g/L H2O2, 1:100 bath ratio and 30min treatment time by using mathematical statistic analysis.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Abstract: As a bast fiber, cotton-straw bast fiber consists of cellulosic and non-cellulosic substances, such as hemicellulose, pectin, lignin, and wax, and these noncellulosic substances affect the application of cotton-straw base fiber.
📊
Key Findings & Data:Alkali-H2O2 treatment does not only remove hemicellulose, lignin and pectin effectively, but bleach fiber as well.
💡
Conclusion & Impact:Experimental results showed that the optimum combination of parameters for first boiling was 8g/L NaOH, 9g/L H2O2, 1:100 bath ratio and 30min treatment time by using mathematical statistic analysis.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Cotton-straw bast fiber · degumming · orthogonal experimental

Abstract

Abstract: As a bast fiber, cotton-straw bast fiber consists of cellulosic and non-cellulosic substances, such as hemicellulose, pectin, lignin, and wax, and these noncellulosic substances affect the application of cotton-straw base fiber. Alkali-H2O2 treatment does not only remove hemicellulose, lignin and pectin effectively, but bleach fiber as well. Through orthogonal experimental, the degumming for first boiling and second boiling of alkali-H2O2 was investigated. Experimental results showed that the optimum combination of parameters for first boiling was 8g/L NaOH, 9g/L H2O2, 1:100 bath ratio and 30min treatment time by using mathematical statistic analysis. Optimum technological parameters of second boiling for degumming of cotton-straw base fiber were alkaline content 12g/L, hydrogen peroxide content 17g/L, temperature 80 , and time 60min by using the fuzzy comprehensive evaluation

🔖

Cite This Article

LI, L., SHENG, G., WANG, Q. (2015). PARAMETERS OPTIMIZATION FOR DEGUMMING OF COTTON-STRAW BAST FIBER. Textile and Apparel, Cilt: 25 Sayı: 2, 135–139. https://ajindex.com/articles/943718

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (11)

  1. Gassan J., Bledzki A.K., 1997, “The Influence of Fiber Surface Treatment on the Mechanical Properties of Jute Polypropylene Composites”, Composites: Part A, Vol. 28A(12), pp. 1001-1005
  2. Bledzki A.K., Gassan J., 1999, “Composites Reinforced with Cellulose Based Fiber”, Progress in Polymer Science, Vol. 24(2), pp.221-274
  3. Gautam S, Arup C., 2008, “Dynamic Mechanical and Thermal Properties of PE-EPDM Based Jute Fiber Composites”, Journal of Applied Polymer Science, Vol. 108(6), pp.3442-3453
  4. Li L., Sheng G.Z., Wu L., 2008, “Development and Utilization of Cotton Bast Fibers resource”, Plant Fiber Science in China, Vol.30(4), pp.204-206
  5. Liu L. 2010, “Investigation on the Spinning Technology and Yarn Property of treated cotton-straw bast fibers/cotton”, Thesis of Xi’an Polytechnic University, China, pp.27-42 6. Jinhua W., Ramaswamy G. N., 2003, “One-Step Processing and Bleaching of Mechanically Separated Kenaf Fibers: Effects on Physical and Chemical Properties”, Textile Research Journal, Vol. 73(4), pp. 339-344
  6. Akin D.E., Dodd R.B., Perkins W., Henriksson G., 2000, “Spray Enzymatic Retting: A New Method for Processing Flax Fibers”, Textile Research Journal, Vol.70(6), pp.486-494
  7. Henriksson G., Akin D.E., Rigsby L.L., Patel N., 1997, “Influence of Chelating Agents and Mechanical Pretreatment on Enzymatic Retting of Flax”, Textile Research Journal, Vol. 67(11), pp.829-836
  8. Wang H.M., Postle R., Kessler R.W., 2003, “Removing Pectin and Lignin During Chemical Processing of Hemp for Textile Applications”, Textile Research Journal, Vol. 73(8),pp.664-669
  9. Henriksson G., Eriksson K.E.L., Akin D.E., 1998, “Chemical/Physical Retting of Flax Using Detergent and Oxalic Acid at High pH”, Textile Research Journal, Vol.68(12), pp.942-947
  10. Romanoschi O., Romanoschi S., Collier J.R., and Collier B.J., 1997, “Kenaf Alkali Processing”, Cellulose Chemistry and Technology, Vol.31(5-6), pp.347-359 12. Hyung-Min C., 2002, “One-Bath Dyeing and Nonformaldehyde Durable Press Finishing of Cotton Using Dialdehyde and a Monochlorotriazinyl Reactive Dye”, Textile Research Journal, Vol. 72(6), pp. 469-473
  11. Yang S.H., 2001, “Plant Fiber Chemical”, China Light Industry Press, Beijing, China, 55 14. Jiang F.C., Shao K., Jiang Y., 1989, “Ramie Spinning”, Textile Industry Press, Beijing, China, 53 15. Qu L.J., Zhu S.F., Liu M. J., and Wang S.Y., 2005, “The Mechanism and Technology Parameters Optimization of Alkali-H2O2 One–Bath Cooking and Bleaching of Hemp