Journals / Konya Journal of Engineering Sciences / 2021 / Cilt: 9 Sayı: 2

The Effect of Various Interpolation Methods Applied at Aerial Lidar Data on DTM Accuracy

HAVA LİDARI VERİLERİNE UYGULANAN FARKLI ENTERPOLASYON YÖNTEMLERİNİN SAM DOĞRULUĞUNA ETKİSİ

Pages
377–394
Publication Date
2021-06-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

As a result of the researches, it is discovered that the weighted-average method gives better results than others.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Many application areas have approved Digital Terrain Models (DTM) as a subject.
📊
Key Findings & Data:Then, two different areas were determined, with a total of 1250 points in a fixed area on the investigated area.
💡
Conclusion & Impact:As a result of the researches, it is discovered that the weighted-average method gives better results than others.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Ağırlıklı Ortalama Enterpolasyonu · En Küçük Eğrilikli Yüzey · En Yakın Komşu Enterpolasyonu

Abstract

Many application areas have approved Digital Terrain Models (DTM) as a subject. It is primarily used in many sectors, such as civil engineering studies, geographical information systems. When producing DTMs, they should be fast-produced, as they should always be up-to-date, sufficient accuracy for users and economical to manufacture. One of the essential factors affecting the accuracy of DTM is the selected interpolation method. In this study, weighted average interpolation, polynomial interpolation, multi quadratic interpolation, linear interpolation in the network of triangles, small curvature surface interpolation, and the nearest neighbor interpolation methods were explained theoretically and then the points of the area were tested in the model with the Surfer program. The comparison of standard deviation results of these six different interpolation methods, which are frequently used in DTM studies in the literature, is the most crucial purpose of the study. A sigma test was used to eliminate unsuitable measurements on the results. Then, two different areas were determined, with a total of 1250 points in a fixed area on the investigated area. The number of bases and samples for these areas are arranged differently. Then, using each interpolation method, the land model was reexamined, and the result between them was evaluated. As a result of the researches, it is discovered that the weighted-average method gives better results than others.

Özet

Sayısal Arazi Modelleri (SAM), konu olarak birçok uygulama alanı tarafından benimsenmiştir. Özellikle sivil amaçlı mühendislik çalışmaları, coğrafi bilgi sistemleri gibi çeşitli sektörlerde kullanılmaktadır. SAM’ların üretimi yapılırken, daima güncel olması gerektiği için hızlı üretilebilir olmalı, kullanıcılar için yeterli doğrulukta olmalı ve üretimi ekonomik olmalıdır. SAM'ın doğruluğunu etkileyen önemli faktörlerden birisi, tercih edilen enterpolasyon yöntemidir. Bu çalışmada ağırlıklı ortalama ile enterpolasyon, polinom enterpolasyon, multikuadrik enterpolasyon, üçgenler ağında lineer enterpolasyonu, küçük eğrilikli yüzey enterpolasyonu ve en yakın komşu enterpolasyon yöntemleri öncelikle teorik olarak açıklanmıştır ardından endüstriyel yazılımla araziye ait noktalar modelde test edilmiştir. Literatürde SAM çalışmalarında sık kullanılan bu altı farklı enterpolasyon yöntemlerine ait standart sapma sonuçlarının karşılaştırılması yapılan çalışmada en önemli amaçtır. Sonuçlar üzerinde uyuşumsuz ölçülerin ayıklanması için sigma testi uygulanmıştır. Sonra, çalışılan arazi üzerinde sabit bir alan içerisinde toplamda 1250 nokta olacak şekilde, iki farklı alan belirlenmiştir. Bu alanlar için dayanak ve örneklem sayıları farklı olarak ayarlanmıştır. Daha sonra her bir enterpolasyon yöntemi kullanılarak, arazi modeli tekrar incelenmiş ve aralarındaki sonuç değerlendirilmiştir. Araştırmalar sonucunda ağırlıklı ortalama yöntemin diğerlerine göre daha iyi sonuç verdiği tespit edilmiştir.

🔖

Cite This Article

ARIKAN, D., YILDIZ, F., MAKİNECİ, H. B. (2021). The Effect of Various Interpolation Methods Applied at Aerial Lidar Data on DTM Accuracy. Konya Journal of Engineering Sciences, Cilt: 9 Sayı: 2, 377–394. https://ajindex.com/articles/909081

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. Akçın, H., 1998, GPS ölçülerinden pratik yüksekliklerin elde edilmesi üzerine bir çalışma, Doktora Tezi, Y.T.Ü., Fen Bilimleri Enstitüsü, İstanbul.
  2. Ayhan, M.E., Alp, O., Üstün, M., “1993, Rastgele Dağılmış Verilerden Bilgisayar Desteğinde Yüzey Modelleme”, T.U.J.J.B, Ankara, 103-118, 8-11 Haziran 1993.
  3. Bigdeli, B., Gomroki, M., & Pahlavani, P., 2020, Generation of digital terrain model for forest areas using a new particle swarm optimization on LiDAR data, Survey Review, 52(371), 115-125.
  4. Briggs, I.C., 1974, Machine Contouring Using Minimum Curvature, Geophysics, 39, 1, 39-48.
  5. Chen, C., Li, Y., Zhao, N., Guo, B., & Mou, N., 2018, Least squares compactly supported radial basis function for digital terrain model interpolation from airborne Lidar point clouds. Remote Sensing, 10(4), 587. Erkanlı, Y.,1986, Koordinatlandırılmıs modelde ve alanda enterpolasyon, kollakasyon yöntemlerinin uygulanması ve neticeleri, Harita ve Kadastro Mühendisligi Dergisi, Ankara, 56-57.
  6. Franke, R., Nielson, G.,1980, Smooth Interpolation of Large Sets of Scattered Data, International Journal for Numerical Methods in Engineering, 15, 1691-1704.
  7. Güler, A., 1978, Sayısal Arazi Modellerinde İnterpolasyon Yöntemleri, Harita Dergisi, 85, 53-70,1978.
  8. Güler, A., 1985, Sayısal arazi modellerinde iki enterpolasyon yöntemi ile denemeler, Harita ve Kadastro Mühendisliği Dergisi, 52-53, 98-113.
  9. Hardy, R.L., 1990, Theory and Applications of the Multiquadric-Biharmonic Method: 20 Years of Discovery 1968-1988,
  10. Computers Math. Applic., Vol. 19, No.8/9, pp.163-208.
  11. Hardy, R.L.,1971, Multiquadric Equations of Topography and Other Irregular Surfaces, Journal of Geophysical Research, Vol. 76, No.8, pp.1905-1915.
  12. Hardy, R.L.,1972, Analytical Topographic Surfaces by Spatial Intersection, P.E.R.S., Vol. 38, No.5, pp. 452- 458. Hardy, R.L.,1975, Research Results in The Application of Multiquadric Equations to Surveying and Mapping Problems, Surveying and Mapping, Vol. 35, pp.321-332.
  13. İnal, C. ve Yiğit, C. Ö., 2003, “Jeodezik Uygulamalarda Kriging Enterpolasyon Yönteminin Kullanılabilirliği”, TUJK 2003
  14. Yılı Bilimsel Toplantısı, Coğrafi Bilgi Sistemleri ve Jeodezik Ağlar Çalıştayı, Konya, s.177-185., 24-26 Eylül 2003.
  15. İnal, C., 1996, Yerel Jeoit Geçirilerek GPS Sonuçlarından Yüksekliklerin Belirlenmesi, Selçuk Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi, Konya,11,15-21.
  16. Karaaslan, Ö., Kayıkçı, E. T., Aşık, Y.,2016, Jeoid Yüksekliklerini Belirlemek İçin Kullanılan Enterpolasyon Metotlarının Trabzon