SavedAdd your journal

Journals / Politeknik Dergisi / 2023 / Cilt: 26 - Sayı: 1

A Comparative Study on Wear and Machinability Behaviors of AM20, AJ21 and AS21 Magnesium Alloys

AM20, AJ21 ve AS21 Magnezyum Alaşımlarının Aşınma ve İşlenebilirlik Davranışları Üzerine Karşılaştırmalı Bir Çalışma

Birol AKYÜZ
Pages
243–248
Publication Date
2023-03-27
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The machinability of the alloys were increase with increasing cutting speed.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This paper is a comparative study on mechanical properties, wear resistance and machinability behaviors of AM20, AJ21 and AS21 (Mg-2Al-X) cast magnesium alloys.
📊
Key Findings & Data:The effects of the changing in third alloy component (x:0.5 Mn, 1 Sr and 1 Si, and constant 2 Al, wt.%) in these alloys on microstructure (intermetallic phases), mechanical and wear properties and machinability (cutting force, surface roughness, FBU and also chip formation) were comparatively analyzed.
💡
Conclusion & Impact:The machinability of the alloys were increase with increasing cutting speed.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:İşlenebilirlik · aşınma direnci · AM20- AJ21- AS21 serisi magnezyum alaşımları

Abstract

This paper is a comparative study on mechanical properties, wear resistance and machinability behaviors of AM20, AJ21 and AS21 (Mg-2Al-X) cast magnesium alloys. The effects of the changing in third alloy component (x:0.5 Mn, 1 Sr and 1 Si, and constant 2 Al, wt.%) in these alloys on microstructure (intermetallic phases), mechanical and wear properties and machinability (cutting force, surface roughness, FBU and also chip formation) were comparatively analyzed. The highest mechanical properties and wear resistance were in AS21 (i.e. 49.2 hardness and 181.5 MPa UTS) alloy and the highest machinability were in AM20 (cutting force 35.6N) alloy. The machinability of the alloys were increase with increasing cutting speed.

Özet

Bu makale, AM20, AJ21 ve AS21 (Mg-2Al-X) döküm magnezyum alaşımlarının mekanik özellikleri, aşınma direnci ve işlenebilirlik davranışları üzerine karşılaştırmalı bir çalışmadır. Bu alaşımlardaki üçüncü alaşım bileşenindeki (x; 0,5 Mn, 1 Sr ve 1 Si ve sabit 2 Al, ağırlıkça %) değişimin mikroyapı (intermetalik fazlar), mekanik ve aşınma özellikleri ve işlenebilirlik üzerindeki etkileri karşılaştırmalı olarak analiz edilmiştir. Bu alaşımların mikroyapısında bulunan intermetalik fazların sertlik, mukavemet, aşınma direnci ve işlenebilirlik özellikleri (kesme kuvveti, yüzey pürüzlülüğü, talaş yığılması-FBU ve ayrıca talaş oluşumu) üzerinde etkisi olduğu görülmüştür. En yüksek mekanik özellikler ve aşınma direnci AS21 (49.2 sertlik ve 181.5 MPa UTS) alaşımındaydı ve en yüksek işlenebilirlik AM20 (kesme kuvveti 35.6N) alaşımındaydı. Alaşımların işlenebilirliği artan kesme hızı ile artmıştır.

🔖

Cite This Article

AKYÜZ, B. (2023). A Comparative Study on Wear and Machinability Behaviors of AM20, AJ21 and AS21 Magnesium Alloys. Politeknik Dergisi, Cilt: 26 - Sayı: 1, 243–248. https://ajindex.com/articles/888291

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. King J. F. “Development of practical high temperature magnesium casting alloys”, Magnesium alloys and their applications, 14-22, (2000)
  2. Schuman S. and Friedrich H.E., “Automotive Applications in Europe”, Magnesium Technology, Metallurgy, Design Data, Applications (Edited by H.E.Friedrich and B.L. Mordike), Springer-Verlag Berlin Heidelberg, Germany, 499-682, (2006)
  3. Zhang P., “Creep behavior of the die-cast Mg–Al alloy AS21”, Scripta Materialia, 52(4), 277-282, (2005)
  4. Kunst M., Fischersworring-Bunk A., L’Esperance G., Plamondon P. and Glatzel U., “Microstructure and dislocation analysis after creep deformation of die-cast Mg–Al–Sr (AJ) alloy”, Materials Science and Engineering: A, 510, 387-392, (2009)
  5. Tönshoff H. K., Denkena B., Winkler R J. and Podolsky C., “Machining, Magnesium Technology, Metallurgy, Design Data, Applications”, (Ed. H. E. Friedrich and B. L.Mordike), Springer-Verlag Berlin Heidelberg, 398, (2006)
  6. Akyüz B., “Influence of aluminum content on the machinability of AS series cast Mg alloys”, Trans. Nonferrous Met. Soc., 24, 3452−3458, (2014)
  7. King J. F., “Technology of Magnesium and Magnesium Alloys, Magnesium Technology (Edited by H.E. Friedrich and B.L.Mordike) Springer-Verlag Berlin Heidelberg, (2006)
  8. Tomac N., Tønnesen K. and Mikac T., “Study of Influence of Aluminum Content on Machinability of Magnesium Alloys”, Strojarstvo: časopis za teoriju i praksu u strojarstvu, 50 (6), 363 – 367, (2008)
  9. Tönshoff H.K., Friemuth T., Winkler J. and Podolsky C., “Improving the Characteristics of Magnesium Workpieces by Burnishing Operations”, Magnesium Alloys and their Applications, (Edited by K. U. Kainer), 406, (2006)
  10. Ünal M., “An Investigation of Casting Properties of Magnesium Alloys”, Gazi University, Institute of Science And Technology, Ph.D. Thesis, (2008)
  11. Evangelista E., Gariboldi E., Lohne O. and Spigarelli S., “High-temperature behaviour of as die-cast and heat treated Mg–Al–Si AS21X magnesium alloy”, Materials Science and Engineering: A, 387, 41-45, (2004)
  12. Ma G.R., Li X.L., Xiao L. and Li Q.F., “Effect of holding temperature on microstructure of an AS91 alloy during semisolid isothermal heat treatment”, Journal of Alloys and Compounds, 496, 577–581, (2010)
  13. Akyüz B., “Comparison of the machinability and wear properties of magnesium alloys”, The International Journal of Advanced Manufacturing Technology, 75(9-12), 1735-1742, (2014)
  14. Gil-Santos A., Moelans N., Hort N. and V