Journals / Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi / 2022 / Cilt: 25 - Sayı: 4

COMPARISON WITH THREE-DIMENSIONAL COORDINATE MEASURING AND LASER SCANNING OF EFFECT OF FORM ERROR OF CUTTING PARAMETERS IN MILLING FREEFORM THIN-WALLED AA 5083-H111 ALLOY

SERBEST FORMLU İNCE CİDARLI AA 5083-H111 ALAŞIMININ FREZELENMESİNDE KESME PARAMETRELERİNİN FORM HATASINA ETKİSİNİ ÜÇ BOYUTLU KOORDİNAT ÖLÇME VE LAZER TARAMA İLE KARŞILAŞTIRILMASI

Pages
633–642
Publication Date
2022-12-03
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In addition, it was observed that the LT measurement results were 63% higher on average than the CMM measurement results.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This article focuses on the comparison of three-dimensional coordinate measuring (CMM) and laser scanning (LS) results of the effect of cutting parameters on form error in the milling of free-form thin-walled AA 5083-H111 alloy.
📊
Key Findings & Data:The experiments were carried out in a CNC vertical machining center under dry machining conditions by using uncoated carbide cutting tool according to the experimental design prepared using the Taguchi L32 orthogonal array.
💡
Conclusion & Impact:In addition, it was observed that the LT measurement results were 63% higher on average than the CMM measurement results.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:AA 5083-H111 · form hatası · koordinat ölçme cihazı

Abstract

This article focuses on the comparison of three-dimensional coordinate measuring (CMM) and laser scanning (LS) results of the effect of cutting parameters on form error in the milling of free-form thin-walled AA 5083-H111 alloy. The experiments were carried out in a CNC vertical machining center under dry machining conditions by using uncoated carbide cutting tool according to the experimental design prepared using the Taguchi L32 orthogonal array. Analysis of variance (ANOVA) was used to determine the most important cutting parameters affecting form errors for CMM and LT. According to the test results, optimum cutting parameters for CMM and LT were determined as 5 mm wall thickness, 0.05 mm/tooth feed rate and 160 m/min cutting speed (A2B1C3). According to the ANOVA results, the most effective cutting parameters on form errors for CMM and LT were 56.18% cutting speed and 68.06% feed rate, respectively. In addition, it was observed that the LT measurement results were 63% higher on average than the CMM measurement results.

Özet

Bu makale, serbest formlu ince cidarlı AA 5083-H111 alaşımının frezelenmesinde kesme parametrelerinin form hatasına etkisi üç boyutlu koordinat ölçme (CMM) ve lazer tarama (LS) sonuçlarının karşılaştırılmasına odaklanılmıştır. Deneyler Taguchi L32 ortogonal dizisi kullanılarak hazırlanan deney tasarımına göre kaplamasız karbür kesici takım kullanılarak kuru işleme şartlarında CNC dik işleme merkezinde yapıldı. CMM ve LT için form hatalarını etkileyen en önemli kesme parametrelerini belirlemek için varyans analizi (ANOVA) kullanıldı. Deney sonuçlarına göre, CMM ve LT için optimum kesme parametrelerinin 5 mm cidar kalınlığı, 0,05 mm/diş ilerleme miktarı ve 160 m/dk kesme hızı (A2B1C3) olarak belirlenmiştir. ANOVA sonuçlarına göre, CMM ve LT için form hataları üzerine en etkin kesme parametresi sırası ile %56,18 kesme hızı ve %68,06 ilerleme miktarı olmuştur. Ayrıca LT ölçüm sonuçları CMM ölçüm sonuçlarına göre ortalama %63 oranında daha yüksek çıktığı görülmüştür.

🔖

Cite This Article

ÇELİK, U., ÖZLÜ, B., DEMİR, H. (2022). COMPARISON WITH THREE-DIMENSIONAL COORDINATE MEASURING AND LASER SCANNING OF EFFECT OF FORM ERROR OF CUTTING PARAMETERS IN MILLING FREEFORM THIN-WALLED AA 5083-H111 ALLOY. Kahramanmaraş Sütçü İmam Üniversitesi Mühendislik Bilimleri Dergisi, Cilt: 25 - Sayı: 4, 633–642. https://ajindex.com/articles/876434

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (11)

  1. Akgün, M., & Demir, H. (2021). Optimization and finite element modelling of tool wear in milling of Inconel 625 superalloy. Journal of Polytechnic, 24(2), 391-400. https://doi.org/10.2339/politeknik.706605
  2. Akgün, M., & Kara, F. (2021). Analysis and optimization of cutting tool coating effects on surface roughness and cutting forces on turning of AA 6061 alloy. Advances in Materials Science and Engineering, 2021, 6498261. https://doi.org/10.1155/2021/6498261
  3. Çırakoğlu, F., Özlü, B., Demir, H. (2021). Hardox 450 çeliğinin lazerle delinmesinde kesme parametrelerinin delik kalitesi üzerine etkisinin incelenmesi ve kesme parametrelerinin optimizasyonu. Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi, 8(2), 913-923. https://doi.org/10.35193/bseufbd.977412
  4. Desai, K.A., & Rao, P.V.M. (2012). On cutter deflection surface errors in peripheral milling. Journal of Materials Processing Technology, 212(11), 2443-2454. https://doi.org/10.1016/j.jmatprotec.2012.07.003
  5. Gök, A., Göloğlu, C., Demirci, H.İ. (2014). Dışbükey ve içbükey yüzeylerin küresel parmak frezelenmesinde takım sehimine bağlı form hatalarının belirlenmesi. Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, 29(2), 365-374.
  6. Harun, Y., Demir, H., Gök A., Akkuş, H. (2018). Determination of optimum cutting parameters on free form surfaces in terms of form errors and machining times. Sigma Journal of Engineering and Natural Sciences, 36(4), 1153-1164.
  7. Harun, Y., Demir, H., GÖK, A. (2017). Optimization of the cutting parameters affecting the surface roughness on free form surfaces. Sigma Journal of Engineering and Natural Sciences, 35(2), 323-331.
  8. Li, Y., & Gu, P. (2004). Free-form surface inspection techniques state of the art review. Computer-Aided Design, 36(13), 1395-1417. https://doi.org/10.1016/j.cad.2004.02.009
  9. Mali, R.A., Gupta, T.V.K., Ramkumar, J. (2021). A comprehensive review of free-form surface milling-Advances over a decade. Journal of Manufacturing Processes, 62, 132-167. https://doi.org/10.1016/j.jmapro.2020.12.014
  10. Nalbant, M., Gökkaya, H., Sur, G. (2007). Application of Taguchi method in the optimization of cutting parameters for surface roughness in turning. Materials & Design, 28(4), 1379-1385. https://doi.org/10.1016/j.matdes.2006.01.008
  11. Oliveira, E.L., Souza, A.F., Diniz, A.E. (2018). Evaluating the influences of the cutting parameters on the surface roughness and form errors in 4-axis milling of thin-walled free-form parts of AISI H13 steel. Journal of the Brazilian Society